The URL can be used to link to this page

20190344 SFP_Lot_2_Gallardo_Homes_3096 A_063019C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND THESE PLANS HAVE BEEN LICENSED TO THE CUSTOMER FOR THE USE IN CONSTRUCTION OF ONE BUILDING ONLY AND ARE SUBJECT TO THE CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/18/19 Job#: JM Lot-2 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/18/19 Job#: JM Lot-2 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/18/19 Job#: JM Lot-2 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/18/19 Job#: JM Lot-2 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/18/19 Job#: JM Lot-2 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/18/19 Job#: JM Lot-2 Window, Skylight and Door Schedule Project Information Contact Information Plan 3096 Rueppell, Inc. (253) 297-8040 Width Height Ref, U-factorQt. Feet Inch Feet Inch Area UA Exempt Swinging Door (24 sq. ft. max.)d E 0.0 0.00 Exempt Glazed Fenestration (15 sq. ft. max.) I I I I I R 1 0.01 0.00 Vertical Fenestration (Windows and doors) Component DescriDtion Ref. U -factor Dining 0.28 Dining 0.28 Entry 0.28 Entry 0.28 Study 0.28 Study 0.28 Family 0.28 Family 0.28 Family 0.28 Kitchen 0.28 Powder 0.28 164.36 Skylights Bonus 0.28 Bonus 0.28 Bonus 0.28 Utility 0.28 Bedroom 2 0.28 Bath 0.28 Bedroom 3 0.28 Stair 0.28 Master Bath 0.28 Master Suite 0.28 Master Suite 0.28 Guest Suite 0.28 MMEME 1.0 Above Grade walls (see Figura 1) U -Factor X Area MMEME Instructions 0,0$6 2,543 142.41 MMEME 0.5 ❑ Floors MMEME UA Instructions w O W:? F MMEME 51.88 0 1.5 MMEME 0-5 Overhead Glazing (Skylights) Component Width Height Ot. Feet Inch Feet Inch MMEME 1 11 11 111 MMEME 1 11 1 f f 11 MMEME 1 11 i 1 1 11 MMEME 1 11 i 1 1 11 MMEME i 11 Wood Frame Wall9rnn 21 int MMEME I 0.280 587 164.36 Skylights MMEME UA s 0.50 0� MMEME Insulation Slab R -Value & Depth 10, 2 ft MMEME Ufactor X Area = UA Instructions MMEME 56.09 0 1.0 MMEME Single Rafter or Joist Vaulted Ceilings U -Factor X Area UA --■-■ No selection -- 61 Select R -Value MMEME 1.0 Above Grade walls (see Figura 1) U -Factor X Area MMEME Instructions 0,0$6 2,543 142.41 MMEME 0.5 ❑ Floors MMEME UA Instructions w O W:? F MMEME 51.88 0 1.5 MMEME 0-5 Below Grade Walls (eee Figure 1) U -Factor X Area MMEME Instructions Select R -value � I No selection -- MMEME F -Factor X Len UA Instructions k0.303 No Slab Below Grade in this project. � MMEME to W O Slab on Grade (See Floure v F -Factor X Lee MMEME Instructions0 Fwa MMEME Location of Ducts MMEME O W W F ~ Instructions Duct Leakage Coefficient --■-I■ I 1.10 H3 go W W> --■-■ 413.74 > a m' Envelope Heat Load --■-■ Figure 1. sum of VAX AT --■-■ Z z_ 0 uwi p w Air Leakage Heat Load --■-■ 0 z¢ 1/nlumo )( QS X dT X .018 --■-■ U W U= Above Grade a W 0U --■-■ 36,991 Btu l Hour w ZON3 N U --■-■ Air teairage +Er ldope ileal Loss W UBe,Z O w O W Z ¢tn --■-■ Building and Duct Heat Load 40,690 Btu I Hour --■-■ z¢ z z 0 Ducts m unconditioned space: Sae= ofBtda3g Heat Loss X 1.fii QQ W� --■-■ I=w 0❑ZZ Maximum Heat Equipment Output Sum of Vertical Fenestration Area and UA Vertical Fenestration Area Weighted U = UA/Area Description Ref. U -factor i i i d Width Height Qt. Feet Inch Feet Inch Sum of Overhead Glazing Area and UA Overhead Glazing Area Weighted U = UA/Area Total Sum of Fenestration Area and UA (for heating system sizing calculations) Area UA f 1 1 11 11 111 1 f 1 11 1 f f 11 1 f 1 11 i 1 1 11 f 1 1 11 i 1 1 11 f Area UA ON 1 11 f 1 f 11 f 1 1 11 11 111 f 1 1 11 f 1 1 11 8.5 26,316 n/a i 1 1 11 UA i 11 Wood Frame Wall9rnn Simple Heating System Size: Washington State This heatincl system sizing calculator is based on the Prescri tive Requirements of the 2015 Washinqton State Energy Code (WSEC) and RCCA Manuals J and S. This calculator will calculate heating loads only. ACCA procedures for sizing cooling systems should be used to determine cooling loads. Please fill out all of the green drop -downs and boxes that are applicable to your project. As you make selections in the drop -downs for each section, some values will be calculated for you. If you do not see the selection you need in the drop-down options, please call the WSU Energy Extension Program at (360) 956-2042 for assistance. Project Information Contact Information Plan 3096 1 JRueppell, Inc. (253)297-8040 Heating System Type: O All other systems O Heat Pomp To see detailed instructions for each section, place your cursor on the word "Insfrtrrtlons" Design Temperature Instructions - Design Temperature Difference (AT) 53 Lacey AT=l=door D 0u0oor � aeries)- ttP•Siv,% TvW Area of Buildina All Climate Zones 2-3 Conditioned Floor Area R-Valuea U-Factora Instructions Conditioned Floor Area (sq ft) 3,096 0.30 Average Ceiling Height Conditioned Volume Instructions Average Ceiling Height (ft) 8.5 26,316 n/a Glazlna and Doors Ufactor X Area = UA Instructions Wood Frame Wall9rnn 21 int l u-o.za � I 0.280 587 164.36 Skylights Ufactor X Area = UA s 0.50 0� -- Insulation Slab R -Value & Depth 10, 2 ft Attic Ufactor X Area = UA Instructions 0.026 2,119 56.09 0 1.0 3b High Efficiency HVAC 3b Single Rafter or Joist Vaulted Ceilings U -Factor X Area UA Instructions � No selection -- 61 Select R -Value 3d High Efficiency HVAC 3d 1.0 Above Grade walls (see Figura 1) U -Factor X Area UA Instructions 0,0$6 2,543 142.41 R-21 Intermediate � 0.5 ❑ Floors U -Factor X Area UA Instructions w O W:? F 0.026 2,075 51.88 0 1.5 5d Efficient Water Heating 5d 0-5 Below Grade Walls (eee Figure 1) U -Factor X Area UA Instructions Select R -value � I No selection -- Slab Below Grade (see Fkauret) F -Factor X Len UA Instructions k0.303 No Slab Below Grade in this project. � *Please refer to Table 8406.2 for complete option descriptions to W O Slab on Grade (See Floure v F -Factor X Lee UA Instructions0 Fwa L No Slab on Grade in this project. � Location of Ducts O W W F ~ Instructions Duct Leakage Coefficient Unconditioned Space I 1.10 H3 go W W> Sum of UA 413.74 > a m' Envelope Heat Load 21,928 BtulHour Figure 1. sum of VAX AT ❑ T Z Z Z z_ 0 uwi p w Air Leakage Heat Load 15,063 Btu l Hour 0 z¢ 1/nlumo )( QS X dT X .018 U W U= Above Grade a W 0U Building Design Heat Load 36,991 Btu l Hour w ZON3 N U a°OZ�Z a Air teairage +Er ldope ileal Loss W UBe,Z O w O W Z ¢tn w U faZ Building and Duct Heat Load 40,690 Btu I Hour a z¢ z z 0 Ducts m unconditioned space: Sae= ofBtda3g Heat Loss X 1.fii QQ W� Duets H condtioned spsce: Sum of 8udrdng Pleat Loss X i I=w 0❑ZZ Maximum Heat Equipment Output 56,967 Btu I Hour �WUWQ� 0 Budding and Duct Heat Loss X 1,40 for forced Ai,Fitrrteee Z� z a z. X UOrn1 Bu &V and Duct Heat ions X 135 for }taw Aa=p Prescriptive Energy Code Compliance for All Climate Zones in Washington Project Information Contact Information Plan 3096 Rueppell, Inc. (253) 297-8040 This project will use the requirements of the Prescriptive Path below and incorporate the the minimum values listed. In addition, based on the size of the structure, the appropriate number of additional credits are checked as chosen by the permit applicant. Authorized Representative *Table R402.1.1 and Table R402.1.3 Footnotes included on Page 2. Date Each dwelling unit in a residential building shall comply with sufficient options from Table R406.2 so as to achieve the following minimum number of credits: 1. Small Dwelling Unit: 1.5 credits ❑ Dwelling units less than 1500 square feet in conditioned floor area with less than 300 square feet of fenestration area. Additions to existing building that are greater than 500 square feet of heated floor area but less than 1500 square feet. 02. Medium Dwelling Unit: 3.5 credits All dwelling units that are not included in #1 or #3. Exception: Dwelling units serving R-2 occupancies shall require 2.5 credits. 03. Large Dwelling Unit: 4.5 credits Dwelling units exceeding 5000 square feet of conditioned floor area. ❑4. Additions less than 500 square feet: .5 credits Table R406.2 Summary All Climate Zones 2-3 Number of Bedrooms 4-5 Airflow in CFM R-Valuea U-Factora Fenestration U-Factorb n/a 0.30 Skylight U -Factor n/a 0.50 Glazed Fenestration SHGCb'e n/a n/a Ceiling" 49' 0.026 Wood Frame Wall9rnn 21 int 0.056 Mass Wall R -Value' 21/21h 0.056 Floor 30, 0.029 Below Grade Wallc m 10/15/21 int + TB 0-042 Slab R -Value & Depth 10, 2 ft n/a *Table R402.1.1 and Table R402.1.3 Footnotes included on Page 2. Date Each dwelling unit in a residential building shall comply with sufficient options from Table R406.2 so as to achieve the following minimum number of credits: 1. Small Dwelling Unit: 1.5 credits ❑ Dwelling units less than 1500 square feet in conditioned floor area with less than 300 square feet of fenestration area. Additions to existing building that are greater than 500 square feet of heated floor area but less than 1500 square feet. 02. Medium Dwelling Unit: 3.5 credits All dwelling units that are not included in #1 or #3. Exception: Dwelling units serving R-2 occupancies shall require 2.5 credits. 03. Large Dwelling Unit: 4.5 credits Dwelling units exceeding 5000 square feet of conditioned floor area. ❑4. Additions less than 500 square feet: .5 credits Table R406.2 Summary 0-1 2-3 Number of Bedrooms 4-5 Airflow in CFM Option Description Credit(s) ,1500 30 la Efficient Building Envelope la 0-5 ❑ 0,5 1b Efficient Building Envelope lb 1.0 ❑ 15 1c Efficient Building Envelope 1c 2-0 ❑ 6ID ld Efficient Building Envelope 1d 0.5 ❑ 120 2a Air Leakage Control and Efficient Ventilation 2a 0.5 ❑ 105 2b Air Leakage Control and Efficient Ventilation 2b 1.0 ❑ eo 2c Air Leakage Control and Efficient Ventilation 2c 1.5 ❑ 150 3a High Efficiency HVAC 3a 1.0 0 1.0 3b High Efficiency HVAC 3b 1.0 ❑ 0=0 F 3c High Efficiency HVAC 3c 1.5 ❑ Oo �o 3d High Efficiency HVAC 3d 1.0 ❑ aWo 4 High Efficiency HVAC Distribution System 1.0 ❑ 5a Efficient Water Heating 5a 0.5 ❑ 0.5 5b Efficient Water Heating 5b 1.0 ❑ w O W:? F 5c Efficient Water Heating 5c 1.5 0 1.5 5d Efficient Water Heating 5d 0-5 ❑ Z 6 Renewable Electric Energy 0.5`1200 kwh 0,0 Total Credits N 3.50 *Please refer to Table 8406.2 for complete option descriptions to W O ~ w (071 lrl13) INTEGRATED 24 ISR WHOLE HOU5E VENTILATION 5Y5TEM. AS AMENDED BY WASHINGTON STATE M1501.1 GENERAL LOCAL EXHAUST OR WHOLE -HOUSE MECHANICAL VENTILATION SYSTEMS AND EQUIPMENT SHALL BE DESIGNED IN ACCORDANCE WITH THIS SECITON. MI5012 RECIRCULATION OF AIR EXHAUST AIR FROM BATHROOMS AND TOILET ROOMS SMALL NOT BE RECIRCULATED WITHIN A RESIDENCE OR TO ANOTHER DWELLING UNIT AND SHALL BE EXHAUSTED DIRECTLY TO THE OUTDOORS. EXHAUST AIR FROM BATHROOMS AND TOILET ROOMS SHALL NOT DISCHARGE INTO AN ATTIC CRAWL SPACE OR OTHER AREAS OF THE BUILDING. M15013 WHOLE -HOUSE MECHANICAL VENTILATION SYSTEM WHOLE -HOUSE MECHANICAL VENTILATION SYSTEMS SHALL BE DESIGNED IN ACCORDANCE WITH SECTIONS M1501.3.1 THROUGH M1501.3.3. MI5013.1 SYSTEM DESIGN EACH DWELLING UNIT OR GUESTROOM SHALL BE EQUIPPED WITH A VENTILATION SYSTEM COMPLYING WITH SECTION M1507.3.4, M1501.3.6 OR M1501.3.7. COMPLIANCE IS ALSO PERMITTED TO BE DEMONSTRATED THROUGH COMPLIANCE WITH THE INTERNATIONAL MECHANICAL CODE OR ASHRAE STANDARD 62.2. M150132 CONTROL AND OPERATION I. LOCATION OF CONTROLS. CONTROLS FOR ALL VENTILATION SYSTEMS SHALL BE READILY ACCESSIBLE BY THE OCCUPANT. 2, INSTRUCTIONS, OPERATING INSTRUCTIONS FOR THE WHOLE -HOUSE VENTILATION SYSTEMS SHALL BE PROVIDED TO THE OCCUPANT BY THE INSTALLER OF THE SYSTEM. 3. LOCAL EXHAUST SYSTEMS. LOCAL EXHAUST SYSTEMS SHALL BE CONTROLLED BY MANUAL SWITCHES, DEHUMIDISTATS, TIMERS, OR OTHER APPROVED MEANS, 4. CONTINUOUS WHOLE -HOUSE VENTILATION SYSTEMS. CONTINUOUS WHOLE -HOUSE VENTILATION SYSTEMS SHALL OPERATE CONTINUOUSLY AND BE EQUIPPED WITH AN OVERRIDE CONTROL. A "FAN ON" SWITCH SHALL BE PERMITTED AS AN OVERIDE CONTROL. CONTROLS SHALL BE CAPABLE OF OPERATING THE VENTILATION SYSTEM WITHOUT ENERGIZING OTHER ENERGY -CONSUMING APPLIANCES. A CLEARLY VISIBLE LABEL SHALL BE AFFIXED TO THE CONTROLS THAT READS "WHOLE HOUSE VENTILATION (SEE OPERATING INSTRUCTIONS)! 5. INTERMITTENT WHOLE -HOUSE VENTILATION SYSTEMS. INTERMITTENT WHOLE -HOUSE VENTILATION SYSTEMS SHALL COMPLY WITH THE FOLLOWING: 5.1 THEY SHALL BE CAPABLE OF OPERATING INTERMITTENTLY AND CONTINUOUSLY. 5.2 THEY SHALL HAVE CONTROLS CAPABLE OF OPERATING THE EXHAUST FANS, FORCED -AIR SYSTEM FANS, OR SUPPLY FANS WITHOUT ENERGIZING OTHER ENERGY -CONSUMING APPLIANCES. 5.3 THE SYSTEM SHALL BE DESIGNED SO THAT IT CAN OPERATE AUTOMATICALLY BASED ON THE TYPE OF CONTROL TIMER INSTALLED. 5.4 THE INTERMITTENT MECHANICAL VENTILATION SYSTEM SHALL OPERATE AT LEAST ONE HOUR OUT OF EVERY FOUR. 5.5 THE SYSTEM SHALL HAVE A MANUAL CONTROL AND AUTOMATIC CONTROL, SUCH AS A 24-HOUR CLOCK TIMER. 5.6 51 AT THE TIME OF THE FINAL INSPECTION, THE AUTOMATIC CONTROL SHALL BE SET TO OPERATE THE WHOLE -HOUSE FAN ACCORDING TO THE SCHEDULE USED TO CALCULATE THE WHOLE -HOUSE FAN SIZING. 53 A LABEL SHALL BE AFFIXED TO THE CONTROL THAT READS WHOLE HOUSE VENTILATION (SEE OPERATING INSTRUCTIONS)! M1501.3.2.1 OPERATING INSTRUCTIONS INSTALLERS SHALL PROVIDE THE MANUFACTURER'S INSTALLATION, OPERATING INSTRUCTIONS, AND A WHOLE -HOUSE VENTILATION SYSTEM OPERATION DESCRIPTION. M1501.3.3 MECHANICAL VENTILATION RATE THE WHOLE -HOUSE MECHANICAL VENTILATION SYSTEM SHALL PROVIDE OUTDOOR AIR TO EACH DWELLING UNIT AT A CONTINUOUS RATE OF NOT LESS THAN THAT DETERMINED IN ACCORDANCE WITH TABLE M15073.3(I). EXCEPTION: THE WHOLE -HOUSE MECHANICAL VENTILATION SYSTEM IS PERMITTED TO OPERATE INTERMITTENTLY WHERE THE SYSTEM HAS CONTROLS THAT ENABLE OPERATION FOR NOT LESS THAN 25 PERCENT OF EACH 4 -HOUR SEGMENT AND THE VENTILATION RATE PRESCRIBED IN TABLE M1507.3.30U IS MULTIPLIED BY THE FACTOR DETERMINED IN ACCORDANCE WITH TABLE M1507.3.3(2). M15013.5 WHOLE -NOUS€ VENTILATION INTEGRATED WITH A FORCED -AIR SYSTEM. THIS SECTION ESTABLISHES MINIMUM PRESCRIPTIVE REQUIREMENTS FOR WHOLE -HOUSE VENTILATION SYSTEMS INTEGRATED WITH FORCED -AIR VENTILATION SYSTEMS. A SYSTEM WHICH MEETS ALL THE REQUIREMENTS OF THIS SECTION SHALL BE DEEMED TO SATISFY THE REQUIREMENTS FOR A WHOLE -HOUSE VENTILATION SYSTEM. M15O1.3.5.1 INTEGRATED WHOLE -HOUSE VENTILATION SYSTEMS. INTEGRATED WHOLE HOUSE VENTILATION SYSTEMS SHALL PROVIDE OUTDOOR AIR AT THE RATE CALCULATED USING SECTION M1501.3.3. INTEGRATED WITH FORCED -AIR VENTILATION SYSTEMS SHALL DISTRIBUTE OUTDOOR AIR TO EACH HABITABLE SPACE THROUGH THE FORCED -AIR SYSTEM DUCTS. INTEGRATED FORCE -AIR VENTILATION SYSTEMS SHALL HAVE AN OUTDOOR AIR INLET DUCT CONNECTING A TERMINAL ELEMENT ON THE OUTSIDE OF THE BUILDING TO THE RETURN OF AIR PLENUM OF THE FORCED -AIR SYSTEM. AT A POINT WITHIN 4 FT UPSTREAM OF THE AIR HANDLER. THE OUTDOOR AIR INLET DUCT CONNECTION TO THE RETURN AIR STREAM SHALL BE LOCATED UPSTREAM OF THE FORCED -AIR SYSTEM BLOWER AND SHALL NOT BE CONNECTED DIRECTLY TO A FURNACE CABINET TO PREVENT THERMAL SHOCK TO THE HEAT EXCHANGER THE SYSTEM WILL BE EQUIPPED WITH A MOTORIZED DAMPER CONNECTED TO THE AUTOMATIC VENTILATION CONTROL AS SPECIFIED IN SECTION M501.3.2. THE REQUIRED FLOW RATE SHALL BE VERFIED BY FIELD TESTING WITH A FLOW HOOD OR A FLOW MEASURING STATION, M1501.3.5.2 VENTILATION DUCT INSULATION. ALL SUPPLY DUCTS IN THE CONDITIONED SPACE SHALL BE INSULATED TO A MINIMUM OF R-4, M1507.3.5.3 OUTDOOR AIR INLETS INLETS SHALL BE SCREENED OR OTHERWISE PROTECTED FROM ENTRY BY LEAVES OR OTHER MATERIAL. OUTDOOR AIR INLETS SHALL BE LOCATED SO AS NOT TO TAKE AIR FROM THE FOLLOWING AREAS: 1, CLOSER THAN 10 FT FROM AN APPLIANCE VENT OUTLET, UNLESS SUCH VENT OUTLET IS 3FT ABOVE THE OUTDOOR AIR INLET. 2, WHERE IT WILL PICK UP OBJECTIONABLE ODORS, FUMES OR FLAMMABLE VAPORS. 3_4 HAZARDOUS OR UNSANITARY LOCATION. 4_4 ROOM OR SPACE HAVING ANY FUEL -BURNING APPLIANCES THERIN. 5, CLOSER THAN 10 FT, FROM A VENT OPENING OF A PLUMBING DRAINAGE SYSTEM UNLESS THE VENT OPENING IS AT LEAST 3 FT ABOVE THE AIR INLET. 6, ATTIC, CRAWL SPACES, GARAGES. MI501.4 LOCAL EXHAUST LOCAL EXHAUST SHALL BE PROVIDED IN EACH KITCHEN, BATHROOM, WATER CLOSET, LAUNDRY ROOM, INDOOR SWIMMING POOL, SPA, AND OTHER ROOMS WHERE WATER VAPOR OR COOKING ODOR IS PRODUCED. LOCAL EXHAUST SYSTEMS SHALL BE DESIGNED TO HAVE THE CAPACITY TO EXHAUST THE MINIMUM AIR FLOW IRATE DETERMINED IN ACCORDANCE WITH THE TABLE M1501.4, M1501.4.1 LOCAL EXHAUST FANS EXHAUST FANS PROVIDING LOCAL EXHAUST SHALL HAVE A MINIMUM FAN FLOW RATING NOT LESS THAN 50 cfm AT 0.25 INCHES WATER GAUGE FOR BATHROOMS, LAUNDRIES, OR SIMILAR ROOMS AND 100 cFm AT 0.25 INCHES WATER GAUGE FOR KITCHENS. MANUFACTURERS' FAN FLOW RATINGS SHALL BE DETERMINED AS PER HVI 916 (APRIL 1995) OR AMCA 210, EXCEPTION: WHERE A RANGE HOOD OR DOWN DRAFT EXHAUST FAN IS USED TO SATISFY THE LOCAL EXHAUST REQUIREMENTS FOR KITCHENS, THE RANGE HOOD OR DOWN DRAFT EXHAUST SHALL NOT BE LESS THAN 100 cFm AT 0.10 INCHES WATER GAUGE, MI501.42 LOCAL EXHAUST CONTROLS LOCAL EXHAUST SYSTEMS SHALL BE CONTROLLED BY MANUAL SWITCHES, DEHUMIDISTATS, TIMERS OR OTHER APPROVED MEANS. LOCAL EXHAUST SYSTEM CONTROLS SHALL BE READILY ACCESSIBLE, MECHANICAL HEATING EQUIPMENT ALL WARM -AIR FURNACES SHALL BE LISTED AND LABELED BY AN APPROVED AGENCY AND INSTALLED TO LISTED SPECIFICATIONS. NO WARM -AIR FURNACES SHALL BE INSTALLED IN A ROOM USED OR DESIGNED TO BE USED AS A BEDROOM, BATHROOM, CLOSET OR IN ANY ENCLOSED SPACE WITH ACCESS ONLY THROUGH SUCH ROOM OR SPACE, EXCEPT DIRECT VENT FURNACE, ENCLOSED FURNACES AND ELECTRIC HEATING FURNACES. LIQUIFIED PETROLEUM GAS -BURNING APPLIANCES SHALL NOT BE INSTALLED IN A PIT, BASEMENT OR SIMILAR LOCATION WHERE HEAVIER THAN AIR GAS MIGHT COLLECT. APPLIANCES SO FUELED SHALL NOT BE INSTALLED IN AN ABOVE GRADE UNDER FLOOR SPACE OR BASEMENT UNLESS SUCH LOCATION IS PROVIDED WITH AN APPROVED MEANS FOR REMOVAL OF UNBURNED GAS. HEATING AND COOLING EQUIPMENT LOCATED IN A GARAGE WHICH GENERATES A GLOW, SPARK OR FLAME CAPABLE OF IGNITING FLAMMABLE VAPORS SHALL BE INSTALLED WITH THE PILOTS AND BURNERS FOR HEATING ELEMENTS AND SWITCHES AT LEAST 1S" ABOVE THE FLOOR LEVEL. TEMPERATUERE CONTROL THE PRIMARY SPACE CONDITIONING SYSTEM WITHIN EACH DWELLING UNIT SHALL BE PROVIDED WITH AT LEAST ONE PROGRAMMABLE THERMOSTAT FOR THE REGULATION OF TEMPERATURE WSEC 5EC.403.1.1 VENTILATION EVERY FACTORY BUILT CHIMNEY, TYPE L VENT, TYPE B GAS VENT OR TYPE BW GAS VENT SHALL BE INSTALLED IN ACCORDANCE WITH THE TERMS OF ITS LISTING, MFR'S INSTALLATION INSTRUCTIONS AND APPLICABLE CODE REQUIREMENTS. A TYPE L VENTING SYSTEM SHALL TERMINATE NOT LESS THAN 2 FEET ABOVE THE HIGHEST POINT WHERE THE VENT PASSES THROUGH THE ROOF OF THE BUILDING AND AT LEAST 2' HIGHER THAN ANY PORTION OF THE BUILDING WITHIN 10' OF THE VENT. UTILITY ROOM NOTES/MAKE UP AIR: 1. WHERE THE EXHAUST DUCT IS CONCEALED WITHIN THE BUILDING CONSTRUCTION, THE EQUIVALENT LENGTH OF THE EXHAUST DUCT SHALL BE IDENTIFIED ON A PERMANENT LABEL OR TAG. THE LABEL OR TAG SHALL BE LOCATED WITHIN 6 FEET OF THE EXHAUST DUCT CONNECTION. 2. INSTALLATIONS EXHAUSTING MORE THAN 200 CFM CHALL BE PROVIDED WITH MAKE UP AIR WHERE A CLOSET IS DESIGNED FOR THE INSTALLATION OF A CLOTHES DRYER, AN OPENING HAVING AN AREA OF NOT L€SS THAN 100 SQ. INCHES FOR MAKE UP AIR SHALL BE PROVIDED IN THE CLOSET ENCLOSURE, OR MAKE UP AIR SHALL BE PROVEDED BY OTHER APPR. MEANS. • 100 SQ INCH TRANSFER GRILL PER IRC 62439.4 (614.6) CONTINUOUS WHOLE -HOUSE MEC4IANICAL VENTILATIOIJ SYSTEM AIRFLOIII RATE RMWIREMENTB Dwelling Unit Floor Area (so. £t.) 0-1 2-3 Number of Bedrooms 4-5 Airflow in CFM 6-1 <1 ,1500 30 45 60 15 SO 1501 - 3000 45 00 15 so IID5 3001- 4500 6ID 15 90 105 120 4501 - 6000 15 90 105 120 135 6001 - 1500 eo 105 120 135 150 > 1500 105 120 135 150 165 INTERMITTENT II a F -410118E MECHANICAL VENTILATION RATE FACTORS Run -Time % in Each 4 -Hour Segment 25% 33% 50% 66 0 15% 100% Factor 4 3 2 1.5 1.3 10 MINR411 R90111RED HIMAUST RATES Area to be Vented Exhaust Rates Kitchens 100 cfm intermittent or zrrnnU - w Z 25 cfm cortimucusly Bathroom / Laundry / Similar 50 cfm intermittent or areas 20 cfm contimuously 0 F Z 0 Er p O W U LL W zrrnnU - w Z w U X of LL O Z ¢a W 10¢ W. LL W Z Z _ Z J O~ 0 �� W, 28 O W OU ¢o a LL- U~~ 20= W W = u-�LL W ~=(�72ioLL 0 Uj HLL' LL aa LL0 a W W o _ _ Q _ =0W LLO�1W� Kz W e F z ego o�o Z� a W W W w D of o_ 7 Z 0=0 F =o Z(7� ¢Zz ¢~O W of < Oo �o M n p - W Z U Z W iy aWo =F» �0 a2�Z viZUw zD ~ (op d LL w 20 X0 U¢ w O W:? F 0 LL N U O j a- wQ W,W7 UrdZ� Z w51 MF - W > m a H Z Q Z ¢Q~O Ir O¢ W� CZ7Y w ooQ� , N CLW= o� to W O ~ w ¢mal wag x�goi Fwa O11� O W W F ~ Z Y O¢ o N Z Z== �w~" H �¢oo H3 go W W> LL w LL U w a > a m' Q O m = LL ❑ T Z Z Z z_ 0 uwi p w W a¢ ao�W -1 g 'WoZ 0 z¢ m U W U= � W r a W 0U ¢ W 2 W U m w ZON3 N U a°OZ�Z a o0 W UBe,Z O w O W Z ¢tn w U faZ O a z¢ z z 0 a N_ QQ W� W of 20`n I=w 0❑ZZ O F �WUWQ� 0 CL aFoe Z� z a z. X UOrn1 D a D W W ofmof0 W [ E-1 I O O 00 Z N 07 N O 410 ap Qj J .-. J M w LO ■ ■ O C: '0 C: (1) CT3 O ^%, O [ E-1 I μ”C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/30/19 Job#: JM Lot-2 Eric L. Rice, PE07/01/19 C ERRORS OR OMISSIONS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/30/19 Job#: JM Lot-2 Eric L. Rice, PE07/01/19 C ERRORS OR OMISSIONS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/30/19 Job#: JM Lot-2 Eric L. Rice, PE07/01/19 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/30/19 Job#: JM Lot-2 Eric L. Rice, PE07/01/19 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/30/19 Job#: JM Lot-2 Eric L. Rice, PE07/01/19 C ERRORS OR OMISSIONS. FROM RUEPPELL, INC. WHICH RETAINS COPYRIGHTS TO, & OWNERSHIP OF THE PLANS. LIABILITIES THAT INCLUDE PENALTIES OF UP TO $20,000 PER WORK INFRINGES, AND UP TO $100,000 PER WORK INFRINGED WILLFULLY. ON LOAN BY THE CUSTOMER TO THIRD PARTIES NECESSARY TO ASSIST THE CUSTOMER IN USING THE PLANS, SUCH AS CONTRACTORS AND CONDITIONS OF LICENSE ACCEPTED BY THE CUSTOMER. USE OF ANY PART OF THE PLANS BY ANY PARTY OTHER THAN THE CUSTOMER, EXCEPT RUEPPELL, INC. PREPARES ITS PLANS CAREFULLY FOR THE USE OF ITS CUSTOMERS. HOWEVER, ADAPTATION OF THE PLANS TO MEET A GENERAL NOTE AND SPECIFICATIONS SHEET IS ALWAYS AN INTEGRAL PART OF THESE DRAWINGS AND GENERALLY THE LAST SHEET OF THE SET. UNAUTHORIZED USE OR COPYING OF THESE PLANS, OR THE DESIGN THEY DEPICT, INFRINGES RIGHTS UNDER THE COPYRIGHT ACT. INFRINGES FACE SPECIFIC STATE AND LOCAL BUILDING CODES AND REGULATIONS, AND SPECIFIC CONDITIONS, IS THE RESPONSIBILITY OF THE CONTRACTOR. IN ADDITION, SUBCONTRACTORS, IS STRICTLY PROHIBITED. THE PLANS MAY NOT BE RE-USED OR COPIED, IN WHOLE OR IN PART, WITHOUT WRITTEN PERMISSION RUEPPELL, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES RELATING TO THE ACCURACY AND OVERALL INTEGRITY OF THE PLANS IN EXCESS OF THE LICENSE PAID FOR THEIR USE. THE CONTRACTOR, THEREFORE, MUST CAREFULLY INSPECT ALL DIMENSIONS AND DETAILS IN THE PLANS FOR Copyright 2018, Rueppell, Inc.Drawn by: EL Revision Date: N/A Phone: (253) 297-8040 Plan: 3096 Date: 06/30/19 Job#: JM Lot-2 Eric L. Rice, PE07/01/19