The URL can be used to link to this page

SB 84311_Yelm & Killion_Cutsheets EquipmentProject ______________________________________ Item _________________________________________ Quantity ____________________________________ CSI Section 11400 Approved ___________________________________ Date _________________________________________ 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com 5880C_DEL 03/23 Exterior bottom shall be heavy-gauge galvanized metal. Exterior ends shall be heavy-gauge stainless steel. Exterior top shall be one-piece, heavy-gauge stainless steel with front edge turned down to form nosing and rear edge turned down. Base interior shall be one-piece thermoformed ABS plastic material, with integral shelf supports. ABS interior is backed by a limited lifetime warranty. Base shall be fully insulated with high-density foamed-in-place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane. Door shall have a heavy-gauge stainless steel exterior, with a thermoformed ABS plastic interior liner, and shall be fully insulated with foamed-in- place polyurethane. Door handle shall be black, recessed ABS. Cabinet shall have (2) adjustable epoxy-coated wire shelves installed. Refrigeration system shall use R290 refrigerant. Compressor shall be 1/5 h.p., with condenser coil and hot gas condensate evaporator mounted on rear of cabinet. Evaporator coil and temperature control shall be mounted on the interior rear wall of the cabinet. Refrigerant flow shall be controlled by a capillary tube. Cabinet shall maintain 36°F to 40°F (2°C to 4°C) interior cabinet temperature. Electrical connections shall be 115 volt, 60 Hertz, single phase. Unit shall have a 6’ (1.8m) long electrical cord and NEMA 5-15P plug. Cord and plug shall be located on rear of cabinet, 16” (40.6cm) above floor, 5” from the left side. Equipment is shipped with 2” (5cm) diameter casters installed. Specifications Standard Features Options & Accessories•Features Delfield’s exclusive ABS interior. ABS is extremely durable - It won’t dent, chip or corrode and is backed by a limited lifetime warranty •Stainless steel front, sides and top •Two epoxy coated wire shelves, standard installed per unit •Environmentally friendly R290 refrigerant •Foamed in place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane cuts energy costs •Black recessed quick grip handle •6’ cord and plug supplied •Door is field reversible with pre-drilled and plugged hinge-bolt locations. Standard hinging provided is on the right side •Three year parts and labor warranty and an additional two year compressor parts •406P-STAR2 - 115V Undercounter refrigerator single section on casters 400P Series 406P Self-Contained Compact Undercounter Refrigerator 40 0 P S e r i e s : 4 0 6 P S e l f - C o n t a i n e d C o m p a c t U n d e r c o u n t e r R e f r i g e r a t o r warranty R 406P-STAR2 Models 10267 - R290 model Welbilt reserves the right to make changes to the design or specifications without prior notice. 2" Polyex SwivalCasters W/ 150 Lb RatingFront W/ Brake Rear W/o BrakeQty-4 27.25” 69.2cm 32.00” 81.3cm 2.50”6.4cm 28.50” 72.4cm 1.00” 2.5cm 24.38”61.9cm Opening 22.62” 57.5cm Opening 6.00” 2.75” 3.75” 4.00” 17.05”43.3cm Depth 19.44” 49.4cm Depth A A 72” 183cm Nema Plug5-15p 115V units only 1.00” 2.5cm Clearance 3.00” 7.6cm Clearance 1.00” 2.5cm Clearance 16.00” 41cm Installation Note: Refrigeration system is designed so that air will flow under the unit, through the compressor area, and out the top rear of the unit. Any restriction to this air flow path will void the warranties. Side Clearances Front Elevation Front Elevation Interior Front Clearance Dimensions Side View Side Interior Standard Door Hinging Is On Right May be reversed to left in the field Door Clearance Detail Specifications Model V/Hz/Ph # of Shelves Shelf Area Volume H.P.Amps NEMA Plug Ship Weight Total Watts Energy (KWH/Day) 406P-STAR2 115/60/1 2 4.6ft2 5.7ft3 1/5 4.0 5-15P 168lbs (76kg)-1.16 40 0 P S e r i e s : 4 0 6 P S e l f - C o n t a i n e d C o m p a c t U n d e r c o u n t e r R e f r i g e r a t o r 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com 5880C_DEL 03/2310267 - R290 model Service Bulletin DELFIELD 980 SOUTH ISABELLA ROAD, MOUNT PLEASANT, MI 48858 844-724-CARE WWW.DELFIELD.COMA Welbilt Brand R 1. Use a screwdriver to remove the bottom hinge pin. 2. Tilt door out from bottom and slide top pin out of the hinge bracket. 3. Remove top hinge pin from door. 4. Use a putty knife or similar tool to remove top and bottom plugs from the alternate side to expose new hinge pin locations. Install the new plugs in original hinge pin locations. 5. Install the doors top hinge pin on new hinge side. Subject: Changing Door Orientation STARBUCKS MODELS WITH REHINGING OPTION For full length universal handle units 1 of 1 Document Number:9294257 10/22 6. Remove top and bottom hinge brackets from cabinet face. 7. Locate pre-drilled 1/8” holes on new hinge side and remove the factory installed plugs. 8. Fasten top and bottom hinge brackets in new locations. 9. Slide top door hinge pin into top hinge bracket and close door onto cabinet face. 10. Install bottom hinge pin through hinge bracket and into door. 10267 - R290 model Specifications subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number). ROUGH-IN DATA Model: Project Name: Location: Item #: Qty: Model #: AIA # SIS # TRUE MANUFACTURING CO., INC. U.S.A. FOODSERVICE DIVISION 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 Fax (636)272-2408 • Toll Free (800)325-6152 • Intl Fax# (001)636-272-7546 Parts Dept. (800)424-TRUE • Parts Dept. Fax# (636)272-9471 • www.truemfg.com Printed in U.S.A. APPROVALS:AVAILABLE AT: TUC-27-LP-HC Undercounter: Low Profile Solid Door Refrigerator with Hydrocarbon Refrigerant TUC-27-LP-HC Model Doors Shelves Cabinet Dimensions (inches) (mm)Counter Height HP Voltage Amps NEMA Config. Cord Length (total ft.) (total m) Crated Weight (lbs.) (kg)W D† H* TUC-27-LP-HC 1 2 275/8 301/8 293/4 317/8 1/6 115/60/1 2.0 5-15P 7 185 702 766 756 810 1/6 ▲2.13 84 † Depth does not include 1" (26 mm) for rear bumpers. * Height does not include 21/8” (54 mm) for low profile castors. ▲Plug type varies by country. INNOVATIONMADE WITH IN THE USA True’s undercounter units are designed with enduring quality that protects your long term investment. Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs, exceptional food safety and the best value in today’s food service marketplace. Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP). Energy Efficient, environmentally friendly forced-air refrigeration system holds 33°F to 38°F (.5°C to 3.3°C). All stainless steel front, top and ends. Corrosion resistant GalFan coated steel back. Interior - attractive, clear coated aluminum liner. Stainless steel floor with coved corners. Front breathing. Heavy duty PVC coated wire shelves. Foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP). Reverse hinging. 5/23 10267 STANDARD FEATURES Model: METRIC DIMENSIONS ROUNDED UP TO THENEAREST WHOLE MILLIMETER SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE PLAN VIEW KCL TRUE MANUFACTURING CO., INC. 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 • Fax (636)272-2408 • Toll Free (800)325-6152 • Intl. Fax# (001)636-272-7546 • www.truemfg.com ELEVATION 11/2" (39 mm) 71/2" (191 mm) 97/8" (251 mm) RIGHT VIEW 279/16" (701 mm) 2427/32" (632 mm) 5529/32" (1421 mm) 301/16" (764 mm) 21/8" (54 mm) 1" (26 mm) 293/4" (756 mm) 317/8" (810 mm) 5/8" (16 mm) TUC-27-LP-HC Undercounter: Solid Door Refrigerator with Hydrocarbon Refrigerant Model Elevation Right Plan 3D Back TUC-27-LP-HC TFQY01E TFQY01S TFQY01P TFQY013 DESIGN•True’s commitment to using the highest quality materials and oversized refrigeration systems provides the user with colder product temperatures, lower utility costs, exceptional food safety and the best value in today’s food service marketplace. REFRIGERATION SYSTEM•Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP).•Energy efficient, factory balanced refrigeration system with guided airflow to provide uniform product temperatures.•High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation.•State of the art, electronically commutated evaporator and condenser fan motors. ECM motors operate at higher peak efficiencies and move a more consistent volume of air which produces less heat, reduces energy consumption and provides greater motor reliability.•Condensing unit access in back of cabinet, slides out for easy maintenance. CABINET CONSTRUCTION•Exterior - stainless steel front, top and ends. Corrosion resistant GalFan coated steel back.•Interior - attractive, clear coated aluminum liner. Stainless steel floor with coved corners. •Insulation - entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP).•11/2" (39 mm) diameter dual swivel low profile castors permits easy placement. 317/8" (810 mm) work surface height. DOOR•Stainless steel exterior with clear aluminum liner to match cabinet interior.•Door fitted with 12" (305 mm) long recessed handle that is foamed-in-place with a sheet metal interlock to ensure permanent attachment.•Positive seal self-closing door with 90° stay open feature. Door swing within cabinet dimensions.•Magnetic door gasket of one piece construction, removable without tools for ease of cleaning.•Field reversible door. SHELVING•Two (2) adjustable, heavy duty PVC coated wire shelves. Top shelf is 231/4"L x 191/4"D (591 mm x 489 mm), bottom shelf is 231/4"L x 133/4"D (591 mm x 350 mm). Four (4) chrome plated shelf clips included per shelf.•Shelf support pilasters made of same material as cabinet interior; shelves are adjustable on 1/2" (13 mm) increments. MODEL FEATURES•Evaporator is epoxy coated to eliminate the potential of corrosion. •NSF/ANSI Standard 7 compliant for open food product. ELECTRICAL•Unit completely pre-wired at factory and ready for final connection to a 115/60/1 phase, 15 amp dedicated outlet. Cord and plug set included. OPTIONAL FEATURES/ACCESSORIES Upcharge and lead times may apply. ❑220-240V/50-60Hz ❑6" (153 mm) standard legs. ❑6" (153 mm) seismic/flanged legs. ❑21/2" (64 mm) diameter castors. ❑Barrel lock (factory installed). ❑Single overshelf. ❑Double overshelf. ❑TUC-27 Stacking collar. ❑30" (762 mm) deep,1/2 " (13 mm) thick, white polyethylene cutting board. Requires “L” brackets. ❑30" (762 mm) deep,1/2 " (13 mm) thick, composite cutting board. Requires “L” brackets. ❑Additional shelves. ❑Heavy duty, 16 gauge tops. ❑Exterior rectangular digital temperature display (factory installed). ❑ADA compliant models with 34" (864 mm) work surface height. ❑Field reversing hinge (U.S.A. and Canada only) 10267 TRUE CONTACTS NORTH AMERICA - CANADA AND CARIBBEAN UK, IRELAND, MIDDLE EAST, AFRICA AND INDIA EUROPEAN UNION AND COMMONWEALTH OF INDEPENDENT STATES AUSTRALIAMEXICO LATIN AMERICA Warranty Phone: +1 855 878 9277 Warranty Fax: +1 636 980 8510 Technical Phone: +1 855 372 1368 Warranty Email: warrantyinquiries@ truemfg.com Technical Email: service@truemfg.com 7:00-7:00 CST Monday-Thursday, 7:00-6:00 Friday, 8:00-12:00 Saturday Phone: +44 (0) 1709 888 080 UK Freephone: 0 800 783 2049 service-emea@truemfg.com 8:30am – 5:00pm M-F Phone: +49 (0) 7622 6883 0 service-emea@truemfg.com 8:00am – 5:00pm M-F Phone: +61 2 9618 9999 service-aus@truemfg.com 8:30am – 5:00pm M-F Phone: +52 555 804 6343/44 Toll Free in Mexico: 01 800 202 0687 service-mexicocity@truemfg.com 9:00am – 5:30pm M-F Phone: +56 232 13 3600 servicelatam@truemfg.com 9:00am – 5:30pm M-F PRODUCT ADVISEMENT TEC_WI_820 REV. A 05/4/2023 Page 1 of 2 BUILDING THE FINEST COMMERCIAL REFRIGERATION — True, “The Best of the Cold Ones” Model – TUC-27 EA • 10/19 Reversing the Door Swing Required Tools •1/4” Socket •5/16” Socket •3/8” Socket •Ratchet •1/4” Combo Wrench •Phillips Screwdriver •Putt y Knife •Hammer Step 1 With a socket, remove the lower hinge bracket from the cabinet (fig. 1). Then, remove the door. NOTE: Take care to not snap the upper hinge bushing (fig. 2). Fig. 1. Remove the lower hinge bracket. Step 2 Remove the cartridge hinge assembly from the door. See fig. 4. Step 3 With a putty knife, pry the square bushing from the door. Then, with a hammer, tap the bushing into the cartridge hinge’s original location. NOTE: When repositioning the bushing, gently tap it to prevent damage. Fig. 3. Move the bolts to the lower hinge bracket’s original location. Fig. 4. Remove the cartridge hinge assembly. Fig. 2. Do not snap the bushing on the top hinge. 10267 TRUEPRODUCT ADVISEMENT TEC_WI_820 REV. A 05/4/2023 Page 2 of 2 BUILDING THE FINEST COMMERCIAL REFRIGERATION — True, “The Best of the Cold Ones” Model – TUC-27 EA • 10/19 Reversing the Door Swing Step 6 With a putty knife, pry the cap and plastic bushing from the top of the door and swap their positions. Step 5 Rotate the hinge bracket (see fig. 5), and then secure the cartridge hinge assembly to the opposite side of the door. NOTE: Keep the washers in their original order. See fig. 6. Always angle the hinge bracket towards the center of the cabinet to keep tension on the spring. See fig. 7. Step 7 With a 1/4” socket, move the top hinge to the opposite side of the cabinet. See fig. 8. NOTE: Do not forget the hinge’s washers. Step 8 Install the door. 1.Position the door. NOTE: Take care to not snap the upper hinge bushing. See fig. 9. 2.Secure the lower hinge bracket to the unit. NOTE: Do not forget the hinge’s washers. See fig. 10. Check the door alignment while securing the hinge. Adjust the hinges as needed. To adjust the upper hinge, True recommends using a 1/4” combo wrench. Fig. 10. Do not forget the washers. INCORRECT CORRECT Fig. 7. Images show the front of the door facing up. A: Incorrect; hinge bracket has not been rotated and angles outward. B: Correct; hinge bracket has been rotated and angles inward towards the cabinet center; star-shaped hole keeps the correct spring tension. BA Fig. C. Remove the cartridge hinge assembly from the door. Fig.5. Remove the hinge bracket from the cartridge spring and then rotate it. Fig. 6. Keep the washers in their original order. Step 4 With a 5/16” socket, move the machine screws to the opposite side square bushing. Fig. 8. Do not forget the washers.Fig. 9. If needed, only use shallow angles when positioning the door. 10267 Specifications subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number). ROUGH-IN DATA Models: TRUE FOOD SERVICE EQUIPMENT, INC. Project Name: Location: Item #: Qty: Model #: AIA # SIS # Printed in U.S.A. APPROVALS:AVAILABLE AT: 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 Fax (636)272-2408 • Toll Free (800)325-6152 • Intl Fax# (001)636-272-7546 Parts Dept. (800)424-TRUE • Parts Dept. Fax# (636)272-9471 • www.truemfg.com 11/16 Model Doors Capacity (Cu. Ft.) (liters)Shelves Cabinet Dimensions (inches) (mm) HP Voltage Amps NEMA Config. Cord Length (total ft.) (total m) Crated Weight (lbs.) (kg)W D H* TG2R-2S-HC 2 56 8 51 3/8 34 5/8 78 1/4 1/3 115/60/1 5.6 5-15P 9 595 1586 1305 880 1988 N/A N/A 2.74 270 * Height does not include 4 1/4" (108 mm) for castors and 1/4" (7 mm) for system mechanical components. TG2R-2S-HC TG2R-2S-HC Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs and exceptional food safety. Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP). High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation. Stainless steel doors and front. Anodized quality aluminum exterior sides, back and bottom. NSF approved, clear aluminum interior sides and back liner. Stainless steel floor with coved corners. Adjustable, heavy duty PVC coated shelves. Positive seal self-closing door with 120° stay open feature. Lifetime guaranteed door hinges. Lifetime guaranteed recessed door handle. Entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP). TG2R-2S-HC TG Spec Series: Reach-In Solid Swing Door Refrigerator with Hydrocarbon Refrigerant TRUE REFRIGERATIONMADE IN SINCE 1945U.S.A. ® 11083 STANDARD FEATURES Model: METRIC DIMENSIONS ROUNDED UP TO THE NEAREST WHOLE MILLIMETER SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE PLAN VIEW TRUE FOOD SERVICE EQUIPMENT 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 • Fax (636)272-2408 • Toll Free (800)325-6152 • Intl. Fax# (001)636-272-7546 • www.truemfg.com WARRANTY Three year warranty on all parts & labor and an additional 4 year warranty on compressor.(U.S.A. only) Clip #4 goes in Hole 86 Clip #3 goes in Hole 62 12" (305 mm) 12" (305 mm) Clip #2 goes in Hole 38 Clip #1 goes in Hole 14 12" (305 mm) 12" (305 mm) 13" (331 mm) Ceiling of Cabinet Floor of Cabinet SHELVING INSTALLATION INCREMENTS See Diagram Below Starting at the bottom of the cabinet place the top of each shelf clip into the following holes: Clip #1 Hole 14 – this allows 13" (331 mm) from floor of cabinet to the top of this shelf. Clip #2 Hole 38 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf. Clip #3 Hole 62 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf. Clip #4 Hole 86 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf and 12" (305 mm) from the top of this shelf to the ceiling of the cabinet. DESIGN• True’s solid door reach-in’s are designed with enduring quality that protects your long term investment.• Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs and exceptional food safety. REFRIGERATION SYSTEM• Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP).• High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation.• State of the art, electronically commutated evaporator and condenser fan motors. ECM motors operate at higher peak efficiencies and move a more consistent volume of air which produces less heat, reduces energy consumption and provides greater motor reliability.• Top mounted refrigeration system with evaporator positioned out of food zone to maximize capacity. CABINET CONSTRUCTION• Exterior - stainless steel door and rainshield. Anodized quality aluminum sides, back and bottom.• Interior - NSF approved clear aluminum walls and back liner. Stainless steel floor with coved corners. • Insulation - entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP).• Welded, heavy duty steel frame rail, black powder coated for corrosion protection.• Frame rail fitted with 3 1/2 " (89 mm) diameter castors with locks provided on front set. DOOR• Stainless steel exterior. Door opens within cabinet dimension.• Door lock standard.• Lifetime guaranteed recessed door handle. Door fitted with 12" (305 mm) long recessed handle that is foamed-in-place with a sheet metal interlock to ensure permanent attachment.• Positive seal self-closing door with 120° stay open feature. Lifetime guaranteed door hinges.• Magnetic door gasket of one piece construction, removable without tools for ease of cleaning.• Raised interior door liner and recessed door gasket for additional gasket protection. SHELVING• TG2R-2S-HC Model - Eight (8) gray heavy duty PVC coated wire shelves 23 1/2 ” x 28 13/16 ” (597 mm x 732 mm). Four (4) shelf supports included per shelf (field installed). Shelves adjustable on 6” (153 mm) increments• Stainless steel shelf standards for additional shelf support. LIGHTING• LED interior lighting - safety shielded. MODEL FEATURES• Exterior digital temperature display, available with either °F or °C.• Evaporator epoxy coated to eliminate the potential of corrosion• NSF-7 compliant for open food product. ELECTRICAL• Unit completely pre-wired at factory and ready for final connection to a 115/60/1 phase, 15 amp dedicated outlet. 11 ft. power cord. TG2R-2S-HC TG Spec Series: Reach-In Solid Swing Door Refrigerator with Hydrocarbon Refrigerant PLAN VIEW ELEVATION 513/8" (1305 mm) 781/4" (1988 mm) 821/2" (2096 mm) 41/4" (108 mm) 513/8" (1305 mm) 345/8" (880 mm) 6111/32" (1559 mm) 2623/32" (679 mm) 11083 52.125 83.460 32.000 56.717 DUNNAGE RACK ON FLOOR SHELVES CAN BE ADJUSTED IN 1" INTERVALS NO SCALE SIZE DWG. NO.A REV. MATERIAL FINISH - -- DO NOT SCALE DRAWING DIMENSIONS ARE IN INCHES TOLERANCES: NAME DATE DRAWN CHECKED ENG APPR. MFG APPR. Q.A. SHEET 1 OF 1WEIGHT: 0 COMMENTS: THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL DATA OF TRAULSEN & CO. INC. NO DISCLOSURE, REPRODUCTION OR USE OF ANY PART THEREOF MAY BE MADE WITHOUT WRITTEN PERMISSION OF TRAULSEN & CO. INC. ANY VENDOR SUPPLYING PARTS UNDER THIS DRAWING AGREES NOT TO REVISE ANY PHYSICAL, DIMENSIONAL, MATERIAL OR PERFORMANCE CHARACTERISTICS OF SUCH PARTS AFTER APPROVAL BY TRAULSEN & CO. INC. GROUP OF VENDOR SAMPLES UNLESS AUTHORIZED IN WRITING BY TRAULSEN & CO. INC. PROPRIETARY AND CONFIDENTIAL G20010 B .XX .03 FRACTIONS 1/32.XXX .015 ANGLES 1/2HOLES .005 PARTS ARE TO FREE OF BURRS AND SHARP EDGES G-SERIES REFRIGERATOR K.TERASAKI 12/26/2018 G20010 11083 *AS PURCHASED THROUGH HOBART* 12618 12618 12618 Compact Undercounter Reversable Door Rehinging Instructions 12618 Compact Undercounter Reversable Door Rehinging Instructions 12618 Compact Undercounter Reversable Door Rehinging Instructions 12618 Compact Undercounter Reversable Door Rehinging Instructions 12618 Specifications subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number). ROUGH-IN DATA 2001 East Terra Lane • O’Fallon, Missouri 63366 (636)240-2400 • Fax (636)272-2408 • (800)325-6152 • Intl Fax# (001)636-272-7546 Parts Dept. (800)424-TRUE • Parts Dept. Fax# (636)272-9471 • www.truemfg.com Model: TRUE FOOD SERVICE EQUIPMENT, INC. Project Name: Location: Item #: Qty: Model #: AIA # SIS # Printed in U.S.A. APPROVALS:AVAILABLE AT: T-49F-HC STAR T-Series: Reach-In Solid Swing Door -10ºF Freezer with Hydrocarbon Refrigerant T-49F-HC STAR 8/16 Model Doors Shelves Cabinet Dimensions (inches) (mm) HP Voltage Amps NEMA Config. Cord Length (total ft.) (total m) Crated Weight (lbs.) (kg)L D H* T-49F-HC STAR 2 5 54 1/8 29 1/2 78 3/8 1 115/60/1 9.6 5-15P 9 440 1375 750 1991 1 230-240/50/1 5.5 ▲2.74 200 * Height does not include 5" (127 mm) for castors or 6" (153 mm) for optional legs.▲Plug type varies by country. TRUE REFRIGERATIONMADE IN SINCE 1945U.S.A. ® True’s solid door reach-in’s are designed with enduring quality that protects your long term investment. Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs, exceptional food safety and the best value in today’s food service marketplace. Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP). High capacity, factory balanced refrigeration system that maintains -10°F (-23.3°C) temperatures. Ideal for both frozen foods and ice cream. Stainless steel solid doors and front. The very finest stainless with higher tensile strength for fewer dents and scratches. Adjustable, heavy duty PVC coated shelves. Positive seal self-closing doors. Lifetime guaranteed door hinges and torsion type closure system. Automatic defrost system time-initiated, temperature-terminated. Saves energy consumption and provides shortest possible defrost cycle. Bottom mounted units feature: ”No stoop” lower shelf. Storage on top of cabinet. Compressor performs in coolest, most grease free area of kitchen. Easily accessible condenser coil for cleaning. 13682 STANDARD FEATURES Model: TRUE FOOD SERVICE EQUIPMENT 2001 East Terra Lane • O’Fallon, Missouri 63366 • (636)240-2400 • Fax (636)272-2408 • (800)325-6152 • Intl. Fax# (001)636-272-7546 • www.truemfg.com METRIC DIMENSIONS ROUNDED UP TO THENEAREST WHOLE MILLIMETER SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KCL PLAN VIEW T-49F-HC STAR ELEVATION PLAN VIEW 83 5/16" (2117 mm) 78 5/16" (1990 mm) 5" (127 mm) 54 1/8" (1375 mm) 29 1/2" (750 mm) 25 17/32" (649 mm) 55 1/32" (1398 mm) 13/8" (35 mm) 7615/16" (1955 mm) 4" (102 mm) T-Series: Reach-In Solid Swing Door -10ºF Freezer with Hydrocarbon Refrigerant Model Elevation Right Plan 3D Back T-49F-HC STAR WARRANTY Two year warranty on all parts and labor and an additional 3 year warranty on compressor. (U.S.A. only) SHELVING INSTALLATION INCREMENTSSee diagram below LEFT SIDE OF CABINET Clip #1 goes in Hole 28 from the bottom of the cabinet - this allows 17" (432mm) from the floor of cabinet to the top of this shelf. Clip #2 goes in Hole 59 from the bottom of the cabinet - this allows 17" (331mm) from the top of the shelf below to the top of this shelf. Clip #3 goes in Hole 76 from the bottom of the cabinet - this allows 9" (229mm) from the top of the shelf below to the top of this shelf and 11" (280mm) from the top of this shelf to the ceiling of the cabinet. Note: Measurements on left side of shelf standards are to top of shelves not the clips. Note: Hole numbers noted on right side of standard only include shelf clip slots and do not include holes for screws. RIGHT SIDE OF CABINET Clip #1 goes in Hole 28 from the bottom of the cabinet - this allows 17" (432mm) from the floor of cabinet to the top of this shelf. Clip #2 goes in Hole 59 from the bottom of the cabinet - this allows 17" (331mm) from the top of the shelf below to the top of this shelf and 20" (508mm) from the top of this shelf to the ceiling of the cabinet. Note: Measurements on left side of shelf standards are to top of shelves not the clips. Note: Hole numbers noted on right side of standard only include shelf clip slots and do not include holes for screws. CeilingLeft Side of Cabinet Right Side of Cabinet Clip #2 goes in Hole 59 (both sides) Clip #3 goes in Hole 76 (left side only) Clip #1 goes in Hole 28 (both sides) Floor of Cabinet 9" (229 mm) 17" (432 mm) 17" (432 mm) 17" (432 mm) 17" (432 mm) DESIGN• True’s commitment to using the highest quality materials and oversized refrigeration systems provides the user with colder product temperatures, lower utility costs, exceptional food safety and the best value in today’s food service marketplace. REFRIGERATION SYSTEM• Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP).• High capacity, factory balanced refrigeration system that maintains -10°F (-23.3°C) temperatures. Ideal for both frozen foods and ice cream.• State of the art, electronically commutated evaporator and condenser fan motors. ECM motors operate at higher peak efficiencies and move a more consistent volume of air which produces less heat, reduces energy consumption and provides greater motor reliability.• Bottom mounted condensing unit positioned for easy cleaning. Compressor runs in coolest and most grease free area of the kitchen. Allows for storage area on top of unit.• Automatic defrost system time-initiated, temperature-terminated. Saves energy consumption and provides shortest possible defrost cycle. CABINET CONSTRUCTION• Exterior - Stainless steel front. Anodized quality aluminum ends, back and top.• Interior - attractive, NSF approved, clear coated aluminum liner. Stainless steel floor with coved corners.• Insulation - entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP).• Welded, heavy duty steel frame rail, black powder coated for corrosion protection.• Frame rail fitted with 4" (102 mm) diameter stem castors - locks provided on front set. DOORS• Stainless steel exterior with clear aluminum liner to match cabinet interior. Doors extend full width of cabinet shell. Door locks standard.• Lifetime guaranteed recessed door handles. Each door fitted with 12" (305 mm) long recessed handle that is foamed-in-place with a sheet metal interlock to ensure permanent attachment.• Positive seal self-closing doors. Lifetime guaranteed door hinges and torsion type closure system.• Magnetic door gaskets of one piece construction, removable without tools for ease of cleaning. SHELVING• Five (5) adjustable, heavy duty PVC coated wire shelves 24 9/16 ”L x 22 3/8 ”D (624 mm x 569 mm). Four (4) chrome plated shelf clips included per shelf.• Shelf support pilasters made of same material as cabinet interior; shelves are adjustable on 1/2 " (13 mm) increments. LIGHTING• LED Interior lighting - safety shielded. Lights activated by rocker switch mounted above doors. MODEL FEATURES• Exterior temperature display.• Evaporator is epoxy coated to eliminate the potential of corrosion.• Rear airflow guards prevent product from blocking optimal airflow.• NSF-7 compliant for open food product. ELECTRICAL• Unit completely pre-wired at factory and ready for final connection to a 115/60/1 phase, 15 amp dedicated outlet. Cord and plug set included. 13682 The Future of Nitro Cold Brew is Here Nitro and Still Dispense The revolutionary technology infuses nitrogen instantly with no volume limitations. Pour as many servings as you like as fast as you possibly can with no deviation in quality. External nitrogen source needed (nitrogen generator or compressed nitrogen gas) Standalone Dispense System for Cold Brew Coffee A patented technology for nitrogenating cold brew coffee in-line and on-demand was created through years of research and development and a passion for quality dispensing methods. The result is JoeTap. You no longer need to wait several days while your cold brew coffee force-nitrogenates in a keg. Your JoeTap dispenser instantly transforms any cold brew coffee into nitro cold brew at the time of dispense. While the technology is sophisticated, the process is simple – Brew, Tap, Pour. 20010, 20011 Features Capacity: 2 x 10 liter corny kegs Product filter monitored and displayed to ensure beverage quality Simple weekly maintenance with reminder and lockout LED lighting inside the refrigerator to increase visibility Dispense tower can be mounted up to ten feet away from the refrigerator Specifications Dimensions 15" W x 28" H x 28.5" D Tower 17" H Nitro in (A) 1/4" OD John Guest (JG) 12' x 1/4" ID braided tube Nitrogen out 12' x 1/4" OD (JG) Cold brew out 12' x 3/8" ID braided tube (3/8" JG) Note: Nitrogen and cold brew lines bundled (B) in 2 1/2" OD closed cell tube insulation Refrigerant Butane Cord length 8' Approximate 80 lbs net weight Single- phase voltage Frequency (Hz) KW Plug Type Part Number Agency Approvals 115 50/60JT-NITCOM-R JT-NITCOM-L NSF-7, NSF -18, ETL 220 50/60 0.3 IEC C13 7" (178 mm) 1" (25.4 mm) 18" (457 mm) 3.5" min (89 mm) bend radius2.75" min (70 mm) bend radius A B 1" min (25.4 mm) clearance 1.5" (38 mm) 2.5" (64 mm) 17" (432 mm) 28.5" (724 mm)7/8" (22 mm)11" (279 mm) 7" (178 mm) 28.0" (711 mm) 15" (381 mm) Rev 22K25JoeTap855-4JoeTap | info@joetap.com | www.joetap.com JT-NITCOM-R-220 JT-NITCOM-L-220 0.3 IEC C13 NSF-7, NSF -18, JoeTap Equipment 2014/30/EU 2014/35/EU 20010, 20011 Installation and Calibration For Joe Tap Compact Nitro Coffee Dispensing Systems with the following Model Number: JT-NITCOM–(X) JoeTap 2 faucet COMpact NITro Coffee Dispensing System with Remote Dispensing Tower for one Nitrogenated coffee and one Cold brew coffee beverage. (X): L=Left Door Hinge, R = Right Door Hinge 115 V~, 60 Hz, 2.25 A CONTENTS PAGE NUMBER Safety and Warnings / Sécurité et Avertissements…... 2-3 Installation and System Requirements………………..…... 4-9 Calibration and Start-Up….………………………………..…..… 10 SERVICE AND FACTORY ASSISTANCE: Please record your Installer/Service Agent's name and phone number here for future reference: SERIAL NUMBER: ____________________ DATE OF INSTALLATION: ____________________ SERVICE AGENT NAME: ___________________ PHONE: _______________ PAGER: ______________ Service Assistance: call Wunder-Bar Joe Tap "Toll Free Service Hotline" @ 866-986-3372 anytime, or (707) 448-5151 Monday through Friday, 7:00 AM to 5:00 PM Pacific Time. JT Nitro Installation and Calibration Instructions 032219.pub !ATTENTION! JoeTap Cold Brew Coffee Dispensing Systems are NSF certified for the dispensing of Cold Brew Coffee with a pH greater than 5.0, ONLY. 20010, 20011 Automatic Bar Controls, Inc. •Read all Instructions before setting up or operating the dispenser. •This dispenser is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction. •Always disconnect the main power cord from the electrical source before removing any access panels or attempting to perform any servicing of this dispenser. •The dispenser should never be cleaned using a water jet nor installed in an area where a water jet is used. •Service access panels should be removed by qualified service technicians, ONLY. •Access to the service areas of this dispenser is restricted to qualified technicians with safety/hygiene knowledge, experience, and training for servicing this specific dispenser. •Install and use this dispenser only as described in this instruction manual. Read all Instructions before setting up or operating the dispenser. FCC Statement: This device complies with part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. IC Statement : This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. !ATTENTION! 2 •Lire toutes les instructions avant d'installer ou d'utiliser le distributeur. •Ce distributeur ne doit pas être utilisé par des personnes (y compris des enfants) ayant des capacités physiques, sensorielles ou mentales réduites ou un manque d'expérience ou de connaissances, à moins d'avoir reçu une supervision ou des instructions. •Toujours débrancher le cordon d'alimentation de la source électrique avant de retirer les panneaux d'accès ou de tenter d'effectuer toute intervention de ce distributeur. •Le distributeur ne doit jamais être nettoyé avec un jet d'eau, ni installé dans une zone où un jet d'eau est utilisé. •Panneaux d'accès aux services doivent être enlevés par des techniciens qualifiés, SEULEMENT. •Accès aux zones de service de ce distributeur est limitée à des techniciens qualifiés de la sécurité / des connaissances d'hygiène, l'expérience et la formation pour l'entretien de ce distributeur spécifique. •Installer et utiliser ce distributeur tel que décrit dans ce manuel d'instruction. Utilisez uniquement du fabricant les accessoires recommandés par. Déclaration IC: Cet appareil est conforme aux normes RSS sans licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences pouvant provoquer un fonctionnement non désiré de l'appareil. •Read all Instructions before setting up or operating the dispenser. •This dispenser is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction. •Always disconnect the main power cord from the electrical source before removing any access panels or attempting to perform any servicing of this dispenser. •The dispenser should never be cleaned using a water jet nor installed in an area where a water jet is used. •Service access panels should be removed by qualified service technicians, ONLY. •Access to the service areas of this dispenser is restricted to qualified technicians with safety/hygiene knowledge, experience, and training for servicing this specific dispenser. •Install and use this dispenser only as described in this instruction manual. Read all Instructions before setting up or operating the dispenser. FCC Statement: This device complies with part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. IC Statement : This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. !ATTENTION! 2 •Lire toutes les instructions avant d'installer ou d'utiliser le distributeur. •Ce distributeur ne doit pas être utilisé par des personnes (y compris des enfants) ayant des capacités physiques, sensorielles ou mentales réduites ou un manque d'expérience ou de connaissances, à moins d'avoir reçu une supervision ou des instructions. •Toujours débrancher le cordon d'alimentation de la source électrique avant de retirer les panneaux d'accès ou de tenter d'effectuer toute intervention de ce distributeur. •Le distributeur ne doit jamais être nettoyé avec un jet d'eau, ni installé dans une zone où un jet d'eau est utilisé. •Panneaux d'accès aux services doivent être enlevés par des techniciens qualifiés, SEULEMENT. •Accès aux zones de service de ce distributeur est limitée à des techniciens qualifiés de la sécurité / des connaissances d'hygiène, l'expérience et la formation pour l'entretien de ce distributeur spécifique. •Installer et utiliser ce distributeur tel que décrit dans ce manuel d'instruction. Utilisez uniquement du fabricant les accessoires recommandés par. Déclaration IC: Cet appareil est conforme aux normes RSS sans licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences pouvant provoquer un fonctionnement non désiré de l'appareil. 20010, 20011 Automatic Bar Controls, Inc. SAFETY AND ENVIRONMENTAL RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. DO NOT USE MECHANI- CAL DEVICES TO DEFROST REFRIGERATOR. DO NOT PUNCTURE REFRIGERANT TUBING. RISQUE D'INCENDIE OU D'EXPLOSION. RÉFRI- GÉRANT INFLAMMABLE UTILISÉ. NE PAS UTI- LISER DE DISPOSITIFS MÉCANIQUES POUR DÉ- GIVRER LE RÉFRIGÉRATEUR. NE PAS PERCER DE TUBAGE DE RÉFRIGÉRANT. REFRIGERATION COMPONENT PARTS SHALL BE REPLACED WITH LIKE COMPONENTS AND SERVICING MUST BE DONE BY FACTORY AU- THORIZED SERVICE PERSONNEL, ONLY, TO MINIMIZE THE RISK OF POSSIBLE IGNITION DUE TO INCORRECT PARTS OR IMPROPER SERVICE. LES COMPOSANTS DOIVENT ÊTRE REMPLACÉS PAR DES COMPOSANTS SIMILAIRES. L'ENTRE- TIEN DOIT ÊTRE EFFECTUÉ PAR LE PERSON- NEL D'ENTRETIEN AUTORISÉ PAR L'USINE UNIQUEMENT POUR MINIMISER LE RISQUE D'ALLUMAGE POSSIBLE EN RAISON DE PIÈCES INCORRECTES OU D'UN SERVICE INCORRECT. RISK OF ELECTRIC SHOCK! IF THE CORD OR PLUG BECOMES DAMAGED, REPLACE ONLY WITH A CORD AND PLUG OF THE SAME TYPE AND RATING. RISQUE DE CHOC ELECTRIQUE! SI LE CORDON OU LA FICHE DEVIENT ENDOMMAGÉS, NE LE REMPLACEZ QUE PAR UN CORDON ET UNE FICHE DU MÊME TYPE ET DE LA QUALITÉ. RISK OF ELECTRIC SHOCK! DO NOT OPER- ATE THE SYSTEM WITH A DAMAGED POW- ER CORD OR IF THE EQUIPMENT HAS BEEN DAMAGED OR DROPPED —UNTIL IT HAS BEEN EXAMINED BY AN AUTHORIZED SER- VICE PERSON. RISQUE DE CHOC ELECTRIQUE! NE FAITES PAS FONCTIONNER LE SYSTÈME AVEC UN CORDON D'ALIMENTATION ENDOMMAGÉ OU SI L'ÉQUIPEMENT A ÉTÉ ENDOMMAGÉ OU S'ÉCHUTE - JUSQU'À CE QU'IL SOIT EX- AMINÉ PAR UNE PERSONNE DE SERVICE AUTORISÉE. THIS SYSTEM IS INTENDED FOR INDOOR INSTALLATION AND OPERATION ONLY. THIS SYSTEM IS DESIGNED TO OPERATE BETWEEN 50°F (10°C) AND 100°F (38°C). FOR BEST RE- SULTS KEEP UNIT OUT OF DIRECT SUNLIGHT. CE SYSTÈME EST CONÇU POUR UNE INSTALLA- TION À L'INTÉRIEUR ET UN FONCTIONNEMENT UNIQUEMENT. CE SYSTÈME EST CONÇU POUR FONCTIONNER ENTRE 50 ° F (10 ° C) ET 100 ° F (38 ° C). POUR DE MEILLEURS RÉSULTATS, CONSERVER L'UNITÉ HORS DU SOLEIL DIRECT. 3 20010, 20011 Automatic Bar Controls, Inc. 4 These instructions outline the steps involved in installing the JoeTap™ Refrigeration Unit and Infusion Tower. •Uncrating the JoeTap™ nitro coffee system •Installing the Refrigeration Unit •Routing the product lines •Installing the JoeTap™ Infusion Tower onto the countertop •Calibration and Start-up procedures Tools & Materials Required: •Product Quality Specification •Number 2 Phillips Screw Driver •Crescent Wrench •Oetiker Clamp crimping Pliers •Tubing Cutter •Electric Drill •3” Hole Saw •1 3/8” Hole Saw •1/4" Drill Bit •Metal Hacksaw •Black or Clear RTV Silicone Sealant •2.5 Gallon Corny Keg filled with product •3” ABS Plastic Pipe (Optional-See step 3 in Bar Top Installation Instructions) •Pipe Cutter (Optional-See step 3 in Bar Top Installation Instructions) Items Included with JoeTap™ Refrigeration Unit: Drip Tray Box Contents: •120 VAC Power Cord •Drip Tray (Includes Drip Tray, Perforated Insert, Washer, and Nut) •1/4” Barb x 3/8” Stem (John Guest) Fitting with three 12.3 Oetiker clamps •Tower / Drip Tray Mounting Template •3/8” and 1/4” Locking Clips for John Guest Fittings •Kay 5 Cleaning Solution and Cleaning Y-Tube Assembly •JoeTap™ Tower with Mounting Hardware [Bracket, Gasket, (4)10-24 x 2-1/2” Bolts, (4) Washers, and (4) Nuts] •Tower Tubing Bundle (Black Insulated Bundle) Tower Box Contents: •2 JoeTap™ Dispenser Tap Handles •Installation, Operation, and Cleaning Instructions Uncrating and Assembly: 1.Remove the banding securing the shipping carton to the pallet. 2.Unpack the Refrigeration Unit. 3.Open the Refrigeration Unit’s door and remove the “Tower Box” and the “Drip Tray Box” set them aside. 4.Inspect the “Drip Tray Box” to ensure that all parts listed above in “Items Included with JoeTap Refrigeration Unit” are present and undamaged. Inspect the Tower to confirm that both faucets are present and not damaged. Installation Instructions 20010, 20011 Automatic Bar Controls, Inc. 5 1.Remove the Refrigeration Unit from its packaging. 2.Connect Power Cord to the Socket located in the center of the bottom rear of the Refrigeration Unit. 3.Roll the refrigerator to its preferred location. NOTE: The following minimum clearances are required! Detail A—Product lines to tower = Minimum 3.05” (77.5mm) Detail B—Nitrogen Line = Minimum 2.06” (52.3mm) Rear of Refrigerator Clearance = Minimum 1.0” (25.4mm) 2.Rout the product line bundle to the location where the bar top dispense tower will be installed. 3.Rout the nitrogen line to the nitrogen source. 4.Plug the refrigerator into 115VAC NEMA 5-15 receptacle and roll it into place. Assembling and Installing the Refrigeration Unit: 20010, 20011 Automatic Bar Controls, Inc. 6 Installation Instructions (continued) Bar Top Tower Installation: 1.Use the JoeTap™ laminated mounting template included with each JoeTap™ dispensing system to mark and drill the mounting holes for the JoeTap™ Infusion Tower (3” diameter), Tower Mounting Bolts (4 X 1/4” diameter) and drain pan Drain (1-3/8” diameter) (see Figure 1). 2.Place the included Tower Gasket on the counter top, aligned with the four ¼” Bolt holes in the countertop. Place the JoeTap Infusion Tower over the Gasket, with the four mounting holes in the Tower Gasket, JoeTap™ Infusion Tower, and the counter top aligned. 3.NOTE: If the countertop is made of laminated wood, place a 3” OD piece of plastic pipe, cut to the same length as the countertop’s finished (laminated) thickness, into the 3” hole that was cut for the Tower tubing to pass through. 4.Install, two each, of the provided 10-24 x 2 ½” Bolts, Nuts, and Washers into the front right and back left holes. 5.Route the black insulated Tubing Bundle to the underside of the JoeTap™ Infusion Tower. Cut the tubing to proper length. Note: Ensure tubing end cuts are at 90 degrees to ensure a proper seal in the tower fittings) Allow three extra feet of insulated tubing length to insure you can pull refrigerator forward for cleaning. 6.Measure and cut the clear braided tubing and the white tubing so that the two tubes can plug into the tower without causing unnecessary bends. A.Insert the ¼” barbed end of the gray Barb-Stem Union Fitting, provided, into the end of the Clear Braided Tubing (protruding from the end of the Tubing Bundle). Do not install the Clamp yet! (See Figure 2, page 5) Push the stem end of the same fitting into the 2-Way Divider fitting that protrudes from the bottom of the JoeTap™ Infusion Tower. Make sure the gray Stem is fully inserted into the 2 -Way Divider’s Inlet. B.Insert the end of the White Tube into the Check Valve located at the bottom of JoeTap Infusion Tower to check if attaching it causes any bends in the Clear Braided tubing; if there are unnecessary bends, cut the white tube again to proper length. C.Remove the tubes from the tower to install the Tower Bracket. Figure 20010, 20011 Automatic Bar Controls, Inc. Figure 2 Clear Braided Tubing Gray stem end of Barb-Stem Union Barbed End of the Barb- Stem Union Installed into the Braided Tubing Two-Way Divider Fitting Inlet Check Valve White LLDPE Tubing Figure 3 Tower Bracket White LLDPE Small Strain Re-Large Strain Re- Clear Braided 12.3 Oetiker Clamp Gray Stem end of Barb-Stem Union 7.Once the tubes are cut to proper lengths push them through the two Strain Relief (Cord Grips) installed into the Tower Bracket (Figure 3). The Small Strain Relief, with the light gray rubber sleeve insert, is for the White LLDPE Tubing. The Large Strain Relief, with the bigger hole and no Sleeve, is for the Clear Braided Tubing with installed Barb-Stem Union Fitting. A.Insert the Clear Braided Tubing so that the threaded portion on the cord grip attached to Tower Bracket is facing away from the insulation on the Tubing Bundle (see Figure 3). B.After both Tubes are pushed through the Strain Releifs, install the provided Clamp over the Barb -Stem Union and onto the end of the Clear Braided Tubing and the secure the Oetiker Clamp with a crimping pliers. 7 Installation Instructions (continued) Bar Top Tower Installation: 20010, 20011 Automatic Bar Controls, Inc. Installation Instructions (continued) Bar Top Tower Installation: Figure 4 8.Insert the stem end of the Barb Stem Union Fitting, attached to the Clear Braided Tubing, into the 2 -Way Divider fitting located at the bottom of the JoeTap™ Infusion Tower. Make sure the stem is fully inserted into the 2-Way Divider’s inlet (see Figure 4). Insert the White LLDPE Tubing into the Check Valve at bottom of JoeTap™ Infusion Tower making sure the tube is fully inserted in the Check Valve. 9.Insert the provided 3/8” Red Locking Clip into the 2 -Way Divider’s Lock-Ring where the Barb Stem Union Fitting attached to Clear Braided Tubing was inserted (see Figure 4). 10.Insert the provided ¼” Red Locking Clip into the Check Valve’s Lock -Ring where the White LLDPE Tubing was inserted (see Figure 4). 11.Position the Tower Bracket so the Bracket’s two mounting holes are align with the remaining two ¼” holes in the countertop. Install the two remaining, provided, 10 -24x2 ½” Bolts, Nuts, and Washers through the remaining mounting holes located in the JoeTap™ Infusion Tower, countertop, and Tower Bracket (as shown in Figure 4). After tightening all four Mounting Nuts, use a hack saw to cut the remaining exposed bolt to 2 -1/2 threads or less. 12.Tighten the Knobs on both the Strain Reliefs attached to the Tower Bracket so the Strain Reliefs grasp the hoses routed through them. Lightly pull on the hoses to make sure the tubes have been properly anchored, if either moves freely, tighten the knob on that strain relief more to increase the gripping strength. Check Valve Clear Braided Tubing Two-Way Divider Fitting Inlet White LLDPE Tubing 1/4” Red Locking Clip 3/8” Red Locking Clip Large Strain Relief Knob Small Strain Relief Knob 8 20010, 20011 Automatic Bar Controls, Inc. Installation Instructions (continued) Bar Top Tower Installation: 9 Figure 5 13.Install the provided Tap Handles onto the two faucets included with the JoeTap™ Infusion Tower (see Figure 5). Bar Top Drain Installation: Figure 6 Figure 7 1.Insert the Drip Tray’s threaded Tailpiece through the 1 3/8” hole made using the Tower Mounting Template during the Bar Top Tower Installation step 1 on page 4 of this manual (see Figure 6). 2.Install the provided 1-1/4” Washer onto the Drip Tray’s threaded Tailpiece from under the countertop (as shown in Figure 7). 3.Install the provided Hex Nut onto the Drip Tray’s threaded Tailpiece. Adjust the orientation of the Drip Tray so the two faucets on the JoeTap™ Infusion Tower are positioned directly over the centers of the two holes located in the drip tray Insert. Once the faucets are aligned, apply a small bead of black or clear RTV silicone sealant around the entire perimeter of the Drip Tray’s bottom edge (rim). 20010, 20011 Automatic Bar Controls, Inc. 10 System Calibration 1.Once the tower is installed: 2.Connect the ¼” ID tubing to the nitrogen generator or nitrogen tank. Fitting and nitrogen sup- ply provided by others. 3.Turn on the nitrogen generator or open the nitrogen tank valve and wait for it to build to oper- ating pressure. 4.Once the generator has achieved full pressure, adjust the pre-filter nitrogen regulator to 40psi. Assure the faucets are closed. 5.Connect the black Product (ball lock) Connector to the Product Tank fitting that is labeled “OUT” by pulling the black Connector’s flanged Lock Ring upward fully while pushing the black Connector onto the product tank fitting labeled “OUT” fully and then release the black Connector’s lock ring. Pull up on the black Connector to confirm that it is securely latched onto the “OUT” tank connection. 6.Connect the gray Gas (Ball Lock) Connector to the Product Tank fitting that is labeled “IN” by pulling the gray Connector’s flanged Lock Ring upward fully while pushing the gray Connector onto the product tank fitting labeled “IN” fully and then release the gray Connector’s lock ring. Pull up on the gray Connector to confirm that it is securely latched onto the “IN” tank System Start-Up 1.Pull the secondary regulator’s black knob (labelled “Nitrogen Out”) Upward until a slight click is felt, indicating that the regulator is in adjustment mode. Set the pressure to 9psi using the Nitrogen Pressure readout on the touchscreen. Increase the pressure by turning the knob clockwise. Decrease the pressure by turning the knob counterclockwise. 2.Place a 16oz clear plastic “cold beverage” cup under the nitro faucet. Open nitro faucet until product starts pouring. Close the faucet. 3.Place a serving cup under the nitro faucet and pour a full product serving into the cup. Ob- serve the cascade and head size. Use the Product Quality Specification to determine product acceptability. 4.If there is less/more nitro effect than desired, adjust the black knob on the regulator labelled “Nitrogen Pre-Filter” to increase or decrease the nitro effect. Increasing pressure will increase the cascading and foam height. 5.Continue adjusting and pouring until the level of nitro meets your requirements. Once you have found the desired level of nitrogenation, push the black knob in to lock it in place. Ad- justments can be made at any time. Calibration and Start-Up Instructions 20010, 20011 Automatic Bar Controls, Inc. Operators Guide For Joe Tap Compact Nitro Coffee Dispensing Systems with the following Model Number: JT-NITCOM–(X) JoeTap 2 faucet COMpact NITro Coffee Dispensing System with Remote Dispensing Tower for one Nitrogenated coffee and one Cold brew coffee beverage. (X): L=Left Door Hinge, R = Right Door Hinge 115 V~, 60 Hz, 2.25 A CONTENTS PAGE NUMBER Cleaning & Maintenance-Daily Filter Cleaning……….... 2-7 Cleaning & Maintenance-Daily Tap & Font Cleaning... 8-10 Cleaning & Maintenance-Weekly System Cleaning….. 11-17 Troubleshooting…………………………………………………..…. 18-19 Service Assistance: call Wunder-Bar Joe Tap "Toll Free Service Hotline" @ 866-986-3372 anytime, or (707) 448-5151 Monday through Friday, 7:00 AM to 5:00 PM Pacific Time. JT Nitro Operators Guide 030819.pub !ATTENTION! JoeTap Cold Brew Coffee Dispensing Systems are NSF certified for the dispensing of Cold Brew Coffee with a pH greater than 5.0, ONLY. 20010, 20011 Automatic Bar Controls, Inc. 10 The Joe Tap system is equipped with a filter and faucets that will require cleaning one or more times per day (see below). In addition, the entire system must be cleaned once weekly to ensure optimal system performance (page 18, Weekly Cleaning). Daily Filter Cleaning The JoeTap system is equipped with a filter installed in the output line leading from the keg. This filter must be re- moved and cleaned daily to ensure optimal system performance. The unit is equipped with a timer that will alert the user that the daily filter cleaning is due. To start the filter cleaning procedure, select “Cleaning” (Figure 8) on the touchscreen and then select “Filter Cleaning” (Figure 9). Cleaning and Maintenance Figure 8 Figure 9 20010, 20011 Automatic Bar Controls, Inc. Daily Filter Cleaning (Continued) 11 Figure 11 Figure 10 Figure 12 20010, 20011 Automatic Bar Controls, Inc. 12 Figure 12 Figure 13 Daily Filter Cleaning (Continued) Figure 14 Figure 15 20010, 20011 Automatic Bar Controls, Inc. 13 Figure 16 Daily Filter Cleaning (Continued) Figure 17 Figure 18 20010, 20011 Automatic Bar Controls, Inc. Daily Filter Cleaning (Continued) 14 Figure 19 Figure 20 Figure 21 20010, 20011 Automatic Bar Controls, Inc. 15 Daily Filter Cleaning (Continued) Figure 22 20010, 20011 Automatic Bar Controls, Inc. 16 Daily Cleaning “Tap & Font” The JoeTap system requires daily cleaning of the dispense taps and drain area. The system is equipped with a timer that will alert the user that the daily tap and font cleaning is required. To start the tap and font cleaning procedure, select “Cleaning” (Figure 23) on the touchscreen and then select “Tap & Font Cleaning” (Figure 24). Figure 24 Figure 23 Figure 25 20010, 20011 Automatic Bar Controls, Inc. 17 Daily Cleaning “Tap & Font” (Continued) Figure 26 Figure 27 Figure 28 20010, 20011 Automatic Bar Controls, Inc. 18 Daily Cleaning “Tap & Font” (Continued) Figure 29 Figure 30 20010, 20011 Automatic Bar Controls, Inc. 19 Weekly Cleaning The JoeTap system is equipped with a timer that will alert the user that the weekly cleaning is required. The system will be disabled if the weekly cleaning procedure is not performed. To ensure optimal system performance, perform the following cleaning procedure once a week. To start the weekly cleaning procedure, select “Cleaning” on the touchscreen (see Figure 31) and then select “Beverage Line Cleaning” (see Figure 32). PREPARATION FOR WEEKLY CLEANING CLEANING SOLUTION: Use a Sanitizing Solution capable of providing 100 PPM of available chlorine when properly mixed with warm (approximately 100°F /38°C) water such as KAY 5® chlorinating sanitzer available from Kay Chemicals in 1 ounce packets. Or, use other Sanitizing Solutions that provide 100 PPM available chlorine solution when mixed per the man- ufacturer’s instructions, with 100°F /38°C potable water. CLEANING SOLUTION PREPARATION: KAY 5®: Mix One, 1 ounce packet of Kay 5® sanitizer powder with 2 -1/2 gallons / 9-1/2 liters of 100°F / 38°C water in a clean product tank. Other Sanitizing Solutions: Mix the recommended amount of sanitizing solution or powder (per instructions) with 2-1/2 gallons of 100°F / 38°C water to achieve a 100 PPM concentration of available Chlorine, in a clean product tank. Install the product tank lid before attaching to the system . Figure 31 Figure 32 20010, 20011 Automatic Bar Controls, Inc. 20 Weekly Cleaning (Continued) Figure 34 Figure 33 Figure 35 Note: See Cleaning Solution Prepara- tion Instructions on page 19. 20010, 20011 Automatic Bar Controls, Inc. 21 Weekly Cleaning (Continued) Figure 38 Figure 37 Figure 36 20010, 20011 Automatic Bar Controls, Inc. 22 Weekly Cleaning (Continued) Figure 41 Figure 40 Figure 39 WASH DWELL (SOAK) 20010, 20011 Automatic Bar Controls, Inc. 23 Weekly Cleaning (Continued) Figure 43 Figure 44 Figure 42 RINSE AND SANITIZE 20010, 20011 Automatic Bar Controls, Inc. 24 Weekly Cleaning (Continued) Figure 46 Figure 45 Figure 47 20010, 20011 Automatic Bar Controls, Inc. 25 Weekly Cleaning (Continued) Figure 48 Figure 49 20010, 20011 Automatic Bar Controls, Inc. Troubleshooting Select “Machine Info” – Look for pressure readings that are out of the nominal range . Nominal Display Readings MACHINE SYMPTOM WHAT TO DO Display is blank Make sure the power cord is plugged into the wall receptacle Make sure wall receptacle has power Unplug the power cord for 5 minutes and plug it back in. 40.0 38.4 9.0 Pressure Name Nominal Range Pre-Filter PSI: 38-42 PSI Post-Filter PSI: 36-42 PSI Nitrogen PSI: 7-10 PSI 26 20010, 20011 Automatic Bar Controls, Inc. 27 Troubleshooting (continued) DISPLAYED MESSAGE WHAT TO DO LOCKOUT Run the weekly cleaning cycle LOW PRESSURE Make sure the coffee keg is connected Clean the filter CLEANING DUE Run the weekly cleaning cycle soon MACHINE SYMPTOM WHAT TO DO NO PRODUCT FLOW Check for empty coffee keg in the refrigeration unit Make sure the coffee keg is connected Clean the filter NITRO COFFEE IS FOAMY Run the weekly cleaning cycle Check for nominal Pressure Readings NITRO COFFEE IS FLAT Check for nominal Pressure Readings Run the weekly cleaning cycle DISPENSE RATE IS SLOW Clean the filter Run the weekly cleaning cycle 20010, 20011 Automatic Bar Controls, Inc. retail grinder KR 1203 Fast and reliable 10808 Ditting Maschinen AG Bramenstrasse 11 | CH-8184 Bachenbülach | Switzerland Phone +41 44 864 18 00 | Fax + 41 44 864 18 01 info@dittingswiss.ch | www.dittingswiss.ch TECHNICAL DATA Voltage/frequency/phase Motor power Rotor current drain Average grinding capacity Hopper capacity Grinding disc diameter Ø Net weight Dimensions (w x d x h) Standard colour Certiﬁ cations EQUIPMENT Available versions Hopper magnet Manual bag holding device Bag shaker Cooling fan Overload protection SPECIAL EQUIPMENT Special grinding discs Special colours Other electric specifications available on request 1203 110-120 V / 60 Hz / 1 1.4 kW / 1.9 hp 13 amps 1400 g/min / 3 lbs/min 1100 g / 2.4 lbs 120 mm 38 kg / 94 lbs 260 x 340 x 640 mm / 10.23“ x 13.39“ x 25.2“ black, stainless steel UL, cUL, ETL (NSF-8) KR • • • • • – • 1403 220 V / 60 Hz / 3 1.7 kW / 2.3 hp 10.7 amps 2200 g / 5 lbs/min 1100 g / 2.4 lbs 140 mm 38 kg / 94 lbs 260 x 340 x 640 mm black, stainless steel UL, cUL, ETL (NSF-8) KR • • • • • • • The 1203 and 1403 models are the ideal solution everywhere that fast, reliable and uniform grinding is required. Coffee stores with a large volume of business, supermarkets and roasting establishments value these coffee grinders highly for their exceptional performance, sturdiness and simple and safe operation. • Specially developed motors allowing large grinding capacity at all degrees of fineness. • Preservation of coffee’s unique aromatic oils thanks to uniform, gentle and cool grinding made possible by specially sharpened discs developed by Ditting. • Continuously variable adjustment of grinding fineness. • Minimal coffee particles left in discharge tube thanks to built-in vibrating device or manual tapper. • Efficient bag shaking device distributes grounds evenly into bag and ensures all particles are dispensed. • Precision grinding discs made of high quality material that is extremely wear resistant. The original discs can be re-sharpened up to 3 times with proper care and maintenance. • Easy to maintain and clean. retail grinder KR 1203/1403 Ditting USA, Inc. 8801-B Smiths Creek Rd | Wales, Michigan 48027 | USA Phone +1 810 367 7125 | Fax +1 810 367 7130 Phone 800 835 5992 | www.ditting.com10808 Ditting Maschinen AG Länggenstrasse 34 | CH-8184 Bachenbülach | Switzerland Phone +41 44 864 18 00 | Fax + 41 44 864 18 01 info@dittingswiss.ch | www.dittingswiss.ch TECHNICAL DATA Voltage/frequency/phase Motor power Average grinding capacity Hopper capacity Grinding disc diameter Ø Shaker plate Sticker Ditting Basic Adjustment Net weight Dimensions (w x d x h), mm Standard colour EQUIPMENT Hopper magnet Automatic bag holding device Manual bag holding device Bag shaker Cooling fan Overload protection SPECIAL EQUIPMENT Special grinding discs Slide cut-off 10 kg hopper Outlet extension Overload protection Standard 1203 - Art.No.262206 220-240V/50Hz/1 1.4 kW 1400 g/min 1100 g 120 mm shaking 1 left, 1 right 3 spike 38 kg 260 x 340 x 640 black • – •••• – •• – – 1203 - Art.No.262207 220V / 60Hz 1.4 kW 1400 g/min 1100 g 120 mm shaking 1 left, 1 right 13 spike 38 kg 260 x 340 x 640 black • – •••• – •• – – 1203 - Art.No. 262209 230 V / 50Hz Engl. UK-St 1.4 kW 1400 g/min 1100 g 120 mm shaking 1 left, 1 right 13 spike 38 kg 260 x 340 x 640 black • – •••• – •• – – The KR 1203 model is the ideal solution everywhere that fast, reliable and uniform grinding is required. Coffee stores with a large volume of business, supermarkets and roasting establishments value these coffee grinders highly for their exceptional performance, sturdiness and simple and safe operation. • Specially developed motors allowing large grinding capacity at all degrees of fineness • Preservation of coffee’s unique aromatic oils thanks to uniform, gentle and cool grinding made possible by specially sharpened discs developed by Ditting • Continuously variable adjustment of grinding fineness. • Minimal coffee particles left in discharge tube thanks to built-in vibrating device or manual tapper • Efficient bag shaking device distributes grounds evenly into bag and ensures all particles are dispensed • Precision grinding discs made of high quality material that is extremely wear resistant. The original discs can be re-sharpened up to 2-3 times with proper care and maintenance • Easy to maintain and clean StarbuckS SpecificationS: retail grinder KR 1203 10808 THE QUIET ONE Best-In-Class Quiet Blending Technology The ultimate blender with unparalleled sound reduction, exceptional beverage blends, and improved speed of service. Smart Product Design •Twist Lock sound enclosure is easier to remove and clean •The Advance container creates faster, smoother pours resulting in time and cost savings along with improved customer experience •Larger centering pad allows for simple, one-step cleaning •Advanced vibration dampening technology results in a more enjoyable atmosphere •4 program buttons with 34 optimized settings for easier, consistent blending •Air management and powerful ≈3-peak output HP motor reduces noise, improves reliability, and minimizes downtime vitamix.com12508 On Counter Blender Starbucks: #11074330 Vitamix: #062911 Motor: ≈3 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 15 A, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender Starbucks: #11007909 Vitamix: #040015 Motor: ≈2 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 10 A, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm North and South American Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm North and South American plug configuration applies to the following countries: Bahamas Belize Bermuda Brazil* Canary Islands Cayman Islands Colombia Costa Rica Dominican Rep. Ecuador El Salvador Guam Guatemala Honduras Mexico Puerto Rico United States *120V option for Brazil ©2017 Vita-Mix® Corporation 02/1712508 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com ©2016 Vita-Mix® Corporation 11/16 On Counter Blender (Canada Only) Starbucks: #TBD Vitamix: #TBD Motor:≈3 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 15 A, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Canada Only) Starbucks: #11010765 Vitamix: #040016 Motor: ≈2 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 10 A, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Canadian Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. 12508 On Counter Blender (Argentina Only) Starbucks: #TBD Vitamix: #TBD Motor:≈3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Argentina Only) Starbucks: #11012099 Vitamix: #051025-2657 Motor: ≈2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Argentina Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com ©2016 Vita-Mix® Corporation 11/16 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm 12508 On Counter Blender Starbucks: #TBD Vitamix: #TBD Motor:≈3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender Starbucks: #11012093 Vitamix: #051025-2385 Motor: ≈2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Schuko Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm Schuko plug configuration applies to the following countries: Albania Austria Belgium Bolivia Bulgaria Chile Czech Republic Finland France Germany Greece Greenland Hungary Iceland India Indonesia Jordan Luxembourg Majorca Netherlands Norway Paraguay Peru Poland Portugal Romania Russia Spain Sweden Tahiti Thailand Turkey Uruguay Vietnam Yugoslavia ©2016 Vita-Mix® Corporation 11/1612508 Multi-Use Rinse and Wash Station The Spraypark is the more efficient way to rinse *blending pitchers, tea shakers, and steaming pitchers. Just place the pitcher upside down, engage the automatic start, and watch as the water pressure rinses residue away, saving time and money. Smart Product Design •Automatic start and shut off for hands-free rinsing •Pre-program rinse cycle provides efficiency •In sink mounted design eliminates need for above-counter hose and faucet connection •Multi-purpose rinsing for pitchers, shakers, steaming pitchers, and milk pitchers *64 oz. containers or smaller for most manufacturers VITAMIX® SPRAYPARK vitamix.com 17564 VM0183 ©2017 Vita-Mix® Corporation 3/17 2 of 3 Product Specifications Vitamix® Spraypark Item Number: 61304 Starbucks SKU: 011075242 Electrical: 120V, 220-240V, 100V, 50/60 Hz Pack: Includes 1 rinse tower with shut off valve, power supply, Plumbing In Box, and instructions. Plumbing In Box includes the following: Pressure reducing valve, solenoid, strainer, dual check valve, backflow preventer, hose assembly/connectors, external shut off, and electronics. Net Weight: 15 lbs. FOR COMMERCIAL USE ONLY Replacement Parts Item Number: 063252 Starbucks SKU: 011075244 Pack: Includes 1 Spray Cage Item Number: 063251 Starbucks SKU: 011075245 Pack: Includes 1 Shuttle Assembly Item Number: 063247 Starbucks SKU: 011075246 Pack: Includes 1 Nozzle Item Number: 063246 Starbucks SKU: 011075247 Pack: Includes 1 Tower Assembly 12.399 17.330 8.631#2 Use this image to replace image on redlined copy labeled #2 5.747 13.247 .470 .356 6.650 .500 17564 VM0183 COR stores needs to submit a work task for replacements and repairs. LS stores needs to reach out to ICEE - dispatchsupervisor@icee.com or call 1-800-423-3872 and ask for dispatch supervisor. ©2017 Vita-Mix® Corporation 3/17 3 of 3 Plumbing Layout *Power supply cord length 6 feet, 4 feet usable ITEM DESCRIPTION QTY 1 SS BRAIDED HOSE / 3/8” COMP - 3/8” COMP / 12” LNG 3 2 ADAPTER / 3/8” COMP - 1/2” M NPT / BRASS 2 3 SHUT OFF VALVE 1 4 NIPPLE / HEX / BRASS / 1/2” M NPT / WITH THREAD SEALER 1 5 STRAINER / WYE / 100 MESH / CLEANOUT 1 6 ELBOW / 3/8” COMPRESSION - F GHT / BRASS 3 7 ADAPTER / 1/2” M NPT - M GHT / BRASS 3 8 PRESSURE REDUCING VALVE / 1/2” F NPT 1 9 STEM ADAPTOR / PUSH FIT / 1/2” STEM - 1/2” M NPT 1 10 TEE / PUSH FIT / 1/2” TUBE 2 11 TUBE / LLDPE / 1/2” OD X 3.75” OAL 2 12 STEM ELBOW / 1/2” STEM - 1/2” TUBE 2 13 SHUT OFF VALVE / PUSH FIT / 1/2” TUBE 1 14 STEM ADAPTOR / PUSH FIT / 1/2” TUBE - 3/8” M NPT 1 15 SOLENOID / 24 VDC / 3/8” F NPT 1 16 ELBOW / SWIVEL / 1/2” TUBE - 3/8” M NPT 1 17 TUBE / LLDPE / 1/2” OD X 1.9” OAL 1 18 ELBOW / PUSH FIT / 1/2” TUBE - 1/2” TUBE 1 19 TUBE / LLDPE / 1/2” OD X 2.25” OAL 1 20 TUBE / LLDPE / 1/2” OD X 4.2 OAL 1 21 ADAPTOR / STRAIGHT / PUSH FIT / 1/2” TUBE - 1/2” M NPT 1 22 DUAL CHECK VALVE / 1/2” F NPT 1 23 TOWER / AUTO RINSER 1 24 NOZZLE / ONE PIECE 1 25 SHUTTLE BODY ASY 1 26 SHUTTLE HEAD 1 27 RETAINER NUT ASSEMBLY / SPRAYPARK TOWER 1 28 LID ASY / PIB / BARE 1 29 BOTTOM ASY / PIB /BARE 1 30 NOZZLE ASY / MANUAL 1 31 POWER SUPPLY / RINSER / SPRAYPARK 1 17564 VM0183 Technical Manual CUT SHEETS © Thermoplan AG | 1/17/2019 19742 Table of contents TM_Mastrena_II_Cutsheets_EN-US 2 / 10 © Thermoplan AG Table of contents 1 M2-CS (230 V).............................................................................................................................. 3 2 M2-CS (400 V).............................................................................................................................. 4 3 M2-CS (208 V).............................................................................................................................. 5 4 M2-CS (200 V).............................................................................................................................. 6 5 Water pump CE............................................................................................................................. 7 6 Water pump US............................................................................................................................. 8 7 Water connection specifications..................................................................................................... 9 19742 TM_Mastrena_II_Cutsheets_EN-US M2-CS (230 V) © Thermoplan AG 3 / 10 1 M2-CS (230 V) <1 m / 3.2 ft / 40° 11 0 4. 3 585 [mm / in] 600 63 0 25 35 0 110 100 12 0 50 50 35 0 2 2 23 24 . 8 13 . 7 23 0 9 4 . 7 23.6 10 0 4 1 13 . 7 1 4.3 4 585 / 23 50 2 50 2 25 1 3 2 2 1 Do not cover more than 50% of the marked area. 2 Do not place objects on the marked area. 3 Hole diameter 100 mm / 4 in for the water inlet and water drain, power cable, water pump cable and Ethernet cable. Drain • Distance machine to drain < 1 m / 3.2 ft at 40°. • The drain line (pipe) must not sag. • No back pressure in the drain line. • The end of the line must not be submerged in water. Machine parameters Connection 220-240 VAC / 50/60 Hz Active power 5250 – 6250 W Dimensions (W / D / H) 585 x 600 x 630 mm 23 x 23.6 x 24.8 in Weight 95 kg / 209.43 lbs 19742 M2-CS (400 V)TM_Mastrena_II_Cutsheets_EN-US 4 / 10 © Thermoplan AG 2 M2-CS (400 V) <1 m / 3.2 ft / 40° 11 0 4. 3 585 [mm / in] 600 63 0 25 35 0 110 100 12 0 50 50 35 0 2 2 23 24 . 8 13 . 7 23 0 9 4 . 7 23.6 10 0 4 1 13 . 7 1 4.3 4 585 / 23 50 2 50 2 25 1 3 2 2 1 Do not cover more than 50% of the marked area. 2 Do not place objects on the marked area. 3 Hole diameter 100 mm / 4 in for the water inlet and water drain, power cable, water pump cable and Ethernet cable. Drain • Distance of machine to drain < 1 m / 3.2 ft at 40°. • The drain line (pipe) must not sag. • No back pressure in the drain line. • The end of the line must not be submerged in water. Machine parameters Connection 380 – 415 VAC / 50/60 Hz Active power 7600 – 8900 W Dimensions (W / D / H) 585 x 600 x 630 mm 23.03 x 23.62 x 24.8 in Weight 95 kg / 209.43 lbs 19742 TM_Mastrena_II_Cutsheets_EN-US M2-CS (208 V) © Thermoplan AG 5 / 10 3 M2-CS (208 V) <1 m / 3.2 ft / 40° 11 0 4. 3 585 [mm / in] 600 63 0 25 35 0 110 100 12 0 50 50 35 0 2 2 23 24 . 8 13 . 7 23 0 9 4 . 7 23.6 10 0 4 1 13 . 7 1 4.3 4 585 / 23 50 2 50 2 25 1 3 2 2 1 Do not cover more than 50% of the marked area. 2 Hole diameter 100 mm / 4 in for the water inlet and water drain, power cable, water pump cable and Ethernet cable. 3 Do not place objects on the marked area. Drain • Distance of machine to drain < 1 m / 3.2 ft at 40°. • The drain line (pipe) must not sag. • No back pressure in the drain line. • The end of the line must not be submerged in water. Machine parameters Connection 208 VAC / 50/60 Hz Active power 5800 W Dimensions (W / D / H) 585 x 600 x 630 mm 23.03 x 36.62 x 24.8 in Weight 95 kg / 209.43 lbs 19742 US & CANADA Standard M2-CS (200 V)TM_Mastrena_II_Cutsheets_EN-US 6 / 10 © Thermoplan AG 4 M2-CS (200 V) <1 m / 3.2 ft / 40° 11 0 4. 3 585 [mm / in] 600 63 0 25 35 0 110 100 12 0 50 50 35 0 2 2 23 24 . 8 13 . 7 23 0 9 4 . 7 23.6 10 0 4 1 13 . 7 1 4.3 4 585 / 23 50 2 50 2 25 1 3 2 2 1 Do not cover more than 50% of the marked area. 2 Hole diameter 100 mm / 4 in for the water inlet and water drain, power cable, water pump cable and Ethernet cable. 3 Do not place objects on the marked area. Drain • Distance of machine to drain < 1 m / 3.2 ft at 40°. • The drain line (pipe) must not sag. • No back pressure in the drain line. • The end of the line must not be submerged in water. Machine parameters Connection 200 VAC / 50/60 Hz Active power 5350 W Dimensions (W / D / H) 585 x 600 x 630 mm 23.03 x 36.62 x 24.8 in Weight 95 kg / 209.43 lbs 19742 TM_Mastrena_II_Cutsheets_EN-US Water pump CE © Thermoplan AG 7 / 10 5 Water pump CE 150 5.9 [mm / in] 288.5 11.3 15 8 6. 2 31.5 1.2 Machine parameters Connection 230 VAC / 50/60 Hz Active power 90 W Dimensions (W / D / H) 150 x 288.5 x 158 mm 5.9 x 11.3 x 6.2 in Weight 6.2 kg 19742 Water pump US TM_Mastrena_II_Cutsheets_EN-US 8 / 10 © Thermoplan AG 6 Water pump US 150 5.9 [mm / in] 326 12.8 15 8 6. 2 31.7 1.2 Machine parameters Connection 208 VAC / 50/60 Hz Active power 150 W Dimensions (W / D / H) 150 x 326 x 158 mm 5.9 x 12.8 x 6.2 in Weight 7 kg 19742 TM_Mastrena_II_Cutsheets_EN-US Water connection specifications © Thermoplan AG 9 / 10 7 Water connection specifications Water connection specifications Water connection 3/8“ (CE) / 9/16“ (US) Water inlet pressure 2-4 bar / 30-60 psiG Chlorine None TDS 70-200 ppm Total hardness 5-8 °dH (8-14 °fH) pH 6.8-7.4 Alkalinity < 100 ppm Iron < 0.25 ppm Water flow 2.0l/min / 0.54 gpm Water hardness conversion table Water hardness German French English Ppm Mval/l 1° dH 1.0 1.79 1.25 17.8 0.357 1° fH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.86 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/I 2.8 5.0 3.5 50.0 1.0 19742 Thermoplan AG Thermoplan-Platz 1 6353 Weggis, Switzerland Tel. +41 41 392 12 00 thermoplan@thermoplan.ch www.thermoplan.ch TM_Mastrena_II_Cutsheets_EN-US-REV-A 19742 Finished in RAL 9011 - Semi Matt Textured Finish“St a r b u c k s ” U s e r I n t e r f a c e High Speed Oven ei k o n ® e 2 s St a r b u c k s eikon® e2s Starbucks Standard features •Accelerated Cooking Technology® combines three heat technologies: -Tuned impingement -Microwave -Convection •Ventless cooking capabilities through built-in catalytic converter •Rapid cooking up to 80% faster than a conventional oven •12” cavity in a 14” width footprint •Cool to touch exterior •Very easy to clean sealed cavity with large rounded edges •Convection fan setting, 10-100% in 1% increments •Quiet operation •easyTouch®, icon driven touchscreen controls. •Easy access front mounted air filter •USB memory stick data transfer of up to 1,024 cooking profiles •In-built diagnostic testing •Stainless steel cavity and casework •Fits on a 23.6” (600 mm) worktop Starbucks model deviations •Microwave systems have had an increase to 1.00uf, capacitors on both high voltage circuits. Increased M/W power. •Single catalytic converter fitted to the upper impinger air flow path covering only half of the outlet. No lower catalyst fitted. Reduced air flow restrictions. •Lower air flow holes to heat the cook plate reduced from 3 rows to 2 rows (65 Holes). Reduced lower airflow, but increased upper airflow. •Tuned impingement system fitted with composite Mica/Teflon upper Impinger plate. Reduced upper impingement by pass. •Oven cook plate manufactured from 304 Series stainless steel in 12 Gauge. Reduced underside contact browning. •Connectivity solution to accommodate the Guardian module system, KCCM fitted internally, Mount and connection via USB and Ethernet on rear. Born Digital - Starbucks Connectivity. Specifications The eikon® e2s is the first choice for anyone who wants to prepare fresh, hot food on demand where space is at a premium. The eikon® e2s is the ideal way to cook, toast, grill, bake and regenerate a wide range of fresh or frozen foods, such as sandwiches, pastries, pizzas, fish, vegetables and meat. HOW IT WORKS The convection fan pulls air in through the back of the cavity (1). This is then heated and returned to the cavity through the catalytic converter (2) and impinger plate (3) to produce an even heat pattern in the oven. This heat pattern allows food to cook evenly and produces a crisp golden finish, every time. “St a r b u c k s ” E x t e r i o r Welbilt UK Limited, Ashbourne House, The Guildway Old Portsmouth Road, Guildford, GU3 1LR, United Kingdom Email: marketing@merrychef.com Tel: 00 44 1483 464 900 www.merrychef.com © 2023 Merrychef U.K. 1 2 3 Impinger plate Impingement plume Oven cavity Catalyst Heater element Rotating fan blade Project__Starbucks version 2 ________________ Item__E2SDBMV6DFL2SBUS __________________ Quantity _________________________________________ CSI Section 11400 20032 AMERICAS Welbilt reserves the right to make changes to the design or specifications without prior notice. ei k o n ® e 2 s St a r b u c k s INCLUDED ACCESSORIES •Flat cook plate - in 12 guage 304 series stainless steel easyTouch® CONTROL SYSTEM • Icon driven, color touch screen control panel with the capability of storing up to 1,024 multi-stage cooking profiles •Each cooking profile offers up to six (6) stages with programmable cooking times, microwave power settings and user instructions for each stage •Self diagnostics capability to monitor components •Easy menu updates or data transfer via USB memory stick MICROWAVE POWER •Microwave settings, off or 5-100% in 1% increments •Distribution system, rotating active antennae CONVECTED HEAT •Temperature settings OFF and from 212°F to 527°F (100° to 275°C) in 1°C steps • Distribution system, Tuned Impingement POWER REQUIREMENTS & OUTPUT *This is not consumption. **This is approx. microwave power output. DIMENSIONS MODEL OVERALL SIZE HIGH POWER VERSIONHEIGHT WIDTH DEPTH eikon® e2s SBUS 24.4”(620 mm)14.0”(356 mm)23.4”(595 mm)NET 134 lbs. (60.7 kg)GROSS 155 lbs. (70.4 kg) Ashbourne House, The Guildway Old Portsmouth Road, Guildford, GU3 1LR, United Kingdom Email: marketing@merrychef.com Tel: 00 44 1483 464 900 www.merrychef.com © 2023 Merrychef U.K. ei k o n e 2 s S t a r b u c k s s p e c s h e e t _ U S A _ 1 4 0 9 2 3 Guardian module, not included. Starbucks model number Model number ELECTRICAL SUPPLY POWER OUTPUT (APPROX.) Voltage Frequency Arrangement Plug Type Plug phase current rating* Max. Power Input Microwave** (IEC 705) 100% Convected Heat Combination Mode 11153261 e2SDBMV6DFL2SBUS 208- 240V 60HZ Two Pole 2P + GND NEMA 6-30P 30A 6000 W 2000 W 2200 W 2000 W** + 2200 W 11153411 e2SDBMV5DFL2SBLA 220- 230V 50HZ Single Pole L + N + E NEMA 6-30P 30A 6000 W 2000 W 2200 W 2000 W** + 2200 W 11153410 e2SDBMV6DJL2SBLA 208- 240V 60HZ Single Pole L + N + E 30A BR IEC 3 Pin 30A 6000 W 2000 W 2200 W 2000 W** + 2200 W 14.02in356.0mm 12.2in 311.0mm 24.25in 616.0mm 12.2in 311.0mm 6. 6 i n 16 8 . 5 m m 7. 7 4 i n 19 6 . 5 m m 25 . 9 6 i n 65 9 . 3 m m 7. 8 9 i n 20 0 . 5 m m 24 . 5 0 i n 62 2 . 4 m m 36.31in 922.3mm 4.85in 123.1mm 4.33in 110.0mm 4. 1 9 i n 10 6 . 5 m m 4. 1 8 i n 10 6 . 2 m m 16 . 5 9 i n 42 1 . 4 m m 1. 9 6 i n 49 . 7 m m FOOD COOKING AREA 14.02in356.0mm 12.2in 311.0mm 24.25in 616.0mm 12.2in 311.0mm 6. 6 i n 16 8 . 5 m m 7. 7 4 i n 19 6 . 5 m m 25 . 9 6 i n 65 9 . 3 m m 7. 8 9 i n 20 0 . 5 m m 24 . 5 0 i n 62 2 . 4 m m 36.31in 922.3mm 4.85in 123.1mm 4.33in 110.0mm 4. 1 9 i n 10 6 . 5 m m 4. 1 8 i n 10 6 . 2 m m 16 . 5 9 i n 42 1 . 4 m m 1. 9 6 i n 49 . 7 m m FOOD COOKING AREA 14.02in 356.0mm 12.2in 311.0mm 24.25in616.0mm 12.2in 311.0mm 6. 6 i n 16 8 . 5 m m 7. 7 4 i n 19 6 . 5 m m 25 . 9 6 i n 65 9 . 3 m m 7. 8 9 i n 20 0 . 5 m m 24 . 5 0 i n 62 2 . 4 m m 36.31in922.3mm 4.85in123.1mm 4.33in 110.0mm 4. 1 9 i n 10 6 . 5 m m 4. 1 8 i n 10 6 . 2 m m 16 . 5 9 i n 42 1 . 4 m m 1. 9 6 i n 49 . 7 m m FOOD COOKING AREA 14.02in 356.0mm 12.2in311.0mm 24.25in 616.0mm 12.2in 311.0mm 6. 6 i n 16 8 . 5 m m 7. 7 4 i n 19 6 . 5 m m 25 . 9 6 i n 65 9 . 3 m m 7. 8 9 i n 20 0 . 5 m m 24 . 5 0 i n 62 2 . 4 m m 36.31in 922.3mm 4.85in 123.1mm 4.33in110.0mm 4. 1 9 i n 10 6 . 5 m m 4. 1 8 i n 10 6 . 2 m m 16 . 5 9 i n 42 1 . 4 m m 1. 9 6 i n 49 . 7 m m FOOD COOKING AREA 14.02in 356.0mm 12.2in311.0mm 24.25in 616.0mm 12.2in311.0mm 6. 6 i n 16 8 . 5 m m 7. 7 4 i n 19 6 . 5 m m 25 . 9 6 i n 65 9 . 3 m m 7. 8 9 i n 20 0 . 5 m m 24 . 5 0 i n 62 2 . 4 m m 36.31in 922.3mm 4.85in 123.1mm 4.33in110.0mm 4. 1 9 i n 10 6 . 5 m m 4. 1 8 i n 10 6 . 2 m m 16 . 5 9 i n 42 1 . 4 m m 1. 9 6 i n 49 . 7 m m FOOD COOKING AREAFOOD COOKING AREA 20032 AMERICAS The NG3000 series nitrogen generator is designed to meet the demands of keg based nitro cold brew dispensing systems, while minimizing required floor space 01.21.2020MODEL NO. 1993010 NITROGEN GAS GENERATORTM PRODUCT INFORMATION N2 Purity Up to 99.8% Output Pressure Up to 125 psi Noise Level ≤ 60 dB(A) Environment Clean, dust free, well ventilated Normal Ambient 4-40°C / 39-104°F Safety Certificates NSF and cULus certified Weight Amp hp kW lbs kg Volts Freq. 2.8 1/4 0.19 65 29 120 60 POWER SWITCH PRESSURE GAUGE NITROGEN OUTPUT 21679 - LOW VOLTAGE The NG3000 series nitrogen generator is designed to meet the demands of keg based nitro cold brew dispensing systems, while minimizing required floor space 01.21.2020MODEL NO. 1993011 NITROGEN GAS GENERATORTM PRODUCT INFORMATION N2 Purity Up to 99.8% Output Pressure Up to 125 psi Noise Level ≤ 60 dB(A) Environment Clean, dust free, well ventilated Normal Ambient 4-40°C / 39-104°F Power Cords Plug Types F,G,I,M available Safety Certificates NSF certified, CE approval pending Weight Amp hp kW lbs kg Volts Freq. 2.8 1/4 0.19 65 29 230 50 POWER SWITCH PRESSURE GAUGE NITROGEN OUTPUT 21679 - HIGH VOLTAGE LEBAL ATAD NOITUAC LEBAL LEBAL DNUORG KCOHS CIRTCELE LEBAL GNINRAW TCENNOCSID LEBAL REWOP M&O DAER LEBAL LAUNAM ETADNOITPIRCSEDREBMUN TRAP TEEHS LIATED :SETON SNOITACIFICEPS TSET.1 A :TOP‐YH zH05 ,V891 :TSET TRATS TLOV WOL ISP 231‐811 :ERUSSERP TUO TUC ISP 211‐89 :ERUSSERP NI TUC A/N :GNITTES EVLAV FEILER ERUSSERP A/N :GNITTES EMIT NO REMIT SPMA 3.2=< :zH05/V032 TA WARD PMA SDNOCES 481=< :EGRAHC OT EMIT NO %0.29=> :LEVEL YTIRUP 2N TSET LANOITCNUF :)ACKU ,FSN ,EC( LEBAL ATAD TNIRP.2 1103991 :ON METI HLSSD‐1NM3‐R68 :CSED zH06‐05/042‐022 :TLOV A5.1/A1.2 :TNERRUC C°04/4 :PMET ISP 521 :SP )FFO .CES 051/ NO .CES 011( )ELCYC YTUD %24( HFCS 3 XAM 2 FO 1 TEEHS P :NOISIVER 1202/1/9 1103991METSYS 2N V032 HLSSD‐1NM3‐R68 The Public Health and Safety Organization NSF Product and Service Listings These NSF Official Listings are current as of Wednesday, October 13, 2021 at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions. Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/Certified/food/Listings.asp?Company=C0304853& NSF/ANSI 18 Manual Food and Beverage Dispensing Equipment Gast Mfg. Inc. 2300 Highway M-139 Benton Harbor, MI 49023 United States 269-927-5743 Facility : Benton Harbor, MI COMPONENTS: LEBAL ATAD NOITUAC LEBAL LEBAL DNUORG KCOHS CIRTCELE LEBAL GNINRAW TCENNOCSID LEBAL REWOP M&O DAER LEBAL LAUNAM ETADNOITPIRCSEDREBMUN TRAP TEEHS LIATED :SETON SNOITACIFICEPS TSET.1 A :TOP‐YH zH06 ,V301 :TSET TRATS TLOV WOL ISP 231‐811 :ERUSSERP TUO TUC ISP 211‐89 :ERUSSERP NI TUC A/N :GNITTES EVLAV FEILER ERUSSERP A/N :GNITTES EMIT NO REMIT SPMA 0.3=< :V511 TA WARD PMA KAEP SDNOCES 561=< :EGRAHC OT EMIT NO %0.29=> :LEVEL YTIRUP 2N TSET LANOITCNUF )FSN ,suLUc( :LEBAL LEDOM TNIRP.2 0103991 :METI HHBSD‐1NM3‐R68 :CSED zH06/V021 :TLOV A9.2 :TNERRUC C°04/4 :PMET ISP 521 :SP )FFO .ces 051/NO .ces 09( )ELCYC YTUD %73( HFCS 3 xaM 2 FO 1 TEEHS L :NOISIVER 1202/01/6 0103991METSYS 2N 06/021 HHBSD‐1NM3‐R68 CERTIFICATE OF COMPLIANCE Certificate Number 20190718-E186511 Report Reference E186511-20190708 Issue Date 2019-JULY-18 Bruce Mahrenholz, Director North American Certification Program UL LLC Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please contact a local UL Customer Service Representative at http://ul.com/aboutul/locations/ Page 1 of 1 Issued to: JUN-AIR USA INC 2300 M139, PO BOX 97 BENTON HARBOR MI 49022 This certificate confirms that representative samples of COMPRESSORS, VACUUM PUMPS AND PNEUMATIC PAINT SPRAYERS USL, CNL - Tank Type Compressor, Model 86R-3MN1- DXXXX Have been investigated by UL in accordance with the component requirements in the Standard(s) indicated on this Certificate. UL Recognized components are incomplete in certain constructional features or restricted in performance capabilities and are intended for installation in complete equipment submitted for investigation to UL LLC. Standard(s) for Safety: UL1450 - Motor Operated Air Compressors, Vacuum Pumps, and Painting Equipment CAN/CSA C22.2 No. 68 - Motor Operated Appliances (Household and Commercial) Additional Information: See the UL Online Certifications Directory at https://iq.ulprospector.com for additional information. This Certificate of Compliance does not provide authorization to apply the UL Recognized Component Mark. Only the UL Follow-Up Services Procedure provides authorization to apply the UL Mark. Only those products bearing the UL Recognized Component Mark should be considered as being UL Certified and covered under UL’s Follow-Up Services. Look for the UL Recognized Component Mark on the product. NSF International 789 N. Dixboro Road, Ann Arbor, MI 48105 USA RECOGNIZES Gast Mfg. Inc. Benton Harbor. MI AS COMPLYING WITH NSF/ANSI 18 AND ALL APPLICABLE REQUIREMENTS, PRODUCTS APPEARING IN THE NSF OFFICIAL LISTING ARE AUTHORIZED TO BEAR THE NSF MARK. % _' w.��h Ahad Alcre.m AmWlrc46/ih Anoime Wam�ol 9ybW.ehWel temtlM�lnatim¢ NCmA Thiaafincza i, th, ine"urNSF Inmmational mad must he mmnei upnmqucm. Tm'emfifiee¢ remains valid as lent as this tllent M1ae pmtlws In 4ismagWMe,nmwdentrants, For,he mod cmm and eumphse Using inf atimi, pleve mees, bars obtai¢(wwwrmEmn. 1Lt.—E September 15, 2016 Sarah Knot Cardficart C0304y53 - 01 Global Managing Director, Fond Safety Product Cenlfication Element 7 Nitrogen Gas Generator[1] LOA-(1)(2)(3)-(4)(5)(6)(7)(8) [1] (1) Receiver Size: 0 - No tank 0.4 - 0.4 liter tank 1.5 - 1.5 liter tank 4 - 4 liter tank 15 - 15 liter tank 25 - 25 liter tank (2) Enclosure Type: M - Metal Cover (3) Separator Type: N1 - Nitrogen Separator (CMS) N2 - Nitrogen Separator (Membrane) (4) Compressor Configuration: A - Single Cylinder, Low Stroke B - Single Cylinder, High Stroke (0.35") C - Single Cylinder, High Stroke (0.42") Bent Valve (100psi max) G - Dual Parallel Cylinder, Low Stroke H - Dual Parallel Cylinder, High Stroke (0.37") J - Dual Parallel Cylinder, High Stroke (0.42") Bent Valves N - Dual Staged Cylinders, Std Stroke P - Dual Independent Cylinders, Std Stroke S - Special compressor configuration (5) Accessory Configuration: A - Manual tank drain, 5µ F/R manual drain, no bottle, pressure switch unloader B - Manual tank drain, 5µ F/R auto drain, with bottle C - Manual tank drain, 5µ F/R manual drain, 0.01µ Coalescing Filter, no bottle D - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, with bottle E - Manual tank drain, 5µ F/R auto drain, no bottle, pressure switch unloader F - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, no bottle K - Auto tank drain, 5µ F/R auto drain, with bottle L - Auto tank drain, 5µ F/R auto drain, 0.01µ Coalescing filter, with bottle M - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, no bottle N - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, with bottle R - Integrated IOT S - OEM Specific Model (6) Elec/Region Config: A - 100/50 or 60 Japan (NEMA 1-15 or 5-15) B - 120/50 or 60 NA (NEMA 5-15) C - 220-240 50 or 60 NA (NEMA 6-15) D - 220-240 50 or 60 EU (CEE 7/7) E - 220-240 50 or 60 EU (CEE 7/7) & GB adaptor F - 220-240 50 or 60 CH (NEMA 1-15 or AS-3112) G - 220-240 50 or 60 AU (AS-3112) H - 220-240 50 or 60 GB (IEC Type G) S - Special voltage/plug (7) System Regulatory: A - CE B - CSA C - cULus D - CE/cULus E - CCC F - cCSAus G - cULus/NSF H - None S - Special (8) Tank Regulatory: A - CE B - ASME C - ASME Singapore D - GB (china) E - CRN F - ASME/CE G - ASME/CRN H - CE/UL S - Special Nitrogen Gas Generator for Beverage Systems[2] 86R-(1)(2)(3)-(4)(5)(6)(7)(8) 87R-(1)(2)(3)-(4)(5)(6)(7)(8) [2] (1) Receiver Size: 0 - No Tank 1.5 - 1.5 liter tank 3 - 3 liter tank 4 - 4 liter tank 15 - 15 liter tank (2) Enclosure Type: M - Metal Cover (3) Separator Type: N1 - Nitrogen Separator (CMS) N2 - Nitrogen Separator (Membrane) NB - Nitrogen Separator (CMS), CO2 Blender (4) Compressor Configuration: A - Single Cylinder, Low Stroke B - Single Cylinder, High Stroke (0.35") C - Single Cylinder, High Stroke (0.42") Bent Valve (100psi max) D - Single Cylinder, High Stroke (0.45") Bent Valve G - Dual Parallel Cylinder, Low Stroke H - Dual Parallel Cylinder, High Stroke (0.37") J - Dual Parallel Cylinder, High Stroke (0.42") Bent Valves N - Dual Staged Cylinders, Std Stroke P - Dual Independent Cylinders, Std Stroke S - Special compressor configuration (5) Accessory Configuration: A - Manual tank drain, 5µ F/R manual drain, no bottle, pressure switch unloader B - Manual tank drain, 5µ F/R auto drain, with bottle C - Manual tank drain, 5µ F/R manual drain, 0.01µ Coalescing Filter, no bottle D - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, with bottle E - Manual tank drain, 5µ F/R auto drain, no bottle, pressure switch unloader F - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, no bottle K - Auto tank drain, 5µ F/R auto drain, with bottle L - Auto tank drain, 5µ F/R auto drain, 0.01µ Coalescing filter, with bottle M - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, no bottle N - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, with bottle S - OEM Specific Model (6) Elec/Region Config: A - 100/50 or 60 Japan (NEMA 1-15 or 5-15?) B - 120/50 or 60 NA (NEMA 5-15) C - 220-240 50 or 60 NA (NEMA 6-15) D - 220-240 50 or 60 EU (CEE 7/7) E - 220-240 50 or 60 EU (CEE 7/7) & GB adaptor F - 220-240 50 or 60 CH (NEMA 1-15 or AS-3112) G - 220-240 50 or 60 AU (AS-3112) H - 220-240 50 or 60 GB (IEC Type G) S - Special voltage/plug (7) System Regulatory: A - CE B - CSA C - cULus D - CE/cULus E - CCC F - cCSAus H - cULus / NSF N - None S - Special (8) Tank Regulatory: A - CE B - ASME C - ASME Singapore D - GB (china) E - CRN F - ASME/CE G - ASME/CRN H - CE/UL S - Special Number of matching Manufacturers is 1 Number of matching Products is 3 Processing time was 0 seconds Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Starbucks Single Cup Brewer (CM9700)– Rapid Brewer for freshest coffee Specification Production# Water Access Finish Hoppers Hopper Capacity Display 90300011503 Plumbed Black/Matt 6 2 lbs (0.9kgs) Full color touch Electrical & Capacity Power Max Current Watts Plug type Phase dedicated 208 VAC 60 Hz Draw 40 A at 208 VAC Usage 8.32 kW at 208 VAC NEMA 14-50 (not supplied ) single Water & Plumbing requirements Pressure kPa Fitting Supplied pH Hardness Input H²O Temp. ≥ 30 PSI at 1 gpm 250-350 3/8" Male NPT 6.5-8.5 90-140 ppm 60°F (15.5°C) Chlorine TDS Alkalinity Iron ≤0.5 ppm 50-200ppm 20-140ppm ＜0.3ppm Dragon Will Enterprise Ltd. Dongling Intelligent Electrical Appliances Technology Co., Height: 32” Width:22.5” Depth:25.4” (81.3 cm) (57.1 cm) (64.5 cm) Revolutionary rapid brewing system, fast brew coffee in 30s 2 towers & 6 bean hoppers design for variety of coffee options and peak hour workloads. High performance hot water dispenser, 5 mins preheat & 5L hot water output continuously. Automated brewing, grinding and managing spent grounds frees up your partner to spend time with your customers Recipe download, upload & firmware update by IOT Quick access ground bins design 22885 BREWER 23381 POWER CORD Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. *Recommended countertop hole to be 4” (100mm) for power cord and water line. Use existing dedicated filtered water supply satisfying all Starbucks water requirements Use existing dedicated 208 VAC, single-phase, 60 Hz, 50 Amp service dedicated line Unit does not connect to an external waste drain line. *Clover Vertica comes with 6 extra bean hoppers & 12 label holders. UNIT SHIPPING Height Width Depth Weight Height Width Depth Weight English 32” 22.5” 25.4” 330.7 lbs 45” 44.9” 33.5” 429.9 lbs Metric 81.3 cm 57.1 cm 64.5 cm 150 Kg 114.2 cm 114 cm 85 cm 195 Kg 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction 12/14/23 Two separate boxes are ordered with each Clover Vertica, one has the cord set and the other has the install kit you should have 3 boxes to complete the install. 1.Remove the clover Vertica from the pallet and boxes, each tower is individually packed and there are three boxes that hold extra parts and hoppers. Contents below: •12-hoppers •12-label holders •2-coffee tower bottom cover (sheet metal) •14-thumb screws •20-coffee backsplash •1 -water backsplash 2.Place the water tower on its side on and install the cord set. •Remove the lower back panel •Thread the cord with the elbow strain relief into the back of the machine and connect the two hots and ground to the appropriate terminals then tighten the nut on the strain relief. Reattach the back panel. •Install the cord CamCo NEMA 14-50P cord cap from the install kit box 3.Place the two coffee towers on the counter with the “cut out” panel facing the water tower 4.Unpack 6 hoppers and put them on the machine 5.leave boxes unopened next to the machine. See example of hoppers on the machine below. No need to connect towers the commissioning supplier will do that. 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction 12/14/23 Water Boost Kit 1.The Pentair water boost kit comes with all the valves and supply hoses needed for connection. 2.Remove cover and mount water boost and CV valve to the side of the cabinet under the Vertica, be careful not to penetrate screws into the opposite cabinet. 3.Connect supply hoses using the supplied install guide, penetrate holes in the cabinet as needed to run the hoses from the supply valve to the water boost and up to the Vertica. Do not turn on supply water or plug pump in. This will be done by the certified commissioning supplier. 22885 BREWER 23381 POWER CORD POU WATERBOOST, 30/35 PSI, 115V SYSTEM SPECIFICATION SHEET FOODSERVICE.PENTAIR.COM SYSTEM DESCRIPTION The Pentair® Shurflo® POU 115V Waterboost system maintains a constant water pressure of 35-45 psi to deliver quality beverages for a variety of foodservice water treatment applications. Ideal for applications that have low, fluctuating, or no water pressure. FEATURES ∙ BENEFITS ◆Integrated system bypass with 0.5 gallon buffer tank extends pump life. ◆50 mesh inline filter at entry of system ◆NSF 18 certified booster system (need to check with regulatory for any statements) ◆cUL approved assembly (need to check with regulatory for correct statement) ◆Installation kit includes 4 metal braided hoses, compression fittings, inline shut off valve, 30/35 psi pressure regulator, camco power grip 50 amp male plug, and bottle of cafiza x90 cleaning tablet.* * Installation kit is not included in NSF or cUL certifications. APPLICATIONS ◆Fountain ◆Ice ◆Coffee ◆Tea INSTALLATION TIPS ◆Choose a mounting location suitable to support the weight of the booster while operating. ◆Install vertically and allow four (4) to six (6) inches above the unit for adjustment. ◆Flush by running water through the booster for five (5) minutes. ◆Do not install where the booster could be exposed to freezing temperatures. ◆For more details, see the installation, operation, and maintenance guide. System Part Number: EV9910-00 POU WATERBOOST, 30/35 PSI, 115V SYSTEM EPA Est. 002623-IL-002 23380 United States | 1040 Muirfield Drive | Hanover Park, IL 60133 | 800.942.1153 (US Only) 630.307.3000 Main | cseverpure@pentair.com | foodservice.pentair.com Australia | 1-21 Monash Drive | Dandenong South, Vic 3175 | Australia | 011.1300 576 190 Tel | au.everpure@pentair.com China | 21F Cloud 9 Plaza, NO 1118 | Shanghai, 200052 | China | 86.21.3211.4588 Tel | china.water@pentair.com India | Boulevard, B-9/A, 7th Floor - Tower B Sector 62 | Noida - 201301 | 91.120.419.9444 Tel | indiacustomer@pentair.com Europe | Pentair Water Belgium BV | Industriepark Wolfstee, Toekomstlaan 30, B-2200 Herentals | Belgium | +32.(0).14.283.504 Tel | sales@everpure-europe.com Japan | Japan Inc. | Hashimoto MN Bldg. 7F, | 3-25-1 Hashimoto, Midori-ku, Sagamihara-shi | Kanagawa 252-0143 | Japan | 81.(0)42.775.3011 Tel | info@everpure.co.jp Southeast Asia | 390 Havelock Road, | #04-01 King’s Centre | Singapore 169662 | 65.6768.5800 Tel | cseverpure@pentair.com All indicated Pentair trademarks and logos are property of Pentair. Third party registered and unregistered trademarks and logos are the property of their respective owners. Items Included EV316026 - POU 115V Waterboost System Assembly EV316027 - PSI 30/35 POU Waterboost Kit POU WATERBOOST, 30/35 PSI, 115V SYSTEM EV9910-00 ©2022 Pentair. All rights reserved. EV9910-00 DE22 System Overall Dimensions 14.8" H x 13.4" W x 5.9" D (37.6 x 34.0 x 15 cm) Connections Inlet Connection: 1/2" MIP Outlet Connection: 1/2" MIP Incoming Pressure 5–100 PSI Water Temperature 35–100°F (2 – 38°C) Operating Weight TBD lbs (x.x kgs) Shipping Weight TBD lbs (x.x kgs) Electrical Connection 115 VAC 60HZ 0/9 AMPS MAX SPECIFICATIONS 14.8 13.5 1/2-14 NPSOUTLET1/2-14 NPSINLET 13.4 115 VAC POWER CORD5 FEET FROM THIS POINT, NOT SHOWN 6.0 For Pentair Product Warranties visit: http://pentair.com/assets/foodservice-warranty Since the conditions under which our products may be used are beyond our control, we cannot accept any liability with respect to the improper installation, application and/or use of our products. Water TreatmentAppliance - E359339 23380 ROUGH SYSTEM LAYOUT From Customer – 7/13/22 SYSTEM LAYOUT Pentair Engineering, 11/03/22-V7 POU Water Boost Rough System Layout Power 120 VAC 115 VAC 60 HZ 0.9 AMPS cUL Certified NSF 18 Certified ½ NPSM½ NPSM ½ NPSM½ NPSM 3/8" NPT INLET BREWER Equipment INLET 3/8 Comp EV310591 Reducer Bushing ¾ MPT x 3/8 FPT 3/8 COMP EV316043 Shutoff valve 3/8 Comp x 3/8 FIP EV316041 Adapter 3/8 Comp x 3/8 MIP 3/8 COMP EV316038 MB HOSE 20" 3/8Comp x 2 EV316042 Adapter 3/8 FNPT x 3/8 Comp 3/8 COMP 3/8 COMP EV316037 MB HOSE 60" 3/8Comp x 2 EV316042 Adapter 3/8 FNPT x 3/8 Comp EV316040 CF VALVE, 2X-3 WF 35PSI EV316041 Adapter 3/8 Comp x 3/8 MIP EV316026 POU 115V WATERBOOST SYSTEM ASY 3/8 COMP ½ FIP EV316035 MB HOSE 60" 3/8Comp x ½ FIP 3/8 COMP ½ FIP EV316035 MB HOSE 60" 3/8Comp x ½ FIP ½ FIP 3/8 COMP EV316036 MB HOSE 20" 3/8Comp x ½ FIP ½ FIP 3/8 COMP EV316036 MB HOSE 20" 3/8Comp x ½ FIP 60"20" 20"60" NOTE: Kit EV316027: Parts will be bagged together in box. Fitting assembly will be done on site: EV9910-00 30/35 PSI POU 115V WATERBOOST EV991000 Includes: EV316026 – POU 115V WATERBOOST SYSTEM ASY EV316027 – PSI 30/35 POU WATERBOOST KIT -KIT ITEMS are in GREEN Additional Kit items: EV316039 CAMCO PWR GRIP CORD CAP23380 Clover Vertica Pre commissioning GC Install Instruction 12/14/23 Two separate boxes are ordered with each Clover Vertica, one has the cord set and the other has the install kit you should have 3 boxes to complete the install. 1.Remove the clover Vertica from the pallet and boxes, each tower is individually packed and there are three boxes that hold extra parts and hoppers. Contents below: •12-hoppers •12-label holders •2-coffee tower bottom cover (sheet metal) •14-thumb screws •20-coffee backsplash •1 -water backsplash 2.Place the water tower on its side on and install the cord set. •Remove the lower back panel •Thread the cord with the elbow strain relief into the back of the machine and connect the two hots and ground to the appropriate terminals then tighten the nut on the strain relief. Reattach the back panel. •Install the cord CamCo NEMA 14-50P cord cap from the install kit box 3.Place the two coffee towers on the counter with the “cut out” panel facing the water tower 4.Unpack 6 hoppers and put them on the machine 5.leave boxes unopened next to the machine. See example of hoppers on the machine below. No need to connect towers the commissioning supplier will do that. 23380 Clover Vertica Pre commissioning GC Install Instruction 12/14/23 Water Boost Kit 1.The Pentair water boost kit comes with all the valves and supply hoses needed for connection. 2.Remove cover and mount water boost and CV valve to the side of the cabinet under the Vertica, be careful not to penetrate screws into the opposite cabinet. 3.Connect supply hoses using the supplied install guide, penetrate holes in the cabinet as needed to run the hoses from the supply valve to the water boost and up to the Vertica. Do not turn on supply water or plug pump in. This will be done by the certified commissioning supplier. 23380 Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Starbucks Single Cup Brewer (CM9700)– Rapid Brewer for freshest coffee Specification Production# Water Access Finish Hoppers Hopper Capacity Display 90300011503 Plumbed Black/Matt 6 2 lbs (0.9kgs) Full color touch Electrical & Capacity Power Max Current Watts Plug type Phase dedicated 208 VAC 60 Hz Draw 40 A at 208 VAC Usage 8.32 kW at 208 VAC NEMA 14-50 (not supplied ) single Water & Plumbing requirements Pressure kPa Fitting Supplied pH Hardness Input H²O Temp. ≥ 30 PSI at 1 gpm 250-350 3/8" Male NPT 6.5-8.5 90-140 ppm 60°F (15.5°C) Chlorine TDS Alkalinity Iron ≤0.5 ppm 50-200ppm 20-140ppm ＜0.3ppm Dragon Will Enterprise Ltd. Dongling Intelligent Electrical Appliances Technology Co., Height: 32” Width:22.5” Depth:25.4” (81.3 cm) (57.1 cm) (64.5 cm) Revolutionary rapid brewing system, fast brew coffee in 30s 2 towers & 6 bean hoppers design for variety of coffee options and peak hour workloads. High performance hot water dispenser, 5 mins preheat & 5L hot water output continuously. Automated brewing, grinding and managing spent grounds frees up your partner to spend time with your customers Recipe download, upload & firmware update by IOT Quick access ground bins design 22885 BREWER 23381 POWER CORD Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. *Recommended countertop hole to be 4” (100mm) for power cord and water line. Use existing dedicated filtered water supply satisfying all Starbucks water requirements Use existing dedicated 208 VAC, single-phase, 60 Hz, 50 Amp service dedicated line Unit does not connect to an external waste drain line. *Clover Vertica comes with 6 extra bean hoppers & 12 label holders. UNIT SHIPPING Height Width Depth Weight Height Width Depth Weight English 32” 22.5” 25.4” 330.7 lbs 45” 44.9” 33.5” 429.9 lbs Metric 81.3 cm 57.1 cm 64.5 cm 150 Kg 114.2 cm 114 cm 85 cm 195 Kg 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction 12/14/23 Two separate boxes are ordered with each Clover Vertica, one has the cord set and the other has the install kit you should have 3 boxes to complete the install. 1.Remove the clover Vertica from the pallet and boxes, each tower is individually packed and there are three boxes that hold extra parts and hoppers. Contents below: •12-hoppers •12-label holders •2-coffee tower bottom cover (sheet metal) •14-thumb screws •20-coffee backsplash •1 -water backsplash 2.Place the water tower on its side on and install the cord set. •Remove the lower back panel •Thread the cord with the elbow strain relief into the back of the machine and connect the two hots and ground to the appropriate terminals then tighten the nut on the strain relief. Reattach the back panel. •Install the cord CamCo NEMA 14-50P cord cap from the install kit box 3.Place the two coffee towers on the counter with the “cut out” panel facing the water tower 4.Unpack 6 hoppers and put them on the machine 5.leave boxes unopened next to the machine. See example of hoppers on the machine below. No need to connect towers the commissioning supplier will do that. 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction 12/14/23 Water Boost Kit 1.The Pentair water boost kit comes with all the valves and supply hoses needed for connection. 2.Remove cover and mount water boost and CV valve to the side of the cabinet under the Vertica, be careful not to penetrate screws into the opposite cabinet. 3.Connect supply hoses using the supplied install guide, penetrate holes in the cabinet as needed to run the hoses from the supply valve to the water boost and up to the Vertica. Do not turn on supply water or plug pump in. This will be done by the certified commissioning supplier. 22885 BREWER 23381 POWER CORD QonLiM Guangdong Xinbao Electrical Appliances Holdings Co.,Ltd Dragonwill Refrigerated Dispenser ♦ The equipment work within specification in an ambient temperature range between 60°F of 90°F and relative humidity range 0% to 90%. ♦ Milk refrigerator containing actively loaded milks, alt milk containers (Tetrapaks), and other refrigerated beverage components. Dispense product will be prechilled. ♦ User interface that is removable. ♦ Drip tray/waste capture that has option to be plumbed. ♦ Mounting bracket system for mounting on a wall ♦ The equipment refrigerate and store milk, alt milks, and other chilled ingredients at a safe holding temperature (33°F — 41°F). Existing container formats of milk can make minimal effort to attach to the dispense system. ♦ Equipment can automatically dispense liquid at recipe volumes into a Starbucks steaming pitcher (to be treated as the default dispense vessel) or into Starbucks cold cups by pressing button on panel c I& us U57E0 0 E311353 Specification • Two TFT screens show the Cavity temperature and milk mode. • Dispense prespecified Volume by press T/G/V or Tr button. • Dispense custom volume by press and hold "Free Flow" button until desired volume is dispensed then release the button. • Change Drink mode by choose the mode button(Shaken, Coffee Blended or Creme Blended) and show in the TFT screen. 4.6.5.1 Shaken: o Tall— 90g=15g o Cxra do — 120 g f 15 g ❑ Venti— 180gt15g a Trmra 240 g f 15 g 4.6.5.2 Coffee Blended o Tall— 85g-15g v gu#— 110gf15g o Vend— 168gt156 0 4.6.53 Creme BIended o Tall— 112g�15g ❑ QUO—k— 150g=15g o Y_ — 224g2615g • Change Fluid Type: Step 1: Press Shaken, Coffee Blended or Creme Blended button separately to change the mode. Step 2: While holding the Shaken button, press the free flow button to change the Fluid type (Dairy, Alt -dairy, Coconut Milk etc.). • Removable adapter system and BOM List. Items Description Material Usage 1 Rubber Silicone 1 PCS 2 Jar Bracket POM FG20-03 1 PCs 3 O Ring Silicone 1 PCS 4 Adapter POM FG20-03 1 PCS 5 Plunger rubber Silicone 1 PCS 6 Shaft Copper 1 PCS • Drip Tray and BOM List. 1 Hall Sensor N/A 1 PCS 2 Sensor cover plate ABS 750SW 1 PCS 3 Magnet ABS 750SW 1 PCS 4 Bottom plate ABS 750SW 1 PCS 5 Support plate ABS 750SW 1 PCS 6 Spring 302 Stainless Steel 2 PCS 7 Drip tray ABS 750SW 1 PCS 8 Guide plate ABS 750SW 1 PCS • Mounting bracket system and BOM List. Items Description Material Usage 1 Right Support SPEC Steel 1 PCS 2 Left Support SPEC Steel 1 PCS 3 Joint Plate SPEC Steel 1 PCS 4 Left Guide SPEC Steel 1 PCS 5 Right Guide SPEC Steel 1 PCS 6 Fix bracket SPEC Steel 2 PCS Electrical & Capacity Power Rated Current Rated Watts Plug type Phase 120 VAC 60 Hz 1.7 A 204W UL Plug Single Unit size & Package size Items Description Qty 1 Refrigerated Dispenser Unit 1 PCS 2 Drip tray 1 PCS 3 Adapter 2 PCS 4 Mounting bracket 1 PCS 5 Power cord 1 PCS / Unit Package size / Height Width Depth Weight Height Width Depth Weight English 20.2" 10.4" 14.3" 17.6lbs 24.2" 18" 21.9" 37.5lbs Metric 512mm 265mm 364mm 8kg 617mm 458mm 558mm 17k Cleaning Instruction — Dish —washer clean requirement: The Adapter system (Rubber/Bracket/Adapter/Plunger) must cleaning with dishwasher at least two times every morning and every evening to keep the Adapter system sanitation before use and overnight. Remove Guide tube from unit and use dish —washer clean every morning and evening, then return to in position — Scrub and clean maintain requirement: The unit cavity must clean at least two times every morning and evening to keep the sanitation before use and overnight. 1. Turn off the unit power. 2. Open the door and scrub the cavity Upper/Down/Left/Right surface inclusive of the inside of door surface. 3. Remove the water tank of door and poor off all water than return to in position CONVOTHERM Combi oven Project Item Quantity FCSI section Approval Date Model • easyTouch • Electric • Capacity 10 shelves • Injection Convotherm mini easyTouch y 13" x 18" , Right -hinged door Key features • 4 operating modes: Steam, combi steam, convection, rethermalization 1�-- -----� C Extra functions: f o Crisp&Tasty- 3 moisture -removal settings o BakePro -Traditional baking function with 3 settings (plus steam and rest phases) If.• o Reduced fan speed and auto reverse mode 1 j i�.`.'j �-'� /! ! easyTouch 7" full -touch screen ConvoClean system, fully automatic cleaning system with express !I° mode and Safe Cool Down function before cleaning a r � - Ethernet port (LAN) 'r USB port integrated in the control panel • Steam generated by injecting water into the oven cavity (without steam boiler) • Right -hinged door • UL listed ventless (KNLZ) no hood required, local codes prevail Standard features Options • Operating modes: Matte -black -on -stainless -steel exterior o Steam (86-248°F) with guaranteed steam saturation Unit door with left-hand hinge 0 Combi-steam (212-482'F) with automatic moisture adjustment Various voltages (single-phase on request) 0 Hot air (86-482'F) with optimized heat transfer Ethernet connection RJ45 0 Rethermalization function • easyTouch user interface: 0 7" full touchscreen Accessories 0 Press&Go - automatic cooking and baking with quick access Spray head with continuously adjustable flow regulation buttons 0 easyStart - automatic cooking and baking with product Halton condensation hood suggestions and smart recommendations Equipment stands in various sizes and designs 0 TrayTimer - load management for different products Care products simultaneously Pans 0 ecoCooking - energy saving function Trays 0 LT cooking (low -temperature cooking) / Delta-T cooking Racks 0 Cook&Hold - Cooking and keeping food warm in a single Baskets process Grilling accessories 0 Programmable with an unlimited number of cooking profiles including up to 99 steps each and a picture 0 On -screen help 0 Preset start time • Multi -point core temperature probe • Robust rotary door lever with safety lock and sure -shut function • Preheat and cool down function • Flexible shelf spacing • Steam reducer commercial combination oven with • Safe Cooldown (can be enabled through the service interface) integral systems for limiting the c UL us 0 emissions ofgrease laden air. • Full automatic ConvoClean cleaning system Y g Y Tperati n re conformsmend ti theseforthntless us��ED E operation recommendations set Porch by NFPA96 using EPA202 test method. Welbilt Inc. Phone 1-800-338-2204 www.convotherm.com 18301 St. Clair Avenue WELBILT Cleveland, OH 44110 USA 1 CONVOTHERM' Dimensions CD O N K Front view "CM CC c a cn ro co v 16.9 1.7 20.3 View from above with wall clearances Dimensions and weights Dimensions including packaging Width x height x depth 22.8 x 46.3 x 35.8 " Weight Empty weight without packaging 153 Ibs Packaging weight 29 Ibs Safety clearances* Rear 2.0 " Right-hand side 2.0 " Left-hand side (larger gap recommended for 2.0 " servicing) Top** 20.0 " * Minimum clearance to heat sources, 20". **Depends on the type of exhaust system and the ceiling's characteristics. Weights Views Side view Connection points, unit floor A Water connection (soft water (filtered), for water injection) B Water connection (cold water (unfiltered), for cleaning) C Drain connection 1.5" D Electrical connection E Electrical Ground F Rinse -aid connection G Cleaning -agent connection H Air vent 0 1.18" 1 Dry air intake 0 1.69" M Safety overflow 2.36" x 0.79" N Ethernet connection RJ45 Installation requirements Max. absolute appliance inclination during max. 2° (3.5%) operation CONVOTHERM Loading capacity Max. number of food containers [Unit has 5 sliding rails; rail spacing 2.68" max.] 13" x 18" half size sheet pans 10 12" x 20" by 2 1/2" steam table pans 5 12" x 20" wire fry baskets 6 Plates, max 0 11" 12 Max, loading weight Per combi oven 66 Ibs Per shelf level 11 Ibs Electrical supply 3- 208V-240V 60Hz (3/PE) (for 208V) Rated power consumption 8.50 kW Hot air power 8.16 kW Motor output 0.25 kW Rated current 23.6 A Supplied with a 4 conductor 6 foot long cord AWG 8 Conductor insulation rating SOOW Plug (customer supplied) 15-50P or L15-50P 3- 208V-240V 60Hz (3/PE) (for 240V) Rated power consumption 11.25 kW Hot air power 11.12 kW Motor output 0.25 kW Rated current 27.1 A Supplied with a 4 conductor 6 foot long cord AWG 8 Conductor insulation rating SOOW Plug (customer supplied) 15-50P or L15-50P Capacity Electrical specifications Water Water connection Water supply Shut-off device The unit may need to be installed with an appropriate backflow preventer in order to comply with all applicable federal, state, and local laws and regulations. Water supply Two 3/4" inner diameter GHT-M (garden hose adapter). The unit is designed for a permanent hookup to the water supply that uses a connecting hose with a minimum diameter of 1 /2" Flow pressure, 29 - 87 psi (2 - 6 bar) without ConvoClean system Flow pressure, 43.5 - 87 psi (3 - 6 bar) with ConvoClean system Appliance drain Version Naturally ventilated pipe to open pan or drain/channel, min. 1" ventilation clearance Type Depending on the length of the line and the elements used in the line, the minimum inner diameter of the line is 1.5". Water quality Water connection A* for water injection General Drinking water, typically soft water requirements (install a water treatment system if necessary) TDS 70-125ppm Hardness 70 - 125 ppm (4-7 gpg) Water connection B* for cleaning General Drinking water, typically untreated requirements water TDS 70 - 360 ppm Hardness 70 - 360 ppm (4-21 gpg) Water connections A, B* pH value 6.5 - 8.5 Cl- (chloride) max. 60 ppm Cl2 (free chlorine) max. 0.2 ppm S042-(sulfate) max. 150ppm Fe (iron) max. 0.1 ppm Si02 (silica) max. 13 ppm NH2CI (monochloramine) max. 0.2 ppm Temperature max. 104 °F / max. 40 °C * Please refer to connection points graphic, p. 2. NOTICE: The owner/operator/purchaser must ensure that the water quality requirements are met. Otherwise the unit warranty is void. CONVOTHERM° Water l V O O Water consumption Emissions Accessories ACCESSORIES Water connection A* (For more detailed information, please refer to the Accessories brochure.) 0 water consumption during cooking 0 - 4.0 gph Max. water throughput 0.13 gpm Water connections A, B with ConvoClean system 0 water consumption during cooking** 0 - 5.3 gph Max. water throughput 2.6 gpm * values intended as guide for specifying the water treatment system. ** Incl. water required for cooling the wastewater. NOTICE: See connection positions diagram, p. 2. Emissions Dissipated heat* Latent 1740 BTU/h Sensible 1911 BTU/h Drain temperature max. 140°F / 60°C Decibel rating max. 60 dBA Please note: • This document is to serve planning purposes only. • Please refer to the Installation manual for further technical data and for instructions on installation and setup. M Welbilt Inc. Phone 1-800-338-2204 www.convotherm.com 18301 St. Clair Avenue Cleveland, OH 44110 USA WELBILT' DATE: PROJECT: ITEM NO: Product Specifications - Starbucks Corporation Lengths include end panels 54-1/4"L x 35"D x 52"H□SBZ5452DR 66-1/4"L x 35"D x 52"H□SBZ6652DR Combination Non-Refrigerated Service Above Refrigerated Self-Service Case STANDARD FEATURES ■Breeze™ w/EnergyWise s/c refrigeration (Hot gas condensate) ■4''H front glass shield ■Digital controller ■Foam-in-place insulated tub ■Glass upper display area. ■Integrated average product temperature of 40°F or less ■LED top light in lower display ■Rear electrical access Features Standard Options EXTERIOR COLOR □Black Gray INTERIOR COLOR □Black Gray END PANEL LEFT □Full end panel w/mirror interior in lower display END PANEL RIGHT □Full end panel w/mirror interior in lower display FRONT GLASS □Tempered (service) REAR WRAPPING BOARD □Rear wrapping board, black Sanalite® TOE KICK □Black Gray UPPER REAR □Acrylic rear sliding doors w/o lock ELECTRICAL CONNECT □Leads REFRIGERATION □Breeze™ w/EnergyWise s/c refrigeration (Hot gas condensate) THERMOMETER □Spirit filled thermometer 3/30/2017Revised 20480348 Note: Information is subject to change at any time. Visit www.structuralconcepts.com for the most current specs. 888 E. Porter Rd. Muskegon, MI 49441 Ph. 231-798-8888 Fx. 231-798-4960 www.structuralconcepts.com DID 16238 - MODEL SBZ6652DR DID 16239 - MODEL SBZ5452DR Product Specifications Intended Environment:Type I - Designed to operate in ambient conditions of 75°F with 55% relative humidity unless noted otherwise in system information below. Warmest Avg Prod Temp ° F Intended Product To Be Displayed Zone 1 Packaged refrigerated products 40 40 Unpackaged refrigerated products2 Model Technical Specifications Model L1"L2"WattsFreqPhsSystem Circuit Volts Wires BTUHNEMA Plug Est Wt Amps ***SSTL" 99054.25N/ASBZ5452DR .00 Self-Contained Circuit #1 N/AN/ALeads Single2+G6.81601208-240 997 1,15066.25N/ASBZ6652DR .00 Self-Contained Circuit #1 N/AN/ALeads Single2+G6.83601208-240 1,010 Regulatory Approvals: All Models Accordance with AHRI Std 1200 ETL Listed to UL 471 ETL Listed to CAN/CSA 22.2 No. 120 NSF Std 7 Listed *** Does not include electric defrost on freezer models.Important Notes: 1) Units are supplied with levelers. They must be adjusted during installation to ensure the unit is level and plumb. Dimensions reflect levelers extended 1 5/8''. 2) Refer to serial label for refrigerant type. Cases built before March 2017 contain R-404a, and case built after contain R-134a. 888 E. Porter Rd. Muskegon, MI 49441 Ph. 231-798-8888 Fx. 231-798-4960 www.structuralconcepts.com 3/30/2017Revised Note: Information is subject to change at any time. Visit www.structuralconcepts.com for the most current specs. 20480348 DID 16238 - MODEL SBZ6652DR DID 16239 - MODEL SBZ5452DR Technical Information - Oasis - Combination Non-Refrigerated Service Above Refrigerated Self -Service Case Page 1 of 2 DIMENSIONS / SHIPPING Model L" L1" L2" Est Wt (lbs) N/A 54.250 0.000 990SBZ5452DR N/A 66.250 0.000 1,150SBZ6652DR ELECTRICAL Model System Circuit Volts Ph Frq Rated Load Amps Watts Wires NEMA Plug Amps Lights Amps Fans Amps Anti- Sweats Amps Misc/Refrig/ Heat Min Cir Amps Max OCP Amps SBZ5452DR Circuit #1 208-240 997 2+G Leads Single1606.81Self-Contained 15 15 0.36 6.060.090.66 SBZ6652DR Circuit #1 208-240 1,010 2+G Leads Single1606.83Self-Contained 15 15 0.36 3.902.270.66 REFRIGERATION REMOTE REFRIGERATION GLYCOL REFRIGERATION Temp (°F) Concent (%) Pressure Drop (psi)GPM Defrost Duration (Mins) Defrost Interval (Hrs)BTUHSST (°F) Model Zone Section EnvtSystem SBZ5452DR Type IISelf-Contained-R134ARefrigeratorAll N/A N/A N/A N/AN/AN/A N/A N/A N/A SBZ6652DR Type IISelf-Contained-R134ARefrigeratorAll N/A N/A N/A N/AN/AN/A N/A N/A N/A IMPORTANT NOTES 1) Units are supplied with levelers. They must be adjusted during installation to ensure the unit is level and plumb. Dimensions reflect levelers extended 1 5/8''. 2)Refer to serial label for refrigerant type. Cases built before March 2017 contain R-404a, and case built after contain R-134a. INTENDED ENVIRONMENT Type I - Designed to operate in ambient conditions of 75°F with 55% relative humidity unless noted otherwise under Envt above. WARMEST AVERAGE PRODUCT TEMP & INTENDED USE OF ZONES Intended UseTemp (°F)Zone Packaged refrigerated products 40 1 2 Unpackaged refrigerated products 40 REGULATORY All Models Accordance with AHRI Std 1200 ETL Listed to UL 471 ETL Listed to CAN/CSA 22.2 No. 120 NSF Std 7 Listed 888 E. Porter Rd. Muskegon, MI 49441 231-798-8888 Revised 3/30/2017 20480348 Foodservice DID 16238 - MODEL SBZ6652DR DID 16239 - MODEL SBZ5452DR Technical Information - Oasis - Combination Non-Refrigerated Service Above Refrigerated Self -Service Case Page 2 of 2 888 E. Porter Rd. Muskegon, MI 49441 231-798-8888 Revised 3/30/2017 20480348 Foodservice DID 16238 - MODEL SBZ6652DR DID 16239 - MODEL SBZ5452DR RECOMMENDED PARTS LIST ZEPHYR MODELS SBZ6652DR and SBZ5452DR DESCRIPTION SCC PART #QTY MAGNETIC FILTER 83644 1 MAIN POWER SWITCH 5-5000 1 LIGHT SWITCH 75785 1 CONTACTOR -- 30A 220V 20-04881 1 COND FAN MOTOR 77422 2 COMPRESSOR #NT6217GKV for R-404a cases 20-13399 1 COMPRESSOR #FFU160HAX for R-134a cases 20-69989 1 TXV VALVE #EFSE-1/2-CP115 for R-404a cases 20-13510 1 TXV VALVE #EFJE-1/4-JCP for R-134A cases 72645 1 EVAP FAN MOTOR 5-9055 4 WICKING MATERIAL 83358 2 REAR DOOR SEAL KIT 20-75369 1 THERMOMETER 20-09795 1 MODEL SBZ6652DR ONLY 66 1/4" L REAR ACRYLIC DOOR - RIGHT HAND 20-52858 1 REAR ACRYLIC DOOR - LEFT HAND 20-52859 1 LED BULB 42K 20-75466 1 GLASS TOP ASSEMBLY REPLACEMENT KIT with DOORS 20-61427 1 MODEL SBZ5452DR ONLY 54 1/4"L REAR ACRYLIC DOOR - RIGHT HAND 20-59558RH 1 REAR ACRYLIC DOOR - LEFT HAND 20-59558LH 1 LED BULB 42K 20-75464 1 GLASS TOP ASSEMBLY REPLACEMENT KIT with DOORS 20-63997 1 DID 16238 - MODEL SBZ5452DR DID 16239 - MODEL SBZ6652DR Features • Application storage capacity from 242 lbs (110 kg) to 854 lbs (388 kg). • Multiple bin tops provide an easy solution for mounting ice makers on different sized bins. • Polyethylene bin liner is insulated with foam for maximum ice preservation — 1.5" to 3" (38 mm to 76 mm). • 31" deep for use where space is at a premium. • Built-in ice scoop holders on certain models. • Sturdy leg design — 6" (152 mm) adjustable NSF approved legs — standard. • Durable stainless finish. SLOPE FRONT STORAGE BINS SL O P E F R O N T S T O R A G E B I N S Ice. Pure and Simple Ordering and Specification Information — Required Bin Top/Cover Bin Model No. Application Bin Storage lbs (kgs) Approximate Shipping Weight lbs (kgs) ICE Series™ Cube Ice Makers Nugget Ice Makers Flake Ice Makers 22" (559 mm) wide 30" (762 mm) wide 48" (1,219 mm) wide 21" (533 mm) wide 21" (533 mm) wide B25PP*242 (110)74 (34)KBT19 <<N/A KBT19 KBT19 B40PS 344 (156)103 (47)KBT19 <<N/A KBT19 KBT19 B42PS 351 (160)99 (45)<<N/A N/A KBT24 KBT24 B55PS 510 (232)125 (57)KBT19 <<N/A KBT19 KBT19 B110PS 854 (388)163 (74)N/A BPF-1 <<KBT23 KBT23 << Kit not required. Hold down securement recommended. Bin Height includes 6" (423 mm) legs. All bins have polyethylene liners. *Rotocast finish *Rotocast finish Bin Accessories Ice-O-Matic Part Number Description 1011517-22 Plastic ice shovel 1011517-23 Hanging bracket for ice shovel 1011517-24 46.5" Plastic paddle 1051517-29 Hanging bracket for ice paddle 9051127-01 82 Ounce ice scoop B55 Ordering and Specification Information — Side by Side Bin Model No.Style Application Bin Storage lbs (kgs) Approximate Shipping Weight lbs (kgs) ICE Series™ Cube Ice Makers Nugget Ice Makers Flake Ice Makers Two 22" (559 mm) wide Two 30" (762 mm) wide Two 48" (1,219 mm) wide Two 21" (533 mm) wide Two 21" (533 mm) wide B25PP*Slope Front 242 (110)74 (34)N/A N/A N/A N/A N/A B40PS Slope Front 344 (156)103 (47)N/A N/A N/A N/A N/A B42PS Slope Front 351 (160)99 (45)N/A N/A N/A N/A N/A B55PS Slope Front 510 (232)125 (57)N/A N/A N/A N/A N/A B110PS Slope Front 854 (388)163 (74)N/A N/A N/A KBT22 KBT22 18029 (B110 only) Rev: 07/16 Part: 3000 11100 E. 45th Avenue • Denver, CO 80239 • Phone: 1. 866. PURE. ICE • Fax: 303. 371. 6296 • www.iceomatic.com Ice. Pure and Simple SL O P E F R O N T S T O R A G E B I N S SLOPE FRONT STORAGE BINS Dimensions NOTES: Approx. Shipping Weight lbs (kg): B110 191 (87 kg) • B55 170 (77 kb) • B25 95 (43 kg) • B40 135 (61 kg) • B42 135 (61 kg) B101 Rear Bin Drain 3/4” (19mm) F.P.T. Rear Bin Drain 3/4” (19mm) F.P.T. Rear Bin Drain 3/4” (19mm) F.P.T.15” (381mm) 31” (787mm) 31” (787mm) 24” (610mm) 48” (1219mm)30” (762mm) 50” (1270mm) 6 3/4” (172mm) 6 3/4” (172mm) 44” (1118mm) 50” (1270mm)44” (1118mm) 6” (152mm) to 7” (178mm) Adjustable Legs 6” (152mm) to 7” (178mm) Adjustable Legs 15” (381mm) 31” (787mm) 30” (762mm) 28” (711mm)22” (559mm) 5 1/4” (133mm) 6” (152mm) to 7” (178mm) Adjustable Legs Rear Bin Drain 3/4” (19mm) F.P.T. 15” (381mm) 31” (787mm) 30” (762mm) 6” (152mm) to 7” (178mm) Adjustable Legs Rear Bin Drain 3/4” (19mm) F.P.T. 31” (787mm) 22” (559mm) 6” (152mm) to 7” (178mm) Adjustable Legs 6 3/4” (172mm) 50” (1270mm)44” (1118mm)11” (279mm) 37 1/2” (953mm)31 1/2” (800mm) B55 B25 B42B40 KBT19Bin Top for 30” (762mm)bins with 22” (559mm)ICE Series Cube Ice MakersGEM Series Ice Makers & MFI Series Ice Makers 23 1/2”(597mm) 48”(1219mm)30”(762mm) KBT5Bin Top for 30” (762 mm) ICE series cuber including the ICE1506 family on a B100 bin 23 1/2”(597mm) 48”(1219mm)48”(1219mm) KBT24Bin Top for 22” (559mm) bins with (1) 21” (533mm) wideGEM Series Ice Maker 23 1/2”(597mm)23 1/2”(597mm) 22”(559mm) KBT22Bin Top for 48” (1219mm) bins with (2) 21” (533mm) wideGEM Series Ice Makers& MFI Series Ice Makers 24”(610mm)24”(610mm) 48”(1219mm) KBT23Bin Top for 48” (1219mm) bins with (1) 21” (533mm) wideGEM Series Ice Makers& MFI Series Ice Makers 24”(610mm)24”(610mm) 48”(1219mm) B110 9"(229mm) 10"(254mm) 24"(610mm) BPF-1 Filler Panel for B110 bins with 30" (762mm) ICE Series Cube Ice Makers ORDERED SEPARATELYCannot be used with the B100 18029 (B110 only) Ice Machine / Ice Bin compatibility 15002 10348 18029 10738 10102 B42 B40 B110 B25 B55Design ID Description 10229 ICE MACHINE ICE1506HR REMOTE ✔✔ (2)✔ 10480 ICE MACHINE ICE1806HR REMOTE 10637 ICE MACHIN CUBE AIR COOL 210LB (1)(1)(1)(1)(1) 15008 ICE MACH ICE1506HT AIR COOL TV ✔✔ (2)✔ 18835 ICE MACHINE CIM0430HA 115V ✔✔ (2)✔✔ 18836 ICE MACHINE CIM0520HA 115V ✔ 18837 ICE MACHINE CIM0530HA 115V ✔✔ (2)✔✔ 18838 ICE MACHINE CIM0530HW 115V ✔✔ (2)✔✔ 18839 ICE MACHINE CIM0636HA 230V ✔✔ (2)✔✔ 18840 ICE MACHINE CIM0836HA 208-230V ✔✔ (2)✔✔ 18842 ICE MACHINE CIM1136HA 208-230V ✔✔ (2)✔✔ 18843 ICE MACHINE CIM1136HR 208-230V ✔✔ (2)✔✔ 18844 ICE MACHINE CIM1136HW 208-230V ✔✔ (2)✔✔ 18845 ICE MACHINE CIM1446HA 208-230V ✔ 18846 ICE MACHINE CIM1446HR 208-230V ✔ 18847 ICE MACHINE CIM1446HW 208-230V ✔ 19729 ICE MACHINE CIM2046HR 208-230V ✔ (1) - Self-contained ice bin (2) - Requires BPF-1 ice bin adapter kit Design ID Ice Bin model No longer available - replaced by CIM2046HR 5 11/16 [144]R3/4 [R19]8 3/16 [208] 1 3/16 [29] Ⱦ1 3/8" [35] DRAIN HOLE TO BE DIMPLED MIN. 1/8" [3] IN DEPTH TO ENSURE BRASS DRAIN FITS FLUSH 16 3/8 [416] WRAP 16 3 / 1 6 [ 4 1 1 ] 16 [ 4 0 6 ] R3/4 [R19] 11 3/8 [289] WRAP 12 5 / 1 6 [ 3 1 3 ] 15 [381] 17 5/16 [440] 10 [ 2 5 4 ] TUB TO BE DIE STAMPED TO A MINIMUM 1/4" [6] DEPTH TO ENSURE PROPER DRAINAGE 6 5 / 8 [ 1 6 8 ] W E L D ST U D P L A C E M E N T 1 11/16 [43] 11 3/4 [299] WELD STUD PLACEMENT 1 5/8 [41] LID NOT SHOWN IN TOP VIEW12 9 / 1 6 [ 3 1 9 ] 17 9/ 1 6 [ 4 4 6 ] DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 1 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 Ⱦ1/4 [6] 1 [ 2 5 ] 8 1 / 2 [ 2 1 6 ] 13 1/ 2 [ 3 4 3 ] 1 [25 ] 1 [25] Ⱦ7/8 [22] ATTACH TO INSULATED WRAP BY MEANS OF 4 EACH WELD STUDS AND STUD CAPS PERFORATED TRIVET ALL CORNERS FULLY WELDED AND POLISHED 18 GA. [1.2] CONSTRUCTION PERFORATED TRIVET TO FIT INSIDE TUB RADIUS AND HAVE FINGER HOLES FOR REMOVAL BIN SECTION VIEWS 17 5/16 [440] 16 3/8 [416]11 3/8 [289] 12 5/16 [313] 1 1/2 [38] 1 1/4 [32] 2 [51] 11/16 [18] 7/16 [10] 7/16 [10] 16 3 / 1 6 [ 4 1 1 ] 1" NPS BRASS DRAIN WITH FLANGED ZINK LOCKNUT AND RUBBER WASHER 5/ 8 [ 1 6 ] 5/ 8 [ 1 6 ] 7/16 [11] Ⱦ1 3/8" [35] DRAIN HOLE TO BE DIMPLED MIN. 1/8" [3] IN DEPTH TO ENSURE BRASS DRAIN FITS FLUSH 14 GA. [2.0] CONSTRUCTION TOP 16 GA. [1.5] CONSTRUCTION TUB FULLY WELDED AND POLISHED TO A 304 #4 FINISH 20 GA. [1.0] 304 S/S CONSTRUCTION WRAP TO BE INSULATED WITH 1/2" [13] FOIL FACED RIGID FOAM AT SIDES AND BOTTOM (SILICONE ALL SEAMS) Ⱦ2 5/8" [Ⱦ67] BY 1/2" [13] TALL S/S RING STITCH WELDED TO INSIDE OF WRAP (SILICONE INSIDE SEAM) FUSE WELD 1" [25] LONG WELD STUD TO BOTTOM OF INNER TUB Ⱦ3/8" [Ⱦ10] HOLES IN INSULATION AND WRAP FOR WELD STUD WELD STUD AND CAP DETAIL Scale: N.T.S. DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 2 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 LID ASSEMBLY SECTION 3/4" RADIUS HALF ROLLED RAISED INTEGRAL HANDLE WITH EASED CORNERS FRONT LID SECTION 3 7/8 [99] 3 [76] LID CLOSED 5/ 8 [ 1 6 ] 12 9/16 [319] 3 3/8 [86] LID OPEN 1/2 [13] 1 3 / 4 [4 4 ] DETAIL -B- PAGE 4 OF 4 6 [152] NSF STICKER (COMPONENT) 16 GA. [1.5] 304 #4 S/S LID FRAME 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION A A FULLY WELD & POLISH ALL CORNERS 13 [ 3 3 0 ] (2) 1/4"x1/2" [6x13] S/S THREADLESS WELD STUDS W/ (2) ADDITIONAL TACK WELDS 15 [ 3 8 1 ] I.D . 10 [2 5 4 ] I.D. 17 9 / 1 6 [ 4 4 6 ] 12 9/ 1 6 [ 3 1 9 ] 5/8 [16] 1/2 [13] 1 5/16 [33] SECTION A-A SCALE: NTS NOTE: SECTION TYP. @ 4 SIDES 3/16 [5] 11/16 [18] 5/8 [16] MARINE EDGE DETAIL Scale: NTS DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 3 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 4 1/4 [108] O.D. 15 5 / 1 6 [ 3 8 9 ] O. D . 11/16 [17] 1/2 [13] DIE STAMP UP 1/8" MINIMUM R3/4 [R19]4 3/16 [107] O.D. 1 7/16 [37] 3 13/16 [97] 1/2 [13] DIE STAMP UP 1/8" MINIMUM 1 [25] BACK FLANGE W/ 2 EA. HOLES TO SLIDE OVER THREADLESS WELD STUDS 15 1 1 / 1 6 [ 3 9 9 ] O. D . 3 3/8 [86] O.D. DIE STAMP UP 1/8" MINIMUM 15 1 / 2 [ 3 9 4 ] O. D . 3 7/8 [99] O.D. 11/16 [18] 11/16 [18] 2 1/8 [54] O.D. 5/ 8 [1 6 ] 11/16 [17] 7/16 [11] DETAIL -B- DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 4 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 Horizon Elite™ remote 1810, 2110 series Chewblet® ice machine Short form specification: Ice machine to be a Follett® Horizon Elite ice machine model ______________ [Insert size/series, condenser type and installation/ mounting, from model number guide] capable of producing compressed nugget ice using an efficient, sanitary horizontal evaporator/auger system and delivering ice by a flexible wire reinforced transport tube to ice storage bin, ice and water dispenser, ice and beverage dispenser, drop‑in dispenser or Ice Manager™ diverter valve system, slide‑out evaporator with utility docking station, front‑mounted unit status display, evaporator water inlet at harvest end with automatic flush while producing ice, and semi‑automatic cleaning and sanitizing system, plus all the features listed below and mounting/performance‑enhancing accessories checked. 801 Church Lane | Easton, PA 18040, USA 1.800.523.9361 | 1.610.252.7301 | follettice.com 1 Independent third party studies. Contact Follett for details. 2 Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice. ³ Refer to price list for additional warranty information. Features Horizon Elite 1810 series ‑ up to 1784 lb (810 kg) in 24 hours 2110 series ‑ up to 2039 lb (925 kg) in 24 hours ‑ automatically transport ice through a tube with RIDE® technology from up to 75' (22.9 m) away ‑ chewable, compressed nugget ice is preferred over cubes¹ ‑ Chewblet ice dispenses reliably from ice and beverage dispensers ‑ available with approximately 1.00" (2.54 cm) long standard Chewblet ice or optional 3/8" (0.95 cm) long Micro Chewblet™ ice ‑ quiet production without noisy harvest cycles Revolutionary, scale inhibiting design ‑ produces ice that has 15% the TDS of the incoming water for optimum dispensing and long life in drinks ‑ quarantines and regularly expels scale producing dissolved solids to dramatically reduce scale buildup ‑ increases time between descaling and reduces or eliminates the need for expensive scale treatment ‑ saves 35% water compared to comparable cubers ‑ three phase models ENERGY STAR® certified Durable, attractive ice machine ‑ regular bearing inspection or replacement is not required ‑ upgraded, easy‑to‑read LED operating status and diagnostic display Designed with sanitation in mind ‑ Agion® silver‑based antimicrobial product protection of key ice and water contact components² ‑ floatless, sealed design inhibits formation of biofilms ‑ semi‑automatic cleaning and sanitizing system Warranty ‑ 3 years parts and labor, 5 years compressor parts ³ Certifications Model configurations For use with 1 Install/ mount Condenser Evaporator Item number 2 1810 series Item number 2 2110 series ice storage bin top mount with 115/60/14, 5 HCD1810RBT HCD2110RBT without 115/60/1 HCD1810NBT HCD2110NBT RIDE with 115/60/1 4, 5 HCD1810RBS HCD2110RBS without 115/60/1 HCD1810NBS HCD2110NBS Follett Vision™ undercounter ice and beverage dispenser RIDE with 115/60/1 4, 5 HCD1810RVS HCD2110RVS without 115/60/1 HCD1810NVS HCD2110NVS countertop ice and beverage dispenser (by others) top mount 3 with 115/60/1 4, 5 HCD1810RHT HCD2110RHT without 115/60/1 HCD1810NHT HCD2110NHT RIDE with 115/60/1 4, 5 HCD1810RHS HCD2110RHS without 115/60/1 HCD1810NHS HCD2110NHS drop-in dispenser (by others)RIDE with 115/60/1 4, 5 HCD1810RJS HCD2110RJS without 115/60/1 HCD1810NJS HCD2110NJS Ice Manager diverter valve system RIDE with 115/60/14, 5 HCD1810RMS HCD2110RMS without 115/60/1 HCD1810NMS HCD2110NMS ¹ Ordered separately. ² For Micro Chewblet ice, replace second character (C) with an M e.g. HMD2110RBT. ³ Requires top kit (see page 5 for part number). ⁴ Condensing unit is 208-230/60/1. ⁵ For three phase remote condensing unit, replace third character (D) with an F e.g. HCF1810RBT. 23181, 23182 23181 HMD2110RBT 23182 HMD1810RBT 2 Form# 8180 Remote 1810, 2110 series ice machine Specification, evaporator unit Horizon Elite 1810 series Horizon Elite 2110 series W1 Width 22.70" (57.7 cm) Fits on 22.00" wide dispensers 22.70" (57.7 cm) Fits on 22.00" wide dispensers D1 Depth 23.70" (60.2 cm)23.70" (60.2 cm) H1 Height 22.50" (57.2 cm)22.50" (57.2 cm) Clearance top, left and right – 1.00" (2.54 cm)top, left and right – 1.00" (2.54 cm) C1 Electrical 115 V/60/1 5 amps, requires dedicated 15 amp circuit, 6' (1.8 m) cord, NEMA 5‑15 plug 5 amps, requires dedicated 15 amp circuit, 6' (1.8 m) cord, NEMA 5‑15 plug Operating power 368 W 368 W C2 Ice transport tube see page 7 for details see page 7 for details C3 Water inlet 3/8" OD push‑in water inlet – internal connection 3/8" OD push‑in water inlet – internal connection C4 Drain 3/4" MPT, 1" drain required see page 7 for details 3/4" MPT, 1" drain required see page 7 for details C5 Ice bin signal cord for Vision applications only for Vision applications only C6 Liquid line 3/8"3/8" C7 Suction line 7/8"7/8" Air temperature 50 ‑100 F (10 ‑ 38 C)50 ‑100 F (10 ‑ 38 C) Water temperature 45 ‑ 90 F (7 ‑ 32 C)45 ‑ 90 F (7 ‑ 32 C) Potable water pressure 10 ‑ 70 psi (69 ‑ 483 kPa)10 ‑ 70 psi (69 ‑ 483 kPa) Ice production see ice production chart on page 8 see ice production chart on page 8 Energy consumption 90 F (32 C) air, 70 F (21 C) water single phase – 4.59 kWh three phase – 3.33 kWh per 100 lb (45.4 kg) ice single phase – 4.65 kWh three phase – 2.93 kWh per 100 lb (45.4 kg) ice Water consumption 12.4 gal (47 L) of potable water per 100 lb (45.4 kg) of ice (per AHRI test standards). 13.9 gal (53 L) at low TDS flush setting. 12.4 gal (47 L) of potable water per 100 lb (45.4 kg) of ice (per AHRI test standards). 13.9 gal (53 L) at low TDS flush setting. Refrigerant R404a R404a BTU/hr (Kcal/hr) at 0 F (‑18 C) evaporator, 90 F (32 C) ambient air 15,700 (3,956)18,200 (4,586) Rack systems EPR valve set point EPR valve to be supplied by installer 0 F (‑18 C)0 F (‑18 C) Approximate ship weight 170 lb (77 kg)175 lb (79 kg) Approximate net weight 160 lb (73 kg)165 lb (75 kg) NOTE: For indoor use only. Outdoor installation of evaporator unit is not recommended and will void warranty. Dimensional drawingAccessories Top kit for ice and beverage dispensers (page 5) Water filters (refer to form# 9905) Wall mount bracket (item# 00997098) Ice machine stand, height‑adjustable (item# 00997080) Timer to control one or two ice machines (item# 00967265) Longer ice transport tube (refer to price list, form# 4025) NOTE: 10' (3 m) provided as standard for RIDE model. Sleep cycle kit for improved energy efficiency and component life (item# 01338276) NOTE: For countertop dispenser applications for models ending in HS and HT. Insulated 35' (10.7 m) refrigeration lines (item# 00977785) – (not pre‑charged) for 1810R and 2110R SafeCLEAN Plus™ ice machine cleaner 1 x 8 oz (237 ml) bottle (item# 01147826) 6 x 8 oz (237 ml) bottles (item# 01149954) 24 x 8 oz (237 ml) bottles (item# 01149962) SaniSponge™, 24 sanitary sponges (item# 01075431) W1D1 H1 C1 C1 C2 C7 C6 C3 C4 C5 Back View 22.00" (55.9 cm) 22.69" (57.6 cm) 2.73" (6.93 cm) 2.28" (5.79 cm)6.04" (15.34 cm) 19.59" (49.76 cm) 16.00" (40.64 cm) L2 L1 G 23181, 23182 3 Form# 8180Remote 1810, 2110 series ice machine Specification, condenser unit Horizon Elite 1810 series Horizon Elite 2110 series W1 Width 30.00" (76.2 cm) – all models 30.00" (76.2 cm) – all models D1 Depth (hail guard included)38.50" (97.8 cm) – all models 38.50" (97.8 cm) – all models H1 Height 25.75" (65.4 cm) – all models 25.75" (65.4 cm) – all models Electrical single phase – 208‑230/60/1 three phase – 208‑230/60/3 single phase – 208‑230/60/1 three phase – 208‑230/60/3 Operating power single phase – 6.0 kW three phase – 3.6 kW single phase – 6.2 kW three phase – 4.6 kW Minimum circuit ampacity single phase – 26.2 A three phase – 15.7 A single phase – 27.1 A three phase – 19.9 A Maximum circuit HVACR breaker size single phase – 45 A three phase – 25 A single phase – 45 A three phase – 30 A Outdoor condensing unit operating limits (air temperature) min ‑20 F (‑29 C) max 120 F (49 C) min ‑20 F (‑29 C) max 120 F (49 C) Maximum refrigerant line run length 75' (22.9 m)75' (22.9 m) Maximum line rise above evaporator 35' (10.7 m)35' (10.7 m) Evaporator mounting above condenser 15' (4.6 m)15' (4.6 m) Maximum refrigeration line drop without oil trap 15' (4.6 m)15' (4.6 m) Refrigerant charge 14.5 lb required at installation 14.5 lb required at installation Approximate ship weight 305 lb (138 kg)305 lb (138 kg) Approximate net weight 295 lb (134 kg)295 lb (134 kg) NOTE: 1. Suction line must be insulated. Liquid line does not require insulation. W1 D1 H1 Dimensional drawing 23181, 23182 4 Form# 8180 Remote 1810, 2110 series ice machine 1 – Locating the ice machine Horizon Elite remote Chewblet ice machines allow top‑mounting or mounting in a base cabinet, on a wall or on a floor stand up to 75' (22.9 m) from the dispenser or ice bin with RIDE technology. In‑cabinet mounting (RIDE applications) require special attention to service access, unit ventilation and ice tube runs (see pages 6‑7). Top mounting – ice and beverage dispensers (by others) RIDE model – Follett low-profile Vision ice and beverage dispensers Top mount on Follett ice storage bins Important specifier notes Important specifier notes Important specifier notes 1. Dispenser must be compatible with nugget ice. See page 5 for compatible ice and beverage dispenser models and top kit numbers. 2. Verify ceiling or soffit height to ensure sufficient top clearance. 1. See page 6 for critical clearance requirements. 2. Ice transport tube ships with Vision ice and beverage dispenser (Vision applications only). 1. See form# 8590 for bin sizing. 2. Verify ceiling or soffit height to ensure top clearance. 3. Locate floor sink or grate and drains in front of storage bin. 4. Do not position bin drain lines to block Ice•DevIce™ bin cart. RIDE model – ice and beverage dispensers (by others) RIDE model – drop-in beverage dispensers (by others)RIDE model – Follett ice storage bins Important specifier notes Important specifier notes Important specifier notes 1. Dispenser must be compatible with nugget ice. Compatible dispensers include Cornelius DB/ED/DF150/175, Lancer 4500‑22N, FS‑16N and FS‑44N, Servend MD150/175/200/250 SV150/175/200/250 and Follett Symphony Plus™ 110CM, as well as dispensers listed on page 5. 2. Coca‑Cola Freestyle 7100 requires top adapter IC Code 46751 and ice kit IC Code 46430 only, and must be ordered from Coca‑Cola. Coca‑ Cola Freestyle 9100 requires top kit HSF26SC. Consult with Coca‑Cola and Follett to qualify application prior to ordering. 3. RIDE application is approved only for Pepsi Spire 3.0, 5.0 and 4.1 designed for top mount ice machines and requires MSP24SC for 3.0 and MSP30SC for 5.0 and 4.1, ordered separately. For manual fill versions of Pepsi Spire 3.0, 5.0 and 4.1, contact factory. 4. See page 6 for critical clearance requirements. 1. Compatible with the following dispensers: Cornelius 1522, 1722, 2323 and Lancer 2200, 2300, 23300. 2. Requires 12.00" (30.5 cm) of access space for installation on transport tube side. 3. See page 6 for critical clearance requirements. 1. See form# 8590 for bin sizing. 2. Locate floor sink or grate and drains in front of storage bin. 3. Do not position bin drain lines to block Ice•DevIce bin cart. 23181, 23182 5 Form# 8180Remote 1810, 2110 series ice machine 1 – Locating the ice machine (continued) Top mounting – compatible ice and beverage dispensers 1 Manufacturer Model Number Width in (cm) Depth 2 in (cm) Height 3 in (cm) Top kit Coca‑Cola dispensers Freestyle 7000 30.10 (76.5) 33.11 (79.0) 47.00 (119.4)H22F30‑F 4 Freestyle 7100 30.00 (76.2) 33.80 (85.8) 47.00 (119.4)H22F30‑F 4, 5 Freestyle 9000 25.50 (64.8) 35.50 (90.2) 73.75 (187.3)H22F24‑F 4, 6 Freestyle 9100 25.50 (64.8) 39.25 (99.7) 77.2 (196.2)H22F26‑F 4 Cornelius dispensers DB/ED/DF 200 series 30.00 (76.2) 30.00 (76.2) 34.38 (87.3) H22C30‑F or H22C30‑X 7 DB/ED/DF 250 series 30.00 (76.2) 30.00 (76.2) 38.38 (97.5) H22C30‑F or H22C30‑X 7 DB/ED/DF 300 series 44.00 (111.8) 30.00 (76.2) 34.00 (86.4) H22C44‑(F or B) 8 FlavorFusion/Overload 30.00 (76.2) 30.70 (78.0) 39.38 (100.0)H22C30‑F‑FF IDC215 30.00 (76.2) 30.70 (78.0) 39.38 (100.0)H22C30‑F‑IDC IDC255 and Pro Fast Gate 30.00 (76.2) 30.70 (78.0) 36.38 (92.4)H22C30‑F‑IDC IDC Pro 30.00 (76.2) 33.13 (84.2) 40.25 (102.2)H22C30‑X‑PRO ⁹ Lancer dispensers 4500‑30N 30.00 (76.2) 30.50 (77.5) 36.50 (92.7) H22L30‑(F or B) 8 FS‑22N 22.00 (55.9) 30.50 (77.5) 42.13 (107.0)H22L22‑F FS‑30N 30.00 (76.2) 30.50 (77.5) 42.13 (107.0) H22L30‑(F or B) 8 Bevariety 30.00 (76.2) 31.00 (78.7) 37.75 (95.9)H22L30‑F‑STP Sensation 30"30.00 (76.2) 31.00 (78.7) 38.25 (97.2)H22L30‑F‑STP Sensation 44"44.00 (111.8) 31.00 (78.7) 39.38 (100.0)H22L44‑F‑STP Touchpoint 32.50 (82.55) 33.70 (85.6) 40.00 (101.6)H22L30‑F‑STP Pepsi dispensers Spire 3.0 27.00 (68.6) 35.00 (88.9) 38.12 (96.8)H22P24‑F Spire 5.0 / 4.1 30.50 (77.5) 36.00 (91.4) 42.75 (108.6)H22P30‑F Servend dispensers MDH‑302 42.75 (108.6) 31.00 (78.7) 32.38 (82.2) H22S44‑(F or B) 8 MDH‑402 60.00 (152.4) 30.50 (77.5) 32.38 (82.2) H22S60‑(F or B) 8, 10 1 All approved dispensers can be filled with a RIDE model Horizon Elite ice machine without a top kit except for Pepsi Spire 3.0, 5.0 and 4.1, see page 4 for details. 2 Requires minimum 0.50" (1.27 cm) clearance between back of dispenser and wall. 3 Net height after installation of top kit (excluding height of ice machine). 4 Consult with Coca-Cola and Follett to qualify application prior to ordering. 5 Top adapter IC Code 46753 and ice kit IC Code 46430 must also be ordered from Coca-Cola. 6 Adapter must also be ordered from Coca-Cola. KO IC Code: 46010 (Silver), 46011 (Red) or 46012 (Black). 7 Top designed with flexibility to accommodate front or back mounting. 8 Specify “F” for front facing, or ”B“ for backward facing units. ⁹ Top designed with flexibility to accommodate front or back mounting. 10 60-inch models: Please specify number of Horizon Elite ice machines and location. D = 2; R = 1 on right side; L = 1 on left side. 23181, 23182 6 Form# 8180 Remote 1810, 2110 series ice machine 3 – Horizon Elite ice machine mounting accessories Optional wall mount bracket Optional machine stand Important specifier notes 22.00" (55.9 cm) 25.50" (64.8 cm)23.00" (58.4 cm) A C DB 6.88" (17.5 cm) A - 15.875" (40.3 cm) B - 19.375" (49.2 cm)C - 13.00" (33.0 cm) D - 21.00" (53.3 cm) 1. For secure wall mounting, specify optional wall mount bracket. 2. Wall and fasteners must support the weight of the ice machine, bracket, supply water and ice. Use of a backing board may be required with hollow wall construction. 3. Machine stand mounting adds 6.88" (17.5 cm) to height of ice machine. 4. No dips in tube routing allowed. 5. Ice transport tube needs minimum 1/4" per foot (2 cm per meter) pitch toward ice machine and should be secured to prevent dips and traps from forming. 2 – Undercounter/in-cabinet mounting Cabinet details Important specifier notes Cabinet base must be ﬂat and free of obstructions (no lip or utilities to block removal) Cabinet door opening 24.00"W x 23.5"H (60.9 cm x 59.7 cm) minimum slidesout Ice transport tube secure to prevent dipsand traps from forming 12.00" (30.5 cm) minimum between ice machine and dispenser minimum 1/4" per foot(2 cm per meter)pitch toward ice machine 1. Cabinet door opening must meet minimum size requirements shown and be free of obstructions to allow ice machine to slide out (no lip or utilities to block removal). 2. Cabinet base must be capable of supporting ice machine and allow ice machine to rest flat on cabinet bottom. 3. No counter supports, electric or plumbing can run in front of the ice machine. 23181, 23182 7 Form# 8180Remote 1810, 2110 series ice machine 5 – Horizon Elite ice tube runs - specifier guidelines Long tube runs for RIDE remote ice delivery equipment 1/4" 1' maximum 2' (60.9 cm)beverage dispenser wall-mountedice machine support straps transport tube slope (toward ice machine) (2 cm per meter) minimum of 6.00" (15.24 cm) turn/cornerradius ice transport tube –1 3/16" OD,2 1/8" OD with insulation Important specifier notes 1. 75' (22.9 m) maximum ice transport tube run. 2. Tubing routing bends must have a 6.00" (15.24 cm) radius or larger. 3. Dips and traps are not allowed. If not supported from underneath, secure insulated ice transport tube at least every 2' (60.9 cm) to prevent drips and traps. 4. Relative humidity levels above 80% in areas where the ice machine or ice transport tube is located may produce excessive condensation that will cause water damage. 5. Contact factory for recommendations on running tubing through a decorative soffit or chase. 4 – Horizon Elite drain - specifier guidelines Flush drain plumbing – For regular machine drainage Important specifier notes: Where code allows, follow recommendation below. ➌ ➊ 3/4" barb x 3/4" FPT 1" Stand pipe/drain 2 ft x 1" ODsilicone tubing Minimum 8" radius 3/4" MPT x 1" slip ➋ 1. Connect the silicone tubing to the ice machine 3/4" drain barb ➊. 2. Assemble the 3/4" barb x 3/4" FPT to the 3/4" MPT x 1" slip. Connect the other end of the silicone tubing to the 3/4" barb ➋. 3. Connect the 1" slip fitting to the 1" stand pipe/ drain ➌. Note: Minimum 8" radius on silicone drain line. Drain line from the ice machine must have at least 1/4" per foot pitch (6.4 mm/0.3 m). Note: Stand pipe/drain provided by others. All other components provided with ice machine. Chassis drain plumbing – To assist with condensate in high humidity areas Important specifier notes: Where code allows, follow recommendation below. 1. Plug must be removed from John Guest fitting. 2. Route 3/8" drain tubing through knockout in back of docking station and insert fully into John Guest fitting connection at the rear of the machine chassis. Route other end of 3/8" drain tubing to drain. 3. Drain must slope 1/4" inch per foot (6 mm per 30.4 cm). 23181, 23182 Remote 1810, 2110 series ice machine 801 Church Lane | Easton, PA 18040, USA 1.800.523.9361 | 1.610.252.7301 | follettice.com8180‑202205 | © Follett Products, LLC Ice production – Horizon Elite 1810 series Inlet water temperature F (C) Ambient air temperature F (C) 60 (16) 70 (21) 80 (27) 90 (32) 100 (38) lb ( k g ) p r o d u c t i o n i n 2 4 h r 50 F (10 C)1859 (844) 1784 (810) 1685 (765) 1616 (734) 1500 (681) 60 F (16 C)1723 (782) 1684 (765) 1578 (716) 1563 (710) 1409 (640) 70 F (21 C)1620 (735) 1594 (724) 1514 (687) 1420 (645) 1319 (599) 80 F (27 C)1550 (704) 1487 (675) 1485 (674) 1351 (613) 1299 (590) 90 F (32 C)1471 (668) 1435 (651) 1370 (622) 1285 (583) 1207 (548) Ice production – Horizon Elite 2110 series Inlet water temperature F (C) Ambient air temperature F (C) 60 (16) 70 (21) 80 (27) 90 (32) 100 (38) lb ( k g ) p r o d u c t i o n i n 2 4 h r 50 F (10 C)2039 (925) 2039 (925) 1934 (877) 1825 (828) 1703 (772) 60 F (16 C)1943 (881) 1888 (856) 1878 (852) 1710 (776) 1584 (718) 70 F (21 C)1833 (831) 1781 (808) 1789 (811) 1634 (741) 1489 (675) 80 F (27 C)1754 (796) 1686 (765) 1643 (745) 1535 (696) 1426 (647) 90 F (32 C)1650 (748) 1603 (727) 1577 (715) 1457 (661) 1395 (633) ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Agion is a registered trademark of Sciessent LLC. HORIZON ELITE, ICE•DEVICE, ICE MANAGER, MICRO CHEWBLET, SAFECLEAN PLUS, SANISPONGE, SYMPHONY PLUS and VISION are trademarks of Follett Products, LLC. CHEWBLET, FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. Remote condensing unit Condensing unit installation specifications Important specifier notes air in exhaust 48.00" (121.9cm) 48.00" (121.9cm)24.00" (61.0cm) 24.00" (61.0cm) 36.00" (91.4 cm) height clearance 1. Provide front, back, top and side clearances as shown. 2. The maximum refrigerant line run length is 75' (22.9 m). Installations require 14.5 lb of refrigerant. 3. The maximum line rise above the evaporator is 35' (10.7 m). Condensing unit above evaporator unit – 35' (10.7 m) (installations with rise over 20' (6.1 m) require additional suction line s‑trap at midpoint rise). 4. The evaporator can only be mounted a maximum of 15' (4.6 m) above the condensing unit. Note: The service loop is not included when calculating length, rise or drop in the tubing run. Note: To connect evaporator/ice machine to rack systems, see page 3. 23181, 23182 1034-20230804 | © Follett Products, LLC 801 Church Lane | Easton, PA 18040, USA 1.800.523.9361 | 1.610.252.7301 | follettice.com HORIZON ELITE and Ice Manager are trademarks of Follett Products, LLC. FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. Bin Tops for Horizon Elite™ (no Ice Manager™) pedestal mount for Ice-O-Matic B55/B110 bin Bin top with pedestal mount specification W1 Width B55H22H30 – 30.02" (76.3 cm) B110H22H30 – 48.02" (122.0 cm) D1 Depth 21.29" (54.1 cm) D2 Depth 24.48" (62.2 cm) H1 Overall height of pedestal 9.91" (25.2 cm) H2 Additional height added to bin after installation 8.70" (22.10 cm) Net weight B55H22H30 – 45 lb (20 kg) B110H22H30 – 56 lb (25 kg) Approximate ship weight B55H22H30 – 47 lb (21 kg) B110H22H30 – 58 lb (26 kg) W1 H1 D1 D2 H2 Model configurations – Bin top with pedestal mount Description Number of ice machines Bin Width Item number Bin top with pedestal mount for Follett Horizon Elite on Ice-O-Matic B55 bin 1 B55 30"B55H22H30 Bin top with pedestal mount for Follett Horizon Elite on Ice-O-Matic B110 bin 1 B110 48"B110H22H30 Bin top with pedestal mount DID 23338 DID 23337 23337, 23338 Ice Machine Pedestal for Ice-O-Matic Bin 01541986R02 © Follett Products, LLC 2/23 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.com Installation Instructions The following parts are shipped with the bin top: Part #Description Qty Part #Description Qty 01541747 Pedestal End 2 01541606 Channel, Pedestal 2 201937 Screw, Cap, Hex Hd, 1/4-20 X 3/4"4 01478700 Screw, 10-32 x 1/2" Lg 6 01541721 Cover Plate (for use with 22" wide ice machines only) 1 200864 Nut, Hex, 1/4-20 4 01541689 Stiffener, Pedestal 1 200874 Washer, Flat, 1/4", 5/8" OD 4 01541614 Stiffener, Pedestal 1 206796 Thumbscrew, #8 x 1/2"2 207332 Bolt, Carriage, 1/4-20 X 1/2" Lg 16 205561 Washer, Flat, 9/32" ID, use with Thumbscrew 2 200875 Washer, Lock, 1/4"20 202123 Sealant, 4.7 oz tube 1 201004 Nut, Acorn, 1/4-20 16 207801 Gasket, 60 in.1 01541630 or 01541648 Bin Top, 48" or 30"1 The ice machine pedestal is adjustable and can accommodate both a 30" and 48" wide bin. The pedestal is also adjustable to accommodate a variety of Follett Horizon Elite ice machines. As an example, and for reference, the figure below shows the pedestal assembled to fit a 48" wide bin and a Horizon Elite 22"-wide ice machine. To adjust the pedestal to fit a 30" wide bin, the Pedestal Ends are attached to the Pedestal Channels using the inner-most holes of the Pedestal Channel. To accommodate a different Horizon Elite ice machine, the stiffeners are simply reoriented and placed in the appropriate location. Pedestal End Bin Top Stiffener Stiffener Pedestal Channel Carriage bolt, 1/4-20 x 1/2", lock washer, acorn nut Screw, 10-32 x 1/2" Hex head screw, 1/4-20 x 3/4", flat washer, lock washer, hex nut Pedestal Channel Cover Plate1 Pedestal End 1 Cover Plate used only with this 22"-wide ice machine docking station. 23337, 2333823337, 23338 2 Ice Machine Pedestal for Ice-O-Matic Bin Procedure 1.Ensure that the bin top is removed from the bin. 2.Place Pedestal Ends on flat surface (floor), and turn them upside down. 3.Place the Pedestal Channels inside the Pedestal Ends. The slots in the Pedestal Channels and Pedestal Ends must align. 4.Using 16 1/4-20 x 1/2" carriage bolts and choosing the holes that accommodate the bin width, loosely hand-tighten the Ends to the Channels. Note: Do not tighten the bolts of the pedestal frame until the pedestal is correctly mounted on the ice bin. 5.Mount the pedestal on top of the bin gasket. 6.Align pedestal with rear wall of bin. 7.Ensure that the bottom flange of the Pedestal Ends are snug against the bin wall. 8.Place the ice maker Stiffeners into the cutouts based upon the ice machine configuration. 9.Ensure that the Pedestal Ends are level, then fully tighten the 16 carriage bolts. Note: Pay attention to how the orientation of the Stiffeners differs depending on which type of ice machine is being mounted. 48" PEDESTAL WITH 22" REMOTE-CONDENSING ICE MACHINE - MUST USE COVER PLATE 30" PEDESTAL WITH 22" REMOTE-CONDENSING ICE MACHINE - MUST USE COVER PLATE FOURTH SLOT SECOND SLOT 23337, 2333823337, 23338 Ice Machine Pedestal for Ice-O-Matic Bin 3 48" PEDESTAL WITH 30" SELF-CONTAINED ICE MACHINE - DO NOT USE COVER PLATE 30" PEDESTAL WITH 30" SELF-CONTAINED ICE MACHINE - DO NOT USE COVER PLATE THIRD SLOT FIRST SLOT 10.For 22"-wide ice machine docking stations, place the Cover Plate (with the large hole towards the rear and offset to the left of the bin) over the Stiffeners and align the holes. 11.Using the instructions shipped with the ice machine: §Mount the docking station to the rails (and Cover Plate, if applicable) and bolt in place. §Mount the ice machine to the docking station ensuring the drain tube is fully seated on the drain barb connection. §Install the drain and auxiliary chassis drain. §Make the electrical and potable water connections. 23337, 2333823337, 23338 4 Ice Machine Pedestal for Ice-O-Matic Bin 12.Once the ice machine installation is complete, locate the three holes on the left side, and three holes on right side of the pedestal flange. 13.Install mounting hardware to secure the pedestal to the bin side wall. §Use a 5/32" drill bit with a 1/4" drill stop installed to create pilot holes. Do not drill through interior bin wall. §Install (6) #10-32 x 1/2" screws. 14.Remove the existing gasket from the top front of the bin. 15.Slide bin top under pedestal and into place, ensuring that the rear flange is over the rear of the bin. 16.Pull bin top forward until the rear flange is tight against the rear of the bin. 17.Using a pencil or marker, trace the front edge and side edge of the bin lid to mark where the new gasket will be placed. 18.Remove the bin lid and apply the new gasket so that the bin lid front and sides will rest on the gasket. 19.Use the included sealant to seal all gasket joints and ends. 20.Reinstall the bin top and secure the rear of the bin top with the two thumbscrews and 9/32" ID washers. 21.Ensure there are no gaps where the bin top meets the gasket. 22.Using the instructions shipped with the ice machine: §Mount the shuttle actuator to the bin top. §Install the ice transport tube onto the shuttle actuator. 23337, 23338 Ice Machine Pedestal for Ice-O-Matic Bin 5 23.Per NSF, seal all seams of the frame using the sealant provided. Ensure sealant has a smooth finish. §All bolt heads and their oblong slots. §All seams (in entirety) where Pedestal Ends meet the Pedestal Channels. §All seams (in entirety) where Stiffeners meet the Pedestal Ends and/or Pedestal Channels. §All seams (in entirety) where Pedestal Ends meet the bin, both front and back (rear). §All seams (in entirety) where Cover Plate meets Stiffeners and Pedestal Channels (if applicable). 23337, 23338 6 Ice Machine Pedestal for Ice-O-Matic Bin Ice Machine Refer to the instructions shipped with the ice machine. Bin Top The top side of the bin top can be cleaned with a stainless steel cleaner such as 3M* Stainless Steel Cleaner & Polish or equivalent. * 3M is a registered trademark of 3M Company in the US and other countries. The underside of the bin top should be sanitized using a clean cloth and the same solution used to sanitize the ice machine. Pedestal The pedestal, underside of ice machine and/or Cover Plate should be cleaned and sanitized prior to use and periodically with any cleaning and sanitizing products suitable for use in a food zone.. Removing the Bin Top for Maintenance or Cleaning 1.Turn off the ice machine. 2.Reach in through the bin door and unscrew the large nut holding the shuttle actuator. 3.From above, pull the shuttle actuator out of the bin lid. 4.Unscrew the thumbscrews at the back of the bin top. 5.Lift up on the front of the bin top, then raise the back of the bin top as well. 6.Carefully slide the bin top out from underneath the pedestal. Cleaning and Sanitizing Procedure 23337, 23338 01"alk s. Specification Ice storage capacity 50 lb (22.7 kg) Width 21.31" (54.13 cm) Depth, upper cover 22.57" (57.33 cm) Depth, ice chute 18.85" (47.88 cm) Height 25.80" (65.53 cm) Service clearance 12.00" (30.50 cm) top 115 V/60/1 electrical 4 amps, 8' (2.4 m) cord, NEMA 5-15 450 Drain 3/4" M PT Utility connection location through bottom Minimum span —wall bracing required 16.00" (40.64 cm) on center in most applications NOTE: Wall mount bracket standard Approximate net weight 100 lb (45 kg) Approximate ship weight 118 lb (54 kg) NOTE: For indoor use only FOLLETT is a registered trademark of Follett Products, LLC, registered in the U5. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. ID50 50 lb metered ice dispenser Dimensional drawing Front View �21.31" (54.13 cm)-----0' 25.80" (63.53 cm) 4.60" G O O (11.68cm)� 00000 If Bottom View 18.85" (47.88 cm) 1.06" 1.50" ° (2.69 cm) (3.81 cm) 9.63" (24.46 cm) F 11.04" (28.04 cm) 12.13" _� (30.81 cm) Right Side View " 801 church Lane I Easton, PA 18040, USA o 9040-20230725 1 © Follett Products, LLC 1S O O 1.800.523.9361 1 1.610.252.7301 1 follettice.com 23421 Project Price Quantity Total Shipping ECL-NS-A34P Surface Mount Stainless Steel Starbucks Tall Hot Paper Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-A34P (SKU #194318) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.2 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (41 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 526 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-A34P 23” 4.000” 3.688” 3.750” 1.375” 9.000”Tall Hot Paper Cup “D” “E” “F” “A” ISSUED: REVISED: MODEL No: Accessory Specialties AMERICAN DISPENSER Desert Ray Products ,INC. THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE SURFACE MOUNTED TWIN HIDE-A-ROLL TOILET TISSUE DISPENSER 0030AMERICAN SPECIALTIES, INC. www.americanspecialties.com 441 Saw Mill River Road, Yonkers, NY 10701 (914) 476-9000 01-87 01-08 SPECIFICATION Surface Mounted Twin Hide-A-Roll Toilet Tissue Dispenser shall hold and dispense two (2) standard or two (2) 5- 1/4" diameter (Ø133) 1800 sheets tissue rolls and shall have door, door frame, and dispensing mechanism fabricated of alloy 18-8 stainless steel, type 304, 18 gauge; cabinet body shall be same grade, 22 gauge. All exposed surface shall be No 4 satin finish and be protected during shipment with a PVC film easily removable after installation. Internal mechanism levers shall be fabricated of molded high-impact resistant plastic for smooth operation. Structural assembly of body and door components shall be of welded construction. Door hinge shall be of heavy-duty stainless steel 3/16" diameter (Ø4.8). Door shall be held closed with a tumbler lock keyed alike to other ASI washroom equipment. Cabinet shall include theft resistant and vandal resistant rollers that shall be of molded high-impact resistant plastic with integral molded-in stainless steel end pins and two (2) rollers [p/n R-004] shall be supplied. Surface Mounted Twin Hide-a-Roll Toilet Tissue Dispenser shall be Model No 0030 as manufactured by American Specialties, Inc. 441 Saw Mill River Road Yonkers, New York 10701-4913 INSTALLATION Unit is surface mounted on wall or partition using four (4) No10 self-tapping screws (by others). Top two mounting holes through back are “keyhole” slots for ease in hanging unit on pre-installed screws. Bottom two mounting holes are horizontal slots for ease of adjustment. For compliance with ADA Accessibility Guidelines, top of unit should be installed 29" (737 mm) above finished floor. OPERATION Reloading instructions are printed on graphic label inside door. Bottom roll is depleted prior to top roll automatically dropping into lower position for use. Empty rollers can not be removed without key unlocking door. 6" [152] 12" [305] 2-12" [64] 7" [178] 3" [76] 1-12" [38] PIN TUMBLER LOCK MOUNTING HOLES CONCEALED ON REAR WALL HINGE PIVOT 3" [76] 6-12" [165] 11-7 8" [302] 5-3 4" [146] NOTE: ALL DIMS ARE INCH [MM] 10099 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 1/24/14 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2014 by Gamco Commercial Restroom Accessories, A Division of Bobrick. Rear View 2" 51mm 11" 279mm 8" 203mm 15-3/4" 400mm 4" 102mm 1-9/16" 40mm 1-9/16" 40mm Av e r a g e M o u n t i n g H e i g h t O f f F l o o r 45 " t o 5 9 " 1 1 4 5 t o 1 5 0 0 m m Av e r a g e M o u n t i n g H e i g h t O f f F l o o r Fo r A c c e s s i b l e D e s i g n 30 " t o 4 5 " 7 6 0 t o 1 1 4 5 m m S S Finish Face of Wall surface mounted seat-coVer dIsPenser tsc-1 materIaLs: 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. All-welded construction with beveled opening. oPeratIon: Dispenses single- or half-fold paper toilet seat covers from beveled opening. Dispenser fills from bottom through concealed opening. Capacity: 250 toilet seat covers. InstaLLatIon: Mount unit on wall or toilet partition with two flat-head screws, not furnished by manufacturer, at points indicated by an S. For plaster or dry wall construction, provide concealed backing that complies with local building codes, then secure unit with flat-head screws not furnished. For other wall surfaces, provide fiber plugs or expansion shields for use with screws, not furnished, or provide 1/8'' (3mm) toggle bolts or expansion bolts. Note: Provide a 5'' (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection to provide room for filling dispenser from bottom. sPecIfIcatIon: Surface-mounted toilet-seat-cover dispenser shall be type-304, 22-gauge (0.8mm) stainless steel with all-welded construction; exposed surfaces shall have satin finish. Dispenser shall have a concealed opening in bottom for filling. Capacity shall be 250 paper toilet seat covers Surface-Mounted Seat-Cover Dispenser shall be TSC-1 of Gamco Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK ISSUED: REVISED: MODEL No: Accessory Specialties AMERICAN DISPENSER Desert Ray Products ,INC. THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE AMERICAN SPECIALTIES, INC. 6-05441 Saw Mill River Road, Yonkers, NY 10701 (914) 476-9000 1-87 0477 SPECIFICATION Recessed Toilet Seat Cover Dispenser shall hold and dispense 500 standard single or half-fold paper toilet seat covers contained in supply box and shall have cabinet, frame and door fabricated of alloy 18-8 stainless steel, type 304, No 22 gauge; all exposed surfaces shall have No 4 satin finish protected during shipment with a PVC film which shall be easily removable after installation. Face trim frame shall be one piece construction 1" (25.4mm) wide with no welded miters and shall have a 1/4" (6.35mm) return to wall. Cover dispensing slot shall have a fully deburred flat edge for snag-free dispensing and user safety. Door shall be attached to face frame with a full-length, heavy-duty 3/16" dia. (4.8mm) stainless steel multi-staked piano hinge and shall be held closed with a tumbler lock keyed alike to other ASI washroom equipment. Structural assembly of cabinet and door components shall be of welded construction and shall have no exposed fasteners or welded seams. Recessed Toilet Seat Cover Dispenser shall be Model No 0477 as manufactured by American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701-4913 INSTALLATION Unit is mounted in wall recess using four (4) No 10 self tapping screws (by others). Mounting holes are provided in side and rear walls of cabinet and are accessible through door for installation. Note that top of dispenser slot is 2-1/2" (64mm) below top of rough wall opening. Rough Wall Opening required is.... 15-3/4"W x 11-1/4"H x 2-5/8"D. (400mm x 285mm x 67mm). OPERATION Covers are self-feeding until supply is depleted. Unit is manually reloaded with a full box through access door. RECESSED TOILET SEAT COVER DISPENSER 10172 Project Price Quantity Total Shipping ECL-NS-299P Surface Mount Stainless Steel Starbucks Short Hot Paper Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-299P (SKU #194320) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.0 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (39 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 500 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-299P 23” 3.625” 3.312” 3.406” 1.375”9.000” Short Hot Paper Cup “D” “E” “F” “A” Lo c a l l y So u r c e d Th i s ite m or sim i l a r Lo c a l l y So u r c e d Th i s ite m or sim i l a r AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com 9 32" DIA [Ø7] HOLES WITH .40" DIA [Ø10.2] X 82° COUNTERSINK TO ACCOMMODATE #10 (M5) FLAT HEAD SCREWS OR 1/4" (M6) PAN HEAD SCREWS 120° 18" [3] 3" DIA [Ø76] PEENED OPTION NOTE: ALL DIMS INCH [MM] 1-14" DIA [Ø32]1-12" [38] FINISHED WALL 2-14" DIA [Ø57] BC THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE 1-1/4" DIA (Ø32) GRAB BAR SERIES WITH FLANGES FOR EXPOSED MOUNTING MODEL №: 3400 ISSUED: 01/87 REVISED: 6 Dec 2012 SPECIFICATION Grab Bar with Flanges for Exposed Mounting shall be type 304 stainless steel alloy 18-8. Tubing shall be 1-1/4" diameter (Ø32) x 18 gauge [0.048"] (1.2). Flange shall be 11 gauge 1/8" (3) thick and shall be Heliarc welded to tubing with a continuous concealed bead. Flanges shall have three (3) countersunk 9/32" diameter (Ø7) holes to accommodate 1/4" diameter [Ø6] pan head or № 10 self-tapping flat head or oval head mounting screws (not provided). All exposed surfaces shall have a satin finish and shall be protected during shipment with a plastic bag. For optional non-slip surface add suffix –P (peened). 1-1/4" Diameter (Ø32) Grab bar with Flanges for Exposed Mounting shall be Series № 3400 of American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701- 4913 STRENGTH ASI Grab Bars are designed to meet and exceed ADA requirements as published in CABO/ANSI A117.1 and 2010 ADA Accessibility Standards. Mounting to the wall is a critical part of the system to meet this require- ment. To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fas- tener system must be adequately sized. INSTALLATION Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using three (3) № 10 self-tapping flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange. Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing. For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" (840) minimum above finished floor (AFF) to 36" (915) maxi- mum AFF. Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series). 10769 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE GRAB BAR CONFIGURATIONS (PG 1 OF 3) MODEL №: GRABBAR CONFIG ISSUED: 09/96 REVISED: 6 Dec 2012 SCHEDULE QTY. DIM. A QTY. DIM. A 12" [305] 36" [914] 18" [457] 42" [1067] 24" [610] 48" [1219] 30" [762] SCHEDULE QTY. DIM. A 52" [1321] 54" [1372] 60" [1524] 72" [1829] TYPE -01 TYPE -02 TYPE -04 TYPE -15 SCHEDULE QTY. HAND LH RH LH SHOWN RH OPPOSITE MODEL № MUST SPECIFY -LH OR -RH 33" [838] 30" [762] 3" [76] PROJECTION BELOW FINISHED FLOOR CONTRACTOR TO PROVIDE PROPER SLEEVE IN FLOOR X 3" LONG TO ACCEPT BAR OD SPECIFIED. 28" [711] 32" [813] 18" [406] 90° 1-1/2" [38] ALL DIMS INCH [MM] A 10769 Project Price Quantity Total Shipping ECL-NS-845P Surface Mount Stainless Steel Starbucks Grande/Venti Cold Plastic Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-845P (SKU #194319) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.5 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (45 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 573 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-845P 23” 4.500” 4.062” 4.188” 1.375”9.000”Grande/Venti Cold Plastic “D” “E” “F” “A” Project Price Quantity Total Shipping ECL-NS-31P Surface Mount Stainless Steel Starbucks Grande/Venti Hot Paper Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-31P (SKU #194322) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.2 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (41 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 526 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-31P 23” 4.000” 3.688” 3.750” 1.375” 9.000”Grande/Venti Hot Paper Cup “D” “E” “F” “A” Project Price Quantity Total Shipping ECL-NS-422P Surface Mount Stainless Steel Starbucks Tall Cold Plastic Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-422P (SKU #194321) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.3 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (42 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 536 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-422P 23” 4.188” 3.812” 3.938” 1.375” 9.000” Tall Cold Plastic Cup “D” “E” “F” “A” AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com 9 32" DIA [Ø7] HOLES WITH .40" DIA [Ø10.2] X 82° COUNTERSINK TO ACCOMMODATE #10 (M5) FLAT HEAD SCREWS OR 1/4" (M6) PAN HEAD SCREWS 120° 18" [3] 3" DIA [Ø76] PEENED OPTION NOTE: ALL DIMS INCH [MM] 1-14" DIA [Ø32]1-12" [38] FINISHED WALL 2-14" DIA [Ø57] BC THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE 1-1/4" DIA (Ø32) GRAB BAR SERIES WITH FLANGES FOR EXPOSED MOUNTING MODEL №: 3400 ISSUED: 01/87 REVISED: 6 Dec 2012 SPECIFICATION Grab Bar with Flanges for Exposed Mounting shall be type 304 stainless steel alloy 18-8. Tubing shall be 1-1/4" diameter (Ø32) x 18 gauge [0.048"] (1.2). Flange shall be 11 gauge 1/8" (3) thick and shall be Heliarc welded to tubing with a continuous concealed bead. Flanges shall have three (3) countersunk 9/32" diameter (Ø7) holes to accommodate 1/4" diameter [Ø6] pan head or № 10 self-tapping flat head or oval head mounting screws (not provided). All exposed surfaces shall have a satin finish and shall be protected during shipment with a plastic bag. For optional non-slip surface add suffix –P (peened). 1-1/4" Diameter (Ø32) Grab bar with Flanges for Exposed Mounting shall be Series № 3400 of American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701- 4913 STRENGTH ASI Grab Bars are designed to meet and exceed ADA requirements as published in CABO/ANSI A117.1 and 2010 ADA Accessibility Standards. Mounting to the wall is a critical part of the system to meet this require- ment. To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fas- tener system must be adequately sized. INSTALLATION Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using three (3) № 10 self-tapping flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange. Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing. For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" (840) minimum above finished floor (AFF) to 36" (915) maxi- mum AFF. Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series). 10862 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE GRAB BAR CONFIGURATIONS (PG 1 OF 3) MODEL №: GRABBAR CONFIG ISSUED: 09/96 REVISED: 6 Dec 2012 SCHEDULE QTY. DIM. A QTY. DIM. A 12" [305] 36" [914] 18" [457] 42" [1067] 24" [610] 48" [1219] 30" [762] SCHEDULE QTY. DIM. A 52" [1321] 54" [1372] 60" [1524] 72" [1829] TYPE -01 TYPE -02 TYPE -04 TYPE -15 SCHEDULE QTY. HAND LH RH LH SHOWN RH OPPOSITE MODEL № MUST SPECIFY -LH OR -RH 33" [838] 30" [762] 3" [76] PROJECTION BELOW FINISHED FLOOR CONTRACTOR TO PROVIDE PROPER SLEEVE IN FLOOR X 3" LONG TO ACCEPT BAR OD SPECIFIED. 28" [711] 32" [813] 18" [406] 90° 1-1/2" [38] ALL DIMS INCH [MM] A 10862 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 5/02/12 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2012 by Gamco Commercial Restroom Accessories, A Division of Bobrick. 8-1/4" 210mm 4-3/4" 121mm 3" 76mm 7/8" 22mm Finish Face of Wall Av e r a g e M o u n t i n g H e i g h t O f f F l o o r 44 " 1 1 1 8 m m ConstruCtion: Stainless steel tank-type soap dispensers have 40-fl oz. (1.2-L) capacity. Units are easily filled from top through locked opening. Satin-finished 22-gauge (.759mm) tanks are welded to stainless steel backs. Unit has concealed backplate and sight level indicator. Valve is black molded plastic push button with antibacterial-soap-resistant plastic cylinder and stainless steel spring. CapaCity: 40-fl oz. (1.2-L) of liquid lotion soaps, synthetic detergents and antiseptic solutions. Non-removable filler cap at top of unit is keyed to resist vandalism. instaLLation: Mount wallplate flat side against wall surface with 3- #7 x 3/4" (19mm) panhead zinc plated steel screws provided. Unlock filler cap. Back off machine screw which goes through back panel of unit. Slip dispenser over wall plate and tighten machine screw until secure. overaLL Dimensions: 8-1/4" W x 4-3/4" H x 3" D (210 x 121 x 76mm) valve projects 7/8" (22mm). aDa GuiDe: Mounting location for push button dispensers are 44" (1118mm) maximum above the finish floor. Push buttons and pistons should be operable with one hand and without tight grasping, pinching, or twisting of the wrist. Activation of soap valves should not require more than 5 pounds of force when unit is completely filled. notes: Wood blocking is preferable behind all wall surfaces. If wood blocking is not available, the following fasteners are suggested: Tile/Masonry - Plastic or lead anchors Plaster/Drywall - Toggle bolts Surface-Mounted Horizontal Tank-Type Soap Dispenser with All-Purpose Valve shall be Model G-58AP of GAMCO Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK surfaCe-mounteD horizontaL tank-type soap Dispenser with aLL-purpose vaLve G-58ap Date: Project Name: Lo c a l l y So u r c e d Th i s ite m or sim i l a r Lo c a l l y So u r c e d Th i s ite m or sim i l a r Lo c a l l y So u r c e d Th i s ite m or sim i l a r Starbucks Coffee Kent Seattle, WA | www.starbucks.com printed:8/5/2020 COMBI-FOLD PAPER TOWEL DISPENSER BY GP PRO (GEORGIA-PACIFIC), BLACK, 1 DISPENSER This durable and versatile plastic folded paper towel dispenser holds up to 400 C-Fold, 600 multifold or one package of BigFold® towels to provide a cost-effective solution for washroom paper towel dispensing. This attractive, stylish black commercial paper towel dispenser complements any decor and the covered key-lock design protects against waste and pilferage while making refilling towels quick and easy. Description: The Combi-Fold Paper Towel Dispenser gives you all the options for cost-effective paper towel dispensing. This durable, versatile commercial paper towel dispenser holds up to 400 C-Fold, 600 Multifold or 1 package of BigFold® paper towels, giving you refilling choices while helping minimize the need for maintenance, thanks to its high capacity. It’s designed for high-use areas, with durable plastic construction that’s made to last. The covered key-lock design helps protect against waste and pilferage, while making refilling the dispenser quick and easy. Features & Benefits: »DURABLE PLASTIC CONSTRUCTION, ideal for high-traffic areas »HIGH-CAPACITY COMMERCIAL PAPER TOWEL DISPENSER holds up to 400 C-Fold, 600 multifold or one pack of BigFold® towels to help minimize run-outs »ECONOMICAL & VERSATILE, dispenses M-, Z- or C-fold paper towels »KEY LOCK helps reduce waste & pilferage »COMPATIBLE with Pacific Blue Select™ (20389, 21000) & Pacific Blue Basic™ (20204, 23304) M-Fold, Pacific Blue Ultra™ (20885, 20887) Z-Fold & Pacific Blue Select™ (23000) C-Fold Paper Towels Product Details Brand Owner GP Brand Georgia-Pacific® MFG Part#56650A UP - UPC 036500311117 Each Per Ship Unit 1 Dispenser Items Per Each 0 Case Total 1 Each Dispenser (WxDxH)x x Buy Multiple 1 EA Case Shipping Info Case GTIN 10036500311114 Case Gross Wgt 3.500 LBS Case Net Wgt 3.000 LBS Case Dimensions (LxWxH) 15.938 x 12.438 x 6.250 Case Volume 0.717 CFT Unit Shipping Info TI-Qty/Layer 9 HI-Layers/Unit 16 Unit Qty 144 Unit Dimensions (LxWxH) 47.813 x 37.313 x 100.000 0 36500 31111 7 UNIT COMES WITH 1 KEY 10977 SPG MODEL No: STBKCCAD8B LK CUP CADDY (HOLDS 8 CUP DISPENSERS) m Ltr REVISION DESCRIPTION BY Dote ECO/NPR A APPROVED SHOWN HERE WITH CUP DISPENSERS PW 01.18.12 9093 c--------21.12"-----� ,-,------- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ' NOTE: CUP DISPENSERS NOT INCLUDED, SUPPLIED BY OTHERS 11.87'' ' ' o·, 'o' ) ( ' , ' , OD 7 4.76" �---�--· PROPRIETAR'I' NOTICE: Tlti<St�adamci:aljefyfbl,, 0 0 Weight 0 0 Locking Caster Cube 0 0 0 0 8 8 Fixed Caster 8 8 Description: 0 0 0 0 8 8 Swivel Non-locking Caster 30.81" .� ...... :I �p1e.uy ar 26.5 lbs. 5.18 cu.ft. STARBUCKS CUP CADOY 12x21x31H i-------'--------1 (HOLDS 8 CUP DISPENSERS) SfORI.Gf PRODUCTS GR P ;&·w 5-0RACiEP1:ilODUC1SGaOUP NTERNA'Tl:'.Jet-'1,I. U.C. /lnJper"Aft�IMs� ;-:incL'Or��brzate, m �.irz;e «d.l).b'tan ��'!.�on�d... �02D1D S,�A:Dtt.a.�..p. ri� File Name: 104097_S01_A-Model# STBKCCAOBBLK Date: Material· Finish: 09.29. 10 ALUMINUM BLACK Drawn By: Drawing Size: Scale; Sheet: Rev: Sketch No. PW A NG 1 of l A 104097 13330 SPG MODEL No: STBKCCADSBLK Ai Carriage Bolt QTY:4 B� Lock Washer QTY:4 c� Wing Nut QTY:4 Caddy Top QTY: 1 D Caddy Base QTY: 1 E CUP CADDY (HOLDS 8 CUP DISPENSERS) Ltr REVISION DESCRIPTION A APPROVED B UPDATED PACKAGE TO SHOW TOOTH-LOCK WASHER jA I @;/ I I BY Date ECO/NPR PW 01.10.12 9093 JSW 01.18.13 9093 ............ PROPRIETARY NOTICE: �11".e,etccdam.o:t.1(jefrt�l, Weight Cube Description: ASSEMBLY INSTRUCTTONS (15104097) ,_2_6_.5_lbs_.�_5·_1B_cu_.f_t. _, STARBUCKS CUP CADDY 12x21x31H .::111 ..... � STD E PRODUCTS GR P -�-pre� ·,oar S ORAGE flliDOlJCTE, GaOUP NT�"Tl;)M,_.\l... LlC. /1,r,rJper-..oo..xa;izaOis·meiet i1n4'«��1:.r=..,te ro!S-'..cb51n;,, u�7c,?1itm ��ii: st1e,eton� �oi!l1[l, S�·Pmd:d.QQ:;ct,. r!� Ale Name: (HOLDS 8 CUP DISPENSERS) 104097 _l01-B-Model# STBKCCADBBLK Date: Material: Rnlsh: 08 .10.11 ALUMINUM BLACK Drawn By: Drawing Size: Scale: Sheet: Rev: Sketch No. PW A NTS 1 of 2 B 104097 13330 SPG MODEL No: STBKCCADSBLK NOTE: CUP DISPENSERS NOT INCLUDED, SUPPLIED BY OTHERS I ---- CUP CADDY (HOLDS 8 CUP DISPENSERS) Ltr REVISION DESCRIPTION A APPROVED BY Date ECO/NPR PW 01.10.12 9093 B UPDATED PACKAGE TO SHOW TOOTH-LOCK WASHER JSW 01.18.13 9093 ··�--1 · .:�•1 .... ::11 sro E PRODUCTS GR p PROPRIETARY NOTICE: Tht.-stitttalida'm.o:dl�I,, �� ooor ST0R.\GE Pfil08UCTSGROUP NTEfiNA"TIJKI\L, u.c. 1Wjper-..on�:ali1Ji·� and.'or��b�..ue .oo �.u:.earQ4'l..:atan �� shffl:on� �O�D1D· ::.��Gro.=-1). rt� Hot Cold Weight Cube Description: ASSEM BLY INSTRUCTTONS (15104097) .,_2_6_.5 _lb_s_. �5_·1_B_c_u.f_t. _, STAR BUCKS CUP CADDY 12x21x31H Ale Name: (HOLDS 8 CUP DISPENSERS) 104097 _l01-B-Model# STBKCCADBBLK Date: Material: Rnlsh: 08.10.11 ALUMINUM BLACK Drawn By: Drawing Size: Scale: Sheet: Rev: Sketch No. PW A NTS 2 of 2 B 104097 13330 Project Price Quantity Total Shipping ECL-NS-69P Surface Mount Stainless Steel Starbucks Trenta Cold Plastic Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-69P (SKU #TBD) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.6 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (46 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 575 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully support the dispenser and allows tool-free removal for cleaning. “A”“B”“C” “D” “E”“F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-69P 23” 4.625” 4.3125” 4.375” 1.375” 9.000”Trenta Cold Plastic Cup “D” “E” “F” “A” Other_13584_Doc1 3 GALLON STORAGE TANK AEB P/N 29750PS 20403 J O E TA P K I T S P E C COMPONENTS: Joe Tap collars with 2 pieces/kit (set of 1L + 1R). Badge(1pc CN+1pc NCB)/kit & 2pcs wood handleDESIGN ID 22627 J O E TA P K I T S P E C COMPONENTS: Joe Tap collars with 2 pieces/kit (set of 1L + 1R) Badge(1pc CN+1pc NCB)/kit 2pcs wood handle DESIGN ID 22627 Back Bar Collar 1 2 3 Screw (2x) O-ring (2x) Badge (2x)Handle (2x)Right Collar (1x) Remove x2 Left Collar (1x) Back Bar Collar - JoeTap Left Right Phillips screwdriver required for assembly DESIGN ID 22627 4 Completed Assembly Back Bar Collar - JoeTap DESIGN ID 22627 Ltr I REVISION DESCRIPTION BY Date ECO/NPR STB KWT2Y A ORIGINAL PW 02.15,06 7573 B ADDED NSF LOGO PW 02.15,06 C REMOVE BIN MARKER & BIN MARKER INSERT SI 8.11.06 8662 SHELVING INTERNA710NAL STORAGE SYSTEMS 11230 Harland Drive Covington, Georgia 30209 PH: (770) 787-9830 FAX: (770) 787-6165 MOl HI ON FRONT ELEVATION BILL OF MATERIALS ITEM QTY. PART NO. DESCRIPTION 1 1 GRWM2424Y WALL—TRAX GRID 24x24 W/MOUNTING BRACKETS 2 2 GSL1424Y WALL—TRAX FLAT SHELF w LIP 14x24 3 2 PHKZ POT HOOK NOT SHOWN PROPRIETARY NOTICE: International Storage Systems, a division of Leggett & Platt, claims proprietary rights on the contents disclosed on this drawing and all processes, equipment, components, methods, or any other developments either directly or indirectly related to this project. This drawing is issued in confidence for engineering purposes only and may not be reproduced or used to manufacture anything shown hereon without direct 'written' authorization from International Storage Systems to the user. Description: Decimals: ,02 Fractions: +/— 1/32" ABOVE 3—COMP. SINK / .XXX .010 Angles: +/— 1/2' + - File Name: 101810_S01_C— MODEL#: STBKWT2Y Date: Scale: Material: Finish: 03.20.02 1 NTS I GOLD BOND PW 1 of 1 1 C 1 101810 IS103446 - 01/09/07 10416 REVISION DESCRIPTION BY Date ORIGINAL PP 5.21.04 REVISED TEXT THROUGHOUT PIN 10.21.04 SURELOCK ASSEMBLY e SVMBOL INDICATES POST NUMBER SURELOCK(PLASTIC SLEEVE) I Is vucEo oN. MA=D mpg 7 SURELOCK(PLASTIC SLEEVEI+ 5 M FRONT ELEVATION BILL OF MATERIALS - STBKP86Z4 ITEM QTY. PART NO. DESCRIPTION 1 4 P86Z POST 86" ZINC Id BACKROOM STORAGE 8� 86" POST KIT 4-PACK t STBKP86Z4 CUSTOM WORKSTATIONS PROPRIERRYNOTICE: International Storage Systems, a division of Leggett & Platt, claims proprietary rights on the contents disclosed on this drawing and all processes, equipment, components, methods, or any other developments either directly or indirectly related to this project. This drawing is issued in confidence for engineering purposes only and may not be reproduced or used to manufacture anything shown hereon without direct 'written' authorization from International Storage Systems to the user. Tolerances: Unless Othewise Specified Description: 86" POST KIT 4—PACK BACKROOM STORAGE PN: STBKP86Z4 ______= __ __ _ Decimals: / / XX +/— .02 Fractions: + — 132" .XXX + — .010 Angles: +/— 1/2' SHELVING INTERNA710NAL STORAGE SYSTEMS 11230 Harland Drive Covington, Georgia 30209 PH: (770) 787-9830 FAX: (770) 787-6165 File Name: 102878_S01_B— Date: 5.21.04 Scale: NTS Material: Finish: Drawn By: PP Size: A Sheet: 1 of 1 Rev: B Drawing No. 102878 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 1/10/14 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2014 by Gamco Commercial Restroom Accessories, A Division of Bobrick. Finish Face of Wall S 1-5/8'' 41mm 2'' 51mm Re c o m m e n d e d M o u n t i n g H e i g h t O f f F l o o r 72 ' ' 18 3 0 m m 24'' 610mm 1/2'' 13mm specifications: Units fabricated of 20-gauge (1mm) type 304 stainless steel with exposed surfaces having a satin-finish. Mop holder molded with serrated rubber cam holders and spring loaded to insure maximum gripping ability. Holders accommodate mops and brooms from 3/4" to 1-1/4" (19 to 32mm) in diameter. oVeRaLL DiMensions: 2" H x 1/2" D x 24" L (51 x 13 x 610mm) Low Profile Mop Strip shall be Model__________________ (insert model number) of Gamco Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK Low pRofiLe Mop stRip Ms-1a 13578 Starbucks: Water Filtration Racks Date: 5.7.12 Includes: • Specification Sheets for 18x24 & 16x16 approved sizes • Assembly Instructions • Skid quantities & shipping information SPG International, LLC 11230 Harland Drive NE Covington, GA 30014 877.503.4SPG www.spgusa.com Updated: 5.7.12 Michael D. Potter michael.potter@spgusa.com * 404.823.3934 dr7 w+ MEM `:l r+ L21 STORAGE PR0WTS GROUP NUM ADJUSTABLE T-BAR SHELF WELD NOTES ANY PERSON ACCEPTING THIS SHEET AND/OR INFORMATION AGREES TO MAKE NO DISCLOSURE, USE OR DUPLICATION THEREOF EXCEPT AS DECIMALS: XX—+-.03, .XXx—+-.015 AUTHORIZED BY SPG INTERNATIONAL LLC. AND TO RETURN THIS SHEET ON REOUEST. COPYRIGHT (C) 2011 STORAGE PRODUCTS GROUP. Ap GULwx sQuAxENEss: +i_ In DEGREES- MODEL# AATB1616-8 2" CORNER BLOCK TYPx4 PLACES EE-BAR TYPx3 PLACES SIDE VIEW WITH LEGS --7 8 5/16" 6 1 /2" CLEARANCE MAX FRONT VIEW WITH LEGS dr7 w+ MEM `2 r+ L21 STORAGE PROWTS GROUP IINUM ADJUSTABLE T—BAR SHELF WELD NOTES ANY PERSON ACCEPTING THIS SHEET AND/OR INFORMATION AGREES TO MAKE NO DISCLOSURE, USE OR DUPLICATION THEREOF EXCEPT AS ANGULAR DECIMALS: QUAR NE, .max 2 DE AUTHORIZED BY SPG INTERNATIONAL LLC. AND TO RETURN THIS SHEET ON REOUEST. COPYRIGHT (C) 2011 STORAGE PRODUCTS GROUP. Ap GULwx SQUARENESS: +i_ n DEGREES MODEL# AATB1824-8 SIDE VIEW WITH LEGS .-. - - / _ 17 TEE -BAR � � � � � � 17 7/8° �23 7/8" TYPxS PLACES CORNER BL( TYPx4 PIA( 6 1 /2" 8 5/16" CLEARANCE MAX FRONT VIEW WITH LEGS AS S E M B L Y I N S T R U C T I O N S AA T B 1 6 1 6 - 8 & A A T B 1 8 2 4 - 8 ST E P 1 : UN B O X S H E L F A N D ( 4 ) LE G S . W I T H 3 / 1 6 TH AL L E N WR E N C H L O O S E N S C R E W S UN T I L C L E A R O F S H E L F SO C K E T . T H E W I D E S I D E O F T - BA R I S T H E T O P S I D E O F S H E L F . ST E P 2 : IN S E R T L E G T O DE S I R E D H E I G H T A N D F I R M L Y TI G H T E N S E T S C R E W . I N M O S T CA S E S T H E T O P O F T H E PL A S T I C C A P S H O U L D B E SH O W I N G ST E P 3 : RE P E A T B O T H S T E P S 1 AN D 2 O N A L L F O U R C O R N E R S OF U N I T . L E G S C A N B E AD J U S T E D A S N E E D E D F O R UN L E V E L F L O O R S . SP G I n t e r n a t i o n a l , L L C 11 2 3 0 H a r l a n d D r i v e N E Co v i n g t o n , G A 3 0 0 1 4 87 7 . 5 0 3 . 4 S P G ww w . s p g u s a . c o m 53 1/2" Height 48" Length 40" Width TOLERANCES UNLESS OTHERWISE SHOWN: DECIMALS: .XX=+/-.03, .XXX=+/-.015 ANGULAR SQUARENESS: +/- 1/2 DEGREES FRACTIONS: +/-1/16" THIS SHEET AND THE PRODUCTS CONTAINED THEREIN ARE THE EXCLUSIVE PROPERTY OF: STORAGE PRODUCTS GROUP INTERNATIONAL, LLC. ANY PERSON ACCEPTING THIS SHEET AND/OR INFORMATION AGREES TO MAKE NO DISCLOSURE, USE OR DUPLICATION THEREOF EXCEPT AS AUTHORIZED BY SPG INTERNATIONAL LLC. AND TO RETURN THIS SHEET ON REQUEST. COPYRIGHT (C) 2011 STORAGE PRODUCTS GROUP. Skid will hold 84 Units of either 18x24 or 16x16 sizes. Total weight w/ Pallet for 16x16 units: 649 lbs Total weight w/ Pallet for 18x24 units: 796 lbs Skid Skid Plan View GENERAL TOLERENCESIN ACCORDANCE WITHISO 2768-M 5.5" X 9.5" CUT OUT 13 2X 10 9 4X 1 8 7 2X 12 2X 11 14 3X 2 2X 3 4X 33.8 858 15.7 398 153X 18.55 4719.75 248 7.63 194 3X 27.1 689 40.50 1029 9.75 248 6 2X REVISIONS ZONE REV.DESCRIPTION BY DATE ECO / NPR 01 CUSTOMER APPROVAL JH 1/6/2016 9407 02 CUSTOMER APPROVAL, REV #2 JH 3/4/2016 9407 ITEM NO.QTY.PART NO.DESCRIPTION DWG. NO. BILL OF MATERIALS 15 3 TBD NGFC SHELF BRACKET SHORT, LH K00512_P04 14 3 TBD NGFC SHELF BRACKET SHORT, RH K00512_P03 13 2 TBD NGFC SHELF BRACKET, LH TOP K00512_P02 12 2 TBD NGFC SHELF BRACKET, RH TOP K00512_P01 11 1 TBD 9.75" X 14.25" POLY SHELF CUT K00512_P06 10 1 TBD 14.25" x 40.50" POLY TOP, BLACK K00512_P07 9 4 TBD 9.75" X 14.25" POLY SHELF POLY BLACK K00512_P05 8 1 4H7122 DOUBLE RUNNER WELDMENT, NGFC K00512_A03 7 2 4H7121 SIDE RUNNER WELDMENT, NGFC K00512_A02 6 2 4H7124 TRAY GUARD ASSEMBLY, NGFC K00512_A05 5 8 007-0042 5/16"-18 NYLON INSERT HEX LOCKNUT_STD HW0101_P01 4 12 TBD 5/16"-18 X 1 5/8" HEX HEAD CAP SCREW_GRADE 2 HW0001_P01 3 4 4H7123 CROSSMEMBER, NGFC K00512_A04 2 2 TBD SPLASH GUARD PANEL K00512_P08 1 4 CM3MB 3" SWIVEL POLYURETHANE CASTER W/ BRAKE 100810_A01 4H7120Part No. SHEET 1 of 1 Rev. 1/6/2016 JH Material: APRD 918-3/BK/KD/MOD Drawn By: AS NOTED Finish:AS SPECIFED 02 NEXT GEN FOOD CART, 2 TIER RACK Weight: 11230 Harland DriveCovington, Georgia 30014PH: 1-800-810-9080www.spgusa.com PROPRIETARY NOTICE: This sheet contains confidential, proprietary information of Storage Product Group International LLC. Any person accepting this sheet and/or information agrees to make no disclosure, use or duplication thereof except as authorized by SPG to return this sheet on request. Copyright © 2010 Storage Product Group International. All rights reserved. T:\ENGINEERING\PROJECTS\9400 - 9499\9407- Next Gen Food Card\SWCAD\New\Narrow_Version_1\ K00512_A01 4H7120 NTS Scale: TBD Sketch No. Approved By: TBD Date: Volume: K00512_S01 Description: DIMENSIONS IN ( ) ARE REFERENCE.DIMENSIONS IN [ ] ARE MILLIMETERS, ALL OTHER DIMENSIONS ARE INCHES. NEXT GEN FOOD CART, 2 TIER RACK cu ft. lbs.DID 17255 Model# 4H7120 Mobile Pastry Cart Assembly Instructions For Questions, please call 877.503.4774 SPG International, 11230 Harland Drive NE, Covington, GA 30014 Parts list: Shelf Brackets 6 total – Lower side shelf brackets 4 total – Upper side shelf brackets (3-left hand 3- right hand) (2-Left hand 2 right hand) Required Tools: Standard Slot Screwdriver ½” Wrench (2 included) Included Hardware: Fasteners listed below Instruction Sheet Included Fasteners: 24 ea - Euro Screws 4 ea – Sheet metal screws 12 ea – 5/16” x 1 5/8” bolt 8 ea – 5/16” nylon lock nuts 17255 Aluminum parts 1 ea – Side Pan Tray assembly – With side shelf holes 1 ea – Side Pan Tray assembly – Without side shelf holes 1 ea – Middle pan tray assembly 4 ea – Cross Connector Tubes 2 ea – Tray Guards 4 ea – Casters Polymer Parts 1 ea – 14” x 41” Poly top 3 ea – 14” x 10” Poly side shelves 1 ea – 14” x 10 Poly side shelf with cutout 2 ea – 1/8” Poly Side Panels 17255 TOP Sides Shelves Pastry Cart Assembly Instructions 17255 ASSEMBLY STEPS 1.Place two Cross Connector Tubes on floor approximately 13” apart. NOTE: Flush side of tube and square collar should be on the floor. 2.Place top end of Side Pan Tray assembly into the cross connector tube assembly collars. (Top of assembly has plastic caps in tube) Slide rails should face in towards Cross Tube. 3.Insert 5/16” x 1 5/8” bolt through aligned holes in collars and tube from the outside of collar towards the middle of the assembly and thread lock nut onto both bolts 17255 4.Repeat steps 2 and 3 on opposite end using the 2nd side pan tray assembly. 5.Place cross tubes 3 & 4 onto both side pan tray assemblies with the flush side of the Cross Tube up. 17255 6.Place the casters into the square tubes with the cross member in place with holes in caster stem facing the same direction as holes in side panel tube. Align holes in cross tube collar, caster stem, and pan tray side. Insert 5/16” x 1 5/8” bolt from the outside of collar towards the middle of the side assembly and hand tighten nylon insert lock nut onto bolt. 7.Place Middle Pan Tray assembly between cross tubes and align threaded inserts with thru holes in the center of the Cross Tube assembly 8.Insert 5/16 x 1 5/8” bolt into insert and hand tighten. 17255 9.Tighten all bolts using hex wrench. 10.Carefully turn assembly over and place the unit on the previously installed casters. Hold Middle Pan Tray section in place to prevent damage. 11.Align the threaded inserts in the Middle Pan tray with through holes in the center of the Cross Tube assembly 12.Insert5/16” x 1 5/8” bolt into insert and tighten. 17255 13.Insert Poly Side Panels from top between tray runners and square cross tubes on each end. Side panels will rest on caster flanges 14.Place Tray Guard straps on the back of the cart by putting u-channel end of the strap over bottom Cross Tube in the middle of the tray openings. 17255 15.Slowly place Poly Top onto the cart. The cutouts in the top need to align with a) the bolt heads in the middle of the Cross Tube and b) the Tray Guards. 16.Once in place, attach top to the frame using included Z-brackets in 4 locations using Euro Screws 17.Attach LH and RH lower shelf brackets to side poly side solid shelves using ½” Euro screws. Attach LH and RH upper shelf brackets to one solid shelf and one shelf with cutout using ½” Euro Screws. 18.Attach Upper side shelf brackets/shelves into place using sheet metal screws and predrilled holes in Side Pan Tray vertical tubes. 17255 19. Attach Lower side shelf assemblies by placing shelf bracket hanger over side panel assembly flat bar. Hook area will fit between side plastic sheet and flat aluminum flat bar in Side Pan Tray vertical tubes. Unit is ready for use. 17255 Starbucks™ Mobile Pastry Cart Assembly Guide EVERYTHING WHERE YOU NEED IT, AND EVERYTHING IN ITS PLACE. KeLMA x 17255 Kelmax SPG Contacts Starbucks™ - SPG Account Manager Lisa Gochnour Strategic Account Manager 3340 Peachtree Road Ne Suite 1250 Atlanta, GA 30326 Phone 877.503.4774 x1458 Fax 404.709.1905 email lisa.gochnour@spgusa.com Starbucks™ - SPG Engineer James Knutson Director of engineering 11230 Harland Drive Ne Covington, GA 30014 Phone 877.503.4774 x1211 Cell 404.904.4297 email james.knutson@spgusa.com Starbucks™ - SPG Customer Service Rep. Tammy Jones Customer Service 11230 Harland Drive Ne Covington, GA 30014 Phone 800.874.0375 x1258 Fax 800.577.2210 email tammy.jones@spgusa.com Starbucks™ - SPG Headquarters Contact Michael Potter Chief Business Development Officer 3340 Peachtree Road Ne Suite 1250 Atlanta, GA 30326 Phone 877.503.4SPG x1435 Cell 404.823.3934 email michael.potter@spgusa.com Starbucks™ Mobile Pastry Cart Contact List/ Required Tools & Included Hardware 1 1-877-503-4SPG (4774) www.spgusa.com REQUIRED TOOLS 1.Philips screwdriver 2.½” Wrench (2 included) INCLUDED HARDWARE/SCREWS 1.Instruction Sheet 2.#12 x 3/4” Pan Head Sheet Metal Screw 3.M6.3-2.2 x 10mm FH Phillips Euro Screw 4.5/16”- 18 x 1 3/4” Hex Head Cap Screw 5.5/16”-18 Nylon Insert Hex Locknut 6.Z-Bracket ALUMINUM PARTS POLYMER PARTS SHELF BRACKETS 1.Side Pan Tray Assembly 2.Middle Pan Tray Assembly 3.Cross Connector Tubes 4.Tray Guards 5.Casters QTY- 2 QTY- 1 QTY- 4 QTY- 2 QTY- 4 1.14.25” x 41” Poly Top 2.14.25” x 10” Poly Side Shelves 3.14.25” x 10” Poly Side Shelf w/ Cutout 4.1/8” Poly Side Panels QTY- 1 QTY- 4 QTY- 1 QTY- 2 1.Lower Side Shelf Brackets (3- left hand, 3- right hand) 3.Upper Side Shelf Brackets (2- left hand, 2- right hand) QTY- 6 QTY- 4 * Polymer components and casters are colored blue for easier identifcation in the written instructions. The standard polymer color is black. QTY- 4 QTY- 24 QTY- 12 QTY- 8 QTY- 4 17255 Starbucks™ Mobile Pastry Cart Parts List 2 Casters (4)Side Pan Tray Assembly (2) Middle Pan Tray Assembly (1) Cross Connector Tubes (4) Tray Guards (2) Poly Side Shelves (4) Poly Side Shelf w/ Cutout (1) Poly Top (1) Poly Side Panels (2) 17255 Kelmax Starbucks™ Mobile Pastry Cart Installation Guide 3 Place two Cross Connector Tubes on floor approximately 11.25” apart. 1. 2.Place open ends of both Side Pan Tray assemblies into the cross connector tube assembly collars. (Top of assembly has plastic caps in tube) 11.25” NOTE: Flush side of tube and square collar should be on the floor. NOTE: Slide rails should face in towards Cross Tube. 17255 Starbucks™ Mobile Pastry Cart Installation Guide 4 4. 3. Insert 5/16” - 18 x 1 3/4” bolt through aligned holes in collars and tube from the outside of collar towards the middle of the assembly and thread lock nut onto both bolts. Place Middle Pan Tray assembly between cross tubes and align threaded inserts with thru holes in the center of the Cross Tube assembly. 5. Insert 5/16” - 18 x 1 3/4” bolt into insert and hand tighten. 6. Place the casters into the square tubes with the cross member in place with holes in caster stem facing the same direction as holes in side panel tube. Align holes in cross tube collar, caster stem, and pan tray side. 3 3 4 4 4 4 6 5 17255 Kelmax Starbucks™ Mobile Pastry Cart Installation Guide 5 Place cross tubes 3 & 4 onto both side pan tray assemblies with the flush side of the Cross Tube up. 7. 11.Tighten all bolts using hex wrench. Align the threaded inserts in the Middle Pan tray with through holes in the center of the Cross Tube assembly. 9. 10.Insert 5/16” - 18 x 1 3/4” bolt into insert and hand tighten. 10 9 Place Tray Guard straps on the back of the cart by putting u-channel end of the strap over bottom Cross Tube in the middle of the tray openings. 12. 12 8.Insert 5/16” - 18 x 1 3/4” bolt through aligned holes in collars and tube from the outside of collar towards the middle of the assembly and thread lock nut onto all bolts. 12 17255 Starbucks™ Mobile Pastry Cart Installation Guide 6 Insert Poly Side Panels from top between tray runners and square cross flat bar on each end. Side panels will rest on caster flanges. 13. Slowly place Poly Top onto the cart and slide attached Z-brackets onto cross bar. The cutouts in the top need to align with a) the bolt heads in the middle of the Cross Tube and b) the Tray Guards. 15. Pre-assemble 2 z-brackets in outer most holes on poly top, using euro screws. (See Diagram 14) 14. 17255 Kelmax Starbucks™ Mobile Pastry Cart Installation Guide 7 16.Once in place, attach top to the frame using included Z-brackets in remaining 2 locations using euro Screws. 17.Attach LH and RH lower shelf brackets to side poly side solid shelves using euro screws. Attach LH and RH upper shelf brackets to one solid shelf and one shelf with cutout using euro Screws. Attach Upper side shelf brackets/shelves into place using #12 x 3/4” pan head sheet metal screws in predrilled holes in Side Pan Tray vertical tubes. 18. NOTE: Bottom View NOTE: Bottom View 17255 Starbucks™ Mobile Pastry Cart Installation Guide 8 Attach Lower side shelf assemblies by placing shelf bracket hanger over side panel assembly flat bar. Hook area will fit between side plastic sheet and flat aluminum flat bar in Side Pan Tray vertical tubes. 19. Assembly Complete! Mobile Pastry Cart is ready to use!20. 17255 Kelmax Maximizing efficiency, improving performance, getting more out of your people and your investment—it’s what you must do every day to make your business more success- ful and more profitable. And it’s what SPG helps you achieve through our extensive line of innovative food service equipment. At SPG, our equipment is ergonomically designed to minimize the time, movement and effort of your staff—while maximizing the efficiency of every inch of your available space. We use the best materials for the job and manufacture to strict tolerances to ensure our equipment provides lasting performance and enduring value. As a global company, we manufacture ISS, Kelmax, Freestyle and other quality storage product lines throughout North America and the Pacific. As a result, our products are delivered to businesses throughout the world every day…and every day we continue to deliver on our promise to ensure their continuing success and profitability. Be More. Do More. www.spgusa.com ©2016 SPG International, LLC. Not just setting higher standards. Exceeding them. 17255 KELMAX 4H7120-R Guide d’assemblage du chariot à pâtisserie Starbucks™ TOUT, LÀ OÙ VOUS EN AVEZ BESOIN, ET TOUT À SA PLACE. INSTK00513_A01_C-17255 KELMAX INSTK00513_A01_C-4H7120-R Coordonnées de SPG Starbucks™ - Directrice de compte de SPG Lisa Gochnour Directrice de compte stratégique 3340 Peachtree Road NE Suite 1250 Atlanta, GA 30326 Téléphone 877.503.4774 x1458 Télécopieur 404.709.1905 Courriel lisa.gochnour@spgusa.com Starbucks™ - Ingénieur de SPG James Knutson Directeur de l’ingénierie 11230 Harland Drive NE Covington, GA 30014 Téléphone 877.503.4774 x1211 Téléphone cellulaire 404.904.4297 Courriel james.knutson@spgusa.com Starbucks™ - Représentant du service à la clientèle de SPG Tammy Jones Service à la clientèle 11230 Harland Drive NE Covington, GA 30014 Téléphone 800.874.0375 x1258 Télécopieur 800.577.2210 Courriel tammy.jones@spgusa.com Starbucks™ - Contact du siège social de SPG Michael Potter Directeur du développement commercial 3340 Peachtree Road NE Suite 1250 Atlanta, GA 30326 Téléphone 877.503.4SPG x1435 Téléphone cellulaire 404.823.3934 Courriel michael.potter@spgusa.com Chariot à pâtisserie mobile Starbucks™ Liste de contacts/ Outils nécessaires et matériaux inclus 1 1-877-503-4SPG (4774) www.spgusa.com OUTILS NÉCESSAIRES 1.Tournevis Philips 2.Clés de ½ po (2 incluses) MATÉRIEL/VIS FOURNIES 1.Fiche d’instructions 2.Vis à tête cylind. de feuille métallique #12 x ¾ po 3.Vis FH Phillips Euro M6, 3-2,2 x 10 mm 4.Vis hexagonale 5/16 po à 18 x 1 ¾ po 5.Contre-écrou à garniture de nylon de 5/16 po -18 6.Équerre en Z PIÈCES EN ALUMINIUM PIÈCES EN POLYMÈRE SUPPORTS À TABLETTES 1.Assemblage du plateau latéral du moule 2.Assemblage du plateau du moule du milieu 3.Traverses tubulaires de raccordement 4.Protecteurs du plateau 5.Roulettes Qté- 2 Qté- 1 Qté- 4 Qté- 2 Qté- 4 1.Haut en poly de 14,25 po x 41 po 2.Étagères latérales en poly de 14,25 po x 10 po 3.Étagère latérale en poly de 14,25 po x 10 po avec encoche 4.Panneaux latéraux en poly de 3/16 po Qté- 1 Qté- 4 Qté- 1 Qté- 2 1.Supports à tablettes inférieures latérales (3- du côté gauche, 3- du côté droit) 3.Supports à tablettes latérales supérieures (2- du côté gauche, 2- du côté droit) Qté- 6 Qté- 4 * Les éléments et les roulettes en polymère sont colorés en bleu pour une identification plus facile dans les instructions écrites. La couleur standard du polymère est le noir. Qté- 8 Qté- 24 Qté- 12 Qté- 8 Qté- 4 17255 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Liste des pièces 2 Roulettes (4)Assemblage du plateau latéral du moule (2) Avec bande anti-bruit Assemblage du plateau du moule du milieu (1) Avec bande anti-bruit Traverses tubulaires de raccordement (4) Protecteurs du plateau (2) Étagères latérales en poly (4) Étagère latérale en poly avec encoche (1) Haut en poly (1) Panneaux latéraux en poly (2) 17255 KELMAX INSTK00513_A01_C-4H7120-R Chariot à pâtisserie mobile Starbucks™ Guide d’installation de la bordure d’insonorisation Insérez une extrémité de la section en caoutchouc sur la glissière du plateau, juste après l’intersection entre le rayon et la section droite de la glissière en aluminium. 1. 2.En suivant la glissière, poussez la section en caoutchouc dans celle-ci. 3.Une fois en place, passez la main ou un objet dur le long de la glissière pour s’assurer que la section en caoutchouc est entièrement engagée dans la glissière en aluminium. 17255 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Guide d’installation 4 4.Insérez le boulon de 5/16 po - 18 x 1 ¾ po à travers les trous alignés dans les cols et le tube à partir de l’extérieur du col vers le milieu de l’assemblage et vissez le contre- écrou sur les boulons. Placez l’assemblage du plateau du moule du milieu entre les traverses tubulaires et alignez les inserts taraudés avec les orifices au centre de l’assemblage de la traverse tubulaire. 5. Insérez le boulon de 5/16 po - 18 x 1 ¾ po dans l’insert et serrez à la main. 6. 3 3 4 4 4 4 6 5 17255 KELMAX INSTK00513_A01_C-4H7120-R Chariot à pâtisserie mobile Starbucks™ Guide d’installation 5 Placez les traverses tubulaires sur les deux assemblages du plateau latéral du moule avec le côté plat de la traverse tubulaire vers le haut. 7. 11.Serrez tous les boulons en utilisant la clé hexagonale. Alignez les inserts taraudés dans le plateau du moule du milieu avec les trous au centre de l’assemblage de la traverse tubulaire. 9. 10.Insérez le boulon de 5/16 po - 18 x 1 ¾ po dans l’insert et serrez à la main. 10 9 Placez les courroies du protecteur du plateau à l’arrière du chariot en mettant l’extrémité de la goulotte en u de la courroie sur la traverse tubulaire du bas au milieu des ouvertures du plateau. 12. 12 8.Insérez le boulon de 5/16 po - 18 x 1 ¾ po à travers les trous alignés dans les cols et le tube à partir de l’extérieur du col vers le milieu de l’assemblage et vissez le contre-écrou sur tous les boulons. 12 8 7 7 17255 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Guide d’installation 6 Insérez les panneaux latéraux en poly à partir du haut entre les glissières du plateau et la barre plane transversale carrée à chaque extrémité. Les panneaux latéraux s’appuieront sur les rebords des roulettes. 13. Placez lentement le haut en poly sur le chariot et glissez les crochets en z fixés sur la barre transversale. Les encoches du haut doivent être alignées avec a) les têtes des boulons au milieu de la traverse tubulaire et b) les protecteurs du plateau. 15. Pré-assemblez 2 crochets en z dans les trous situés à l’extrémité extérieure sur le haut en poly, en utilisant les vis Euro. 14. 14 15 15 15 13 13 17255 KELMAX INSTK00513_A01_C-4H7120-R Chariot à pâtisserie mobile Starbucks™ Guide d’installation 7 16.Une fois en place, fixez le haut à la structure en utilisant les crochets en z inclus dans les 2 emplacements qui restent en utilisant les vis Euro. 17.Fixez les supports inférieurs LH et RH de l’étagère aux étagères latérales pleines en poly en utilisant les vis Euro. Fixez les supports supérieurs LH et RH de l’étagère à une étagère pleine avec encoche en utilisant les vis Euro. Fixez les crochets/étagères de l’étagère latérale supérieure en utilisant les vis à tête cylindrique de feuille métallique #12 x ¾ po dans les trous percés à l’avance dans les tubes verticaux du plateau latéral du moule. 18. REMARQUE : Vue du dessous REMARQUE : Vue du dessous 16 16 17 17 17 17 18 17255 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Guide d’installation 8 Fixez les assemblages de l’étagère latérale inférieure en plaçant le crochet du support de l’étagère sur la barre plate de l’assemblage du panneau latéral. La zone du crochet s’insérera entre la feuille de plastique latérale et la barre plate en aluminium dans les tubes verticaux du plateau latéral du moule. 19. 20. 19 L’assemblage est complété! Le chariot à pâtisserie mobile est prêt à utiliser ! 17255 KELMAX 4H7120-R INSTK00513_A01_C- Maximiser l’efficacité, améliorer la performance, obtenir plus de vos employés et de votre investissement—c’est ce que vous devez faire tous les jours pour que votre entreprise réussisse mieux et soit plus rentable. Et c’est ce que SPG vous aide à réaliser par le biais de notre gamme étendue d’équipement novateur de service alimentaire. Chez SPG, notre équipement est conçu de façon ergonomique pour diminuer le temps, les mouvements et les efforts de votre personnel—tout en maximisant l’efficacité de chaque pouce de votre espace disponible. Nous utilisons les meilleurs matériaux pour le travail et la fabrication avec des tolérances strictes afin de nous assurer que notre équipement offre un rendement et une valeur durables. En tant qu’entreprise mondiale, nous fabriquons des gammes de produits d’entreposage de qualité comme ISS, Kelmax, Freestyle et bien d’autres en Amérique du Nord et dans le Pacifique. Par conséquent, nos produits sont livrés chaque jour à des entreprises du monde entier…et chaque jour nous continuons de les livrer avec la promesse d’assurer leur succès et rentabilité constants. Soyez plus. Faites-en plus. www.spgusa.com ©2016 SPG International, LLC. Non seulement nous établissons des normes élevées, mais nous les dépassons. ATTENDEZ-EN PLUS 17255 Date: Company: CUSTOMER Approved by: WIN-HOLT EQUIP. GROUP purpose with regard to the product (s) produce by this drawing. This drawing represents the interpretation by Win-Holt Equipment Group of the design requested by the customer. Win-Holt will manufacture the productin accordance with this drawing (s). The customer should check it against its own criteria. Win-Holt makes no warranty of fitness for a particular SHEET OF DWG NO PROPRIETARY EXCEPT AS OTHERWISE AGREED TO IN WRITING. THE INFORMATION AND DESIGN DISCLOSED HEREIN ARE THE PROPERTY OF WIN-HOLT EQUIPMENT CORP. AND MUST NOT BE COPIED OR DISTRIBUTED OUTSIDE WIN-HOLT EQUIPMENT EXCEPT TO AUTHORIZED PERSONS WITH A GENUINE NEED-TO-KNOW WHO BY THE USE HEREOF ACKNOWLEDGE WIN-HOLT EQUIPMENT OWNERSHIP AND AGREE TO MAINTAIN THIS INFORMATION AND DESIGN IN STRICT CONFIDENCE. FINISH DO NOT SCALE DRAWING TOLERANCES ARE: 3 PLACE DECIMAL .032 FRACTIONAL 1/16 ALL SURFACES TO BE BREAK SHARP CORNERS MATERIAL ANGULAR 2 DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED QA: SCALE CHK: 9/21/2012 SIZE REV WIN-HOLT EQUIPMENT CORP. ENGINEERING PHONE: (516) 222-0335 FAX: (516) 222-0371 TITLE ITEM: IBM #: ER#: CUSTOMER: 1 4 AA btjandra 434677 AL-1820B-2LC ALUMINUM SHEET PAN RACK, 26 IN LENGTH DWN: SHT LENGTH: SHT WIDTH: LENGTH: PARTS LIST DESCRIPTIONPART NUMBERQTYITEM CENTER SPREADER434677-00221 SPREADER434677-00342 AL-1820 SIDE200-10523 25"-RUNNER .9x1.44 ALANG2362-030203.1 GRIP RING INSERT2613-SCI223.2 UPRIGHT200-105-00113.3 5"X1-1/4" POLYU GRIP RING CASTER WITH PRECISION BEARING757GRWFDC24 5"X1-1/4" SWIVEL POLYU GRIP RING CASTER W/ PRECISION BEARING & BRAKE757GRW-BKFDC25 69 7/32" 26" 5" 5" 20 9/32" 18 3/8" 3" (TYP.) 5 5 4 4 3.3 2 1 RACK SHIPS FULLY WELDED 17264 3.1 3.2 26" Date: Company: CUSTOMER Approved by: WIN-HOLT EQUIP. GROUP it against its own criteria. Win-Holt makes no warranty of fitness for a particular purpose with regard to the product (s) produce by this drawing. This drawing represents the interpretation by Win-Holt Equipment Group of the design requested by the customer. Win-Holt will manufacture the production accordance with this drawing (s). The customer should check SHEET OF DWG NO PROPRIETARY EXCEPT AS OTHERWISE AGREED TO IN WRITING. THE INFORMATION AND DESIGN DISCLOSED HEREIN ARE THE PROPERTY OF WIN-HOLT EQUIPMENT CORP. AND MUST NOT BE COPIED OR DISTRIBUTED OUTSIDE WIN-HOLT EQUIPMENT EXCEPT TO AUTHORIZED PERSONS WITH A GENUINE NEED-TO-KNOW WHO BY THE USE HEREOF ACKNOWLEDGE WIN-HOLT EQUIPMENT OWNERSHIP AND AGREE TO MAINTAIN THIS INFORMATION AND DESIGN IN STRICT CONFIDENCE. FINISH DO NOT SCALE DRAWING TOLERANCES ARE: 3 PLACE DECIMAL .032 FRACTIONAL 1/16 ALL SURFACES TO BE BREAK SHARP CORNERS MATERIAL ANGULAR 2 DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED QA: SCALE CHK: 6/18/2020 SIZE REV WIN-HOLT EQUIPMENT CORP. ENGINEERING PHONE: (516) 222-0335 FAX: (516) 222-0371 TITLE ITEM: IBM #: ER#: CUSTOMER: 1 14 AA TGilleland 1142913_4IN AL-1308H-DW-TGDWN: SHT LENGTH: SHT WIDTH: LENGTH: 30" 18 1/2" 31 1/8" 18 1/2" 3" 13 5/8"13 5/8" 1/8"GENERAL NOTE: * WELDED ALUMINUM CONSTRUCTION * UPRIGHT: 1" SQ ALUM TUBE * MID UPRIGHT: 3/4" SQ. ALUM TUBE * RUNNER: 1"X 1.5" .070" AL ANGLE * CASTER: 4" X 1.25" SWIVEL PLATE PU/PO STAINLESS STEEL (1) WITH BRAKE * TRAY GUARD: 1/4" X 1" AL. FLAT BAR 6 3/16" 21934 GENERAL TOLERENCESIN ACCORDANCE WITHISO 2768-M 3 1 2 4 5 6 7 8 31.06 789 25.44 646 31.55 801 19.13 486 19.37 492 #3 #11 REVISIONS ZONE REV.DESCRIPTION BY DATE ECO / NPR 01 RELEASED FOR CUSTOMER APPROVAL SSI 2/12/2020 9518 ITEM NO.QTY.PART NO.DESCRIPTION DWG. NO. BILL OF MATERIALS 8 1 LU30*30" UNIVERSAL SHELF LEDGE 102709_A01 7 2 LU18*18" UNIVERSAL SHELF LEDGE 102709_A01 6 1 1836PSG 18"X36" SHELF GUARD OPAQUE 100251_P01 5 1 TF336*3-SIDED FRAME, 18"X36"102552_A01 4 1 1830FSW FSW SHELF, 18"X30"100086_A01 3 4 CM3M 3" SWIVEL RUBBER CASTER 100810_A01 2 1 1830*18"X30" ISS WIRE SHELF 101151_A01 1 4 P21N*21" ISS POST FOR CASTER (NO FOOT)100113_A02 WST1878CPart No. SHEET 1 of 1 Rev. 2/12/2020 SSI Material: TBD Drawn By: AS NOTED Finish:AS SPECIFED 01 UNDER SHELF CART KIT 18"X30" Weight: TBD 11230 Harland DriveCovington, Georgia 30014PH: 1-800-810-9080www.spgusa.com PROPRIETARY NOTICE: This sheet contains confidential, proprietary information of Storage Product Group International LLC. Any person accepting this sheet and/or information agrees to make no disclosure, use or duplication thereof except as authorized by SPG to return this sheet on request. Copyright © 2010 Storage Product Group International. All rights reserved. S:\Covington\Engineering\ENG-SW\CURRENT VERSIONS_SPG\ASSEMBLIES\ASSY_SKETCHES\ 104999_A01 WST1878C NONE Scale: TBD Sketch No. Approved By: TBD Date: Volume: 104999_S01 Description: DIMENSIONS IN ( ) ARE REFERENCE.DIMENSIONS IN [ ] ARE MILLIMETERS, ALL OTHER DIMENSIONS ARE INCHES.UNDER SHELF CART KIT 18"X30" cu ft. lbs. 22212