The URL can be used to link to this page

FIRE ALARM SUBMITTAL - Eagle Plaza 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 CEILING MOUNTED AUDIO/VISUAL SEE NOTE 2 CEILING MOUNTED HEAT/SMOKE SEE NOTE 1 6'-8" (80") CEILING MOUNTED AUDIO/VISUAL SEE NOTE 3 MAX 30'-0" (360") CEILING MOUNTED HEAT/SMOKE SEE NOTE 1 MAX 6'-0" (72") & MIN 5'-6" (66") TYP. 5'-0" (60") TYP. MAX 4'-0" (48") MIN 3'-6" (42") NOTES: 1.LOCATE CEILING MOUNTED HEAT/SMOKE DETECTORS ON THE BOTTOM OF THE DECK/SUSPENDED CEILING (NOT ON BOTTOM OF STRUCTURAL MEMBERS), AND AS INDICATED IN NFPA 72. 2.LOCATE CEILING MOUNTED NOTIFICATION DEVICES ON BOTTOM OF BEAMS OR JOISTS; WITH CLEAR LINE OF SITE IN ALL DIRECTIONS; NO GREATER THAN THIRTY (30) FEET ABOVE THE FINISHED FLOOR; AND AS INDICATED IN NFPA 72. 3.LOCATE CEILING MOUNTED NOTIFICATION DEVICES FLUSH WITH THE SUSPENDED CEILING; ALIGNED WITH LIGHTING, SPRINKLERS, AND OTHER ARCHITECTURAL FIXTURES; WITH CLEAR LINE OF SITE IN ALL DIRECTIONS; NO GREATER THAN THIRTY (30) FEET A.F.F. ; AND AS INDICATED IN NFPA 72. 4.LOCATE WALL MOUNTED NOTIFICATION DEVICES AT 80" A.F.F TO BOTTOM OF BACK BOX. 5.COORDINATE EXACT MOUNTING HEIGHT OF CONTROL PANELS, ANNUNCIATORS, AND POWER SUPPLIES WITH THE GENERAL CONTRACTOR, ELECTRICAL CONTRACTOR AND AHJ PRIOR TO INSTALLATION. 6.MEASURED TO THE OPERABLE PART OF THE PULL STATION. FAA WALL MOUNTED AUDIO/VISUAL PULL STATION FACU FAPS B2 A,B ###cd A 6,705 FT2 ANN F FIRE ALARM ANNUNCIATOR - XXcd WP 7067 EOL 77-FACPA FAPS LF BUILDING DATA ADDRESS:937 Yelm Ave W, Yelm, WA 98597 PARCEL #: AREA: TYPE OF CONST: OCCUPANCY: 45170000400 TYPE V-B B FireTek Design & Installation FIRE ALARM CONTROL UNIT - SK-6700 FIRE ALARM POWER SUPPLY - AES 24V POWER CONVERSION MODULE AES INTELLITAP DIALER FOR RADIO MANUAL PULL STATION - SK-PULL-SA SMOKE DETECTOR - SK-PHOTO-W DUCT SMOKE DETECTOR - CEILING MOUNT STROBE - SCRLED CEILING MOUNT HORN STROBE - PC2RLED WALL MOUNT STROBE - SRLED WALL MOUNT LOW FREQUENCY HORN - INDICATES RELOCATED DEVICES INDICATES WEATHER RESISTANT DEVICES INDICATES CANDELA RATING OF STROBE LIGHT DENOTES END OF CIRCUIT FOR THAT NAC LOOP 1 0 0 0 0 1 1 0 3 4 0 0 INDICATES THE CANDELA SETTING OF THE STROBE. INDICATES 1x OF THE SPECIFIED WIRE. THE LETTER CORRESPONDS TO THE WIRE TYPE, IN THE WIRE LEGEND. INDICATES 1x EACH OF THE SPECIFIED WIRE. THE LETTER CORRESPONDS TO THE WIRE TYPE, IN THE WIRE LEGEND. INDICATES 2 OF THE SPECIFIED WIRE. THE LETTER CORRESPONDS TO THE TYPE, THE EXPONENT IS THE QUANTITY OF THAT WIRE. DESCRIPTION WIRE LEGEND SYMBOLS SEE NOTE 6 SEE NOTE 5 SEE NOTE 4 SUSPENDED CEILING SEE NOTE 5 FINISHED FLOOR TYPICAL DEVICE MOUNTING HEIGHT CEILING/DECK SYMBOL LEGEND RUNNER SERVICE PROVIDED BY MONITORING SERVICE PROVIDED BY: FireTek Design & Installation M C T MONITOR MODULE - CONTROL MODULE - IDP-CONTROL SPRINKLER TAMPER CONNECTION 0 0 HEAT DETECTOR -0 0 THE PURPOSE OF THIS DESIGN IS TO PROVIDE OCCUPANT NOTIFICATION UPON THE ACTIVATION OF THE DETECTION DEVICES. THE SCOPE OF THIS PROJECT IS EXTENDING THE EXISTING AUTOMATIC FIRE ALARM SYSTEM TO 2 NEW PORTABLES. AMBIENT SOUND PRESSURE LEVELS ARE SPECIFIED IN TABLE A.18.3.2 FROM NFPA 72 2013 HANDBOOK. ANTICIPATED AUDIBILITY IS FIGURED BY THE "6DB RULE OF THUMB" METHOD REFERENCED IN NFPA 72 2013 HANDBOOK. DESIGN NARRATIVE SHEET INDEX SHEET NUMBER DISCRIPTION FA01 PROJECT DETAILS FA02 FIRE ALARM DEVICE AND WIRE LAYOUT WIRE USE WIRE LEGEND TYPE DESCRIPTION C SBUS CIRCUIT 18 GAUGE 4 CONDUCTOR - FPLP DATA CIRCUIT TO ANNUNCIATOR A SLC CIRCUIT 18 GAUGE 2 CONDUCTOR - FPLP DATA CIRCUIT TO SMOKE/HEAT DETECTORS, AND PULL STATIONS 500 Cherry St SE Olympia, WA 98501 (360)353-3157 500 Cherry St SE Olympia, WA 98501 (360)353-3157 FACP D NAC CIRCUIT 14 GAUGE 2 CONDUCTOR - FPLP NOTIFICATION CIRCUIT TO STROBES/HORN STROBES NAC CIRCUIT 14 GAUGE 2 CONDUCTOR - FPLP NOTIFICATION CIRCUIT TO STROBES/HORN STROBES B RELO 0 1 1WALL MOUNT WEATHER RESISTANT HORN STROBE - P2RK(WP) H W SPRINKLER WATERFLOW CONNECTION 0 ATTIC HEAT DETECTOR - 0 0WALL MOUNT HORN STROBE - E NAC CIRCUIT 14 GAUGE 2 CONDUCTOR - FPLP NOTIFICATION CIRCUIT TO STROBES/HORN STROBES F NAC CIRCUIT 14 GAUGE 2 CONDUCTOR - FPLP NOTIFICATION CIRCUIT TO STROBES/HORN STROBES FUNCTION 4 KEY FUNCTION 3 KEY FUNCTION 2 KEY FUNCTION 1 KEY DRILL BUTTON AC / BATTERY NOTIFICATION CIRCUIT DEVICE OR MODULE SYSTEM COMPONENT HVAC SUPERVISORY CONDITIONS SPRINKER SUPERVISORY SWITCHES PULLSTATION SMOKE DETECTOR WATERFLOW SWITCH AL A R M L E D A C T I V A T E S SU P E R V I S O R Y L E D A C T I V A T E S TR O U B L E L E D A C T I V A T E S PI E Z O A C T I V A T E S AL A R M W I T H P O I N T I D T R A N S M I T T E D SU P . W I T H P O I N T I D T R A N S M I T T E D TR O U B L E W I T H P O I N T I D T R A N S M I T T E D GE N E R A L A L A R M N O T I F I C A T I O N EX T E R I O R S T R O B E O N L Y WA T E R F L O W B E L L HV A C S H U T D O W N FI R E D A M P E R S C L O S E INPUT DEVICES OR ACTIONS (TYP) OU T P U T D E V I C E S O R A C T I O N S (T Y P ) ALARM INITIATING DEVICES FACP DISPLAY / KEYPAD AU X I L I A R Y C O N T R O L S NO T I F I C A T I O N C I R C U I T S AE S C O M M U N I C A T O R FA C P F A R A P D I S P L A Y SUPERVISORY INITIATING DEVICES TROUBLE CONDITIONS FA01 Sheet Number Pr o j e c t N a m e : Da t e : Dr a w n B y : Em a i l : Jo b # : Fi l e N a m e : DW G N a m e : Pl o t D a t e : Ve r s i o n : Re v : Da t e : De s c r i p t i o n : BM I BR A Y D E N @ F I R E T E K O L Y M P I A . C O M Au t o C A D L T 2 0 2 4 FA _ E a g l e P l a z a 10 / 0 2 / 2 0 2 4 Ea g l e P l a z a 93 7 Y e l m A v e W Ye l m , W A 9 8 5 9 7 FA - E a g l e P l a z a 10 / 0 2 / 2 0 2 4 xx x x x x CAFE WORKROOM RESTROOM VEST. RESTROOM 1 RESTROOM 2 ENGINE DRIVE-THRU FACP EOL F 15cd 15cd 30cd 75cd 30cd 177cd 177cd M98:S001 M98:M001 A A C C C C C2C C C C2 177cd WP M Install 5 SK-MONITOR Modules for connection to the sprinkler system. Address points M98:M002 - M98:M006 A FA02 Sheet Number Pr o j e c t N a m e : Da t e : Dr a w n B y : Em a i l : Jo b # : Fi l e N a m e : DW G N a m e : Pl o t D a t e : Ve r s i o n : Re v : Da t e : De s c r i p t i o n : Au t o C A D L T 2 0 2 4 BM I BR A Y D E N @ F I R E T E K O L Y M P I A . C O M Fire Alarm Device and Wiring Layout 0 2'4'8' SCALE: 1/8"=1'-0"(IN FEET) FA _ E a g l e P l a z a 10 / 0 2 / 2 0 2 4 Ea g l e P l a z a 93 7 Y e l m A v e W Ye l m , W A 9 8 5 9 7 FA - E a g l e P l a z a 10 / 0 2 / 2 0 2 4 xx x x x x 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 EaglePLaaa - Battery Calculation Report PANEL INFORMATION Panel Type 6700SK No. of Loops 1 No. of Devices 7 Status -) PASS =RY & CHARGER REQUIREMENT formal Operation 24 Hours BAT-1270 7Ah 5.043Ah 13B-17 In Alarm 5 Mins Suggested Battery Suggested Capacity Required Capacity Suggested Batt. Box Standby/Quiescent Load Alarm Load Standby Load Current x Panel in Normal operation (In hours) In Alarm Load Current(InAmps) x Panel In Alarm(In Hours) 0.167 24 = 4.008 Ah D.313 0.083(5mins) = 0.026Ah Total Current Load - 4.034Ah MuIt! pLywith derating factor- x1.25 Adding with spare capacity - N/A TataLAH required - 5.043Ah LOOP1 DETAILS Number of devices — Z-7mAconsumed 2-7% 0% 100 J, PANEL MODULES & CIRCUITS 310 mA Consumed 0-91W No. of Modules & 1 Circuits C?i, 1001L 6700 SK Control Panel I 165 310 Loop Details Loopi D- �Quantlty SK-PHOTO-W -(IV) 1 0.20 0.45 5K-MONITOR 5 1.88 1.08 SK-PULL-SA 1 0.38 0.38 NAC CIRCUITS EaglePLaza - Voltage Drop CaLculation Report POWERSOURCE Power 6700CLASS B I Brand SilentKnight IModel 6700CLASS B I Nc)r anal 20.4VOLTS Source Number Voltage CIRCUIT 1- POINT TO P01NT NAC Circuitl I 0.78 AMPS I CLASS 8 I 14 AWG I 8 Devices I 0.76 AMPS USED I 0.43 VOLTAGE DROP # I Device Model I Candela Pattern Volume Tone CURRENT(AMPS) I Dist from prey device (feet) Volts 1 PC2RLED 185 Temporal High Electromechanical 0.19 30 20.25 2 PC2RLED 185 Temporal }sigh Electromechanical 0.19 30 20.14 3 P2RK 115 Temporal High Electromechanical 0.218 30 20.07 4 PC2RLED 30 Temporal High Electromechanical 0.038 40 20.02 5 SCRLED 75 0.07 35 19.99 6 PC2RLED 30 Temporal High Electromechanical 0.038 35 19.97 7 SCRLED 15 0.018 10 19.97 8 SCRLED 15 0.018 15 19.97 CIRCUIT 2 - POINT TO POINT NAC Circuitl I OAMPS I CLASS B I 14AWG I 0 Devices 10 AMPS USED I OVOLTAGE DROP # I Device Model Candela Pattern Volume Tone CURRENT CAMPS} Dist from prev device (feet) Volts 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 • Capable of providing up to 100 points to satisfy smaller installation needs • Connect up to 17 panels on one site with convenient single- point access using the SK-NIC Network Interface Card. Connected panels can have mixed compatible FACP models • Convenient field-upgradeable firmware •#VJMUJOEVBMQBUI 1054BOE*1 DPNNVOJDBUJPOT XJUIPQUJPOBMDFMMVMBS NPEFMTBWBJMBCMFGPS SFMJBCMFCBDLVQ SFQPSUJOH • 6860 annunciator with a 4 x 40 large display • 'PVSVTFS QSPHSBNNBCMFCVUUPOT NJOJNJ[FUJNFTQFOU FYFDVUJOHDPNQMFYPS SPVUJOFUBTLT • Built-in USB interface for convenient and quick programming • Programmable date setting for automatic and convenient Daylight Saving Time changes •+VNQ4UBSUkBVUP QSPHSBNNJOHSFEVDFT JOTUBMMBUJPOUJNF • 125 software zones and 125 output groups for flexible design options 6700 "EESFTTBCMF'JSF"MBSN$POUSPM1BOFM The 6700 is an addressable fire alarm control panel (FACP) UIBUJTB EJSFDUSFQMBDNFOUGPSUIF'"$15IF can be configured to BDIJFWFBQPJOUDBQBDJUZPGVQUPQPJOUT*UIBTPOFCVJMUJO TJHOBMJOHMJOFDJSDVJU 4-$ XIJDIDBOTVQQPSU4ZTUFN4FOTPSk 4, TFOTPSTBOE4,NPEVMFTPS)PDIJLJk 4% EFWJDFT "DPNNPODPNNVOJDBUJPOTBOEBOOVODJBUJPOMJOLBMMPXTVQUP panels to be connected via copper or fiber optic cable. A designated panel is configured as the communicator for all panels in the link for DPOWFOJFOUTJOHMFQPJOUDPNNVOJDBUJPOT5IFBMTPIBTBCVJMUJO EVBMMJOF1054BOE*1DPNNVOJDBUPSXJUIBEEJUJPOBMDFMMVMBSPQUJPOT BWBJMBCMF 5IFTZTUFNDBOCFFOIBODFECZBEEJOHNPEVMFTTVDIBTUIF SFNPUFBOOVODJBUPSXIJDIBMTPIBTGPVSQSPHSBNNBCMFGVODUJPO CVUUPOTUPIFMQBVUPNBUFUBTLTBOESFEVDFUJNFTQFOUBUUIFQBOFM 48*'5kXJSFMFTTDPNQBUJCJMJUZQSPWJEFTPQUJPOTGPSXJSFMFTTEFUFDUJPO UISPVHIB$MBTT"NFTIOFUXPSL*UJTJEFBMGPSIBSEUPXJSFMPDBUJPOT CVJMEJOHTXIFSFOFXXJSJOHJTOPUBMMPXFE PSUPQSPWJEFBOFBTZJOTUBMM fi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• General Alarm (Red)'MBTIFTJGJO BMBSNTPMJEXIFOBMBSNJTTJMFODFE • Supervisory (Yellow):'MBTIFTJGB TVQFSWJTPSZDPOEJUJPOFYJTUTTPMJE XIFOTVQFSWJTPSZJTTJMFODFE • System Trouble (Yellow)'MBTIFT JGBUSPVCMFDPOEJUJPOFYJTUT TPMJEXIFOUSPVCMFJTTJMFODFE • System Silenced (Yellow) 0OXIFOBOBMBSN USPVCMFPS TVQFSWJTPSZDPOEJUJPOIBTCFFO TJMFODFECVUOPUZFUDMFBSFE • System Power (Green): 'MBTIFT GPS"$GBJMVSFTPMJEXIFO QPXFSTZTUFNTBSFOPSNBM USER INTERFACE 5IFCVJMUJOYBOOVODJBUPS XJUIDIBSBDUFS-$%EJTQMBZ BOEMBSHFFBTZUPVTFUBDUJMF UPVDIQBEDBOCFVTFEGPSTZTUFN PQFSBUJPO QSPHSBNNJOHBOE NBJOUFOBODF*UIBs fiWF-&%TGPS BMBSN TVQFSWJTPSZ TZTUFNUSPVCMF TZTUFNTJMFODFEBOETZTUFNQPXFS 4ZTUFNPQFSBUJPOTJODMVEFTJMFODJOH BMBSNTBOEUSPVCMFT SFTFUUJOHBMBSNT BOEUIFEJTQMBZPGBMBSNUSPVCMFTBOE NFNPSZ5IFTZTUFNTOPOWPMBUJMF FWFOUIJTUPSZCVGGFSTUPSFT FWFOUTGPSWJFXJOHGSPNUIFCVJMU JOPSSFNPUFBOOVODJBUPS4ZTUFN PQFSBUJPOTDBOCFJOJUJBUFEXJUIB NFDIBOJDBl fiSFfiHIUFSTLFZPSB WBMJEUPEJHJUPQFSBUPSTDPEF PROGRAMMING 5IFTZTUFNPGGFSTTFWFSBMPQUJPOT UPTJNQMJGZBOETQFFEVQQSPHSBNNJOH +VNQ4UBSUkBVUPQSPHSBNNJOH NJOJNJ[FTQSPHSBNNJOHSFRVJSFEUP TUBSUBOFXTZTUFN5IFCVJMUJOLFZQBE PSUIF PSSFNPUF BOOVODJBUPSTHJWFZPVPOTJUFBDDFTTUP DVSSFOUTZTUFNQSPHSBNNJOH 1SPHSBNNJOHDBOBMTPCFBDDPNQMJTIFE VTJOHUIF8JOEPXTkCBTFE)POFZXFMM 'JSF4PGUXBSF4VJUF )'44 QSPHSBN SOFTWARE TOOLS SKST:4JMFOU,OJHIU4FMFDUJPO5PPM QSPWJEFTUIFJOTUBMMFSPSEFTJHOBSDIJUFDU XJUIB8JOEPXTkTPGUXBSFTZTUFN DPOGJHVSBUJPOUPPMUPDSFBUFBEFUBJMFE #JMMPG.BUFSJBM #0. BOECBUUFSZ DBMDVMBUJPOT HFSS:)POFZXFMM'JSF4PGUXBSF4VJUF QSPWJEFTDPNNVOJDBUJPOBOEQBOFM QSPHSBNNJOH EFUFDUPSTUBUVT FWFOU IJTUPSZBOEBEEJUJPOBMEBUB3FRVJSFTB 1$SVOOJOH.JDSPTPGUk8JOEPXTk ADDITIONAL INFORMATION 5XJTUFEVOTIJFMEFEQBJSXJSFJT SFDPNNFOEFE5IFBMTPIBT QSFTFUOPUJGJDBUJPODBEFODFQBUUFSOT JODMVEJOH"/4* • UL Listed:4 • CSFM • FDNY$0" ORDERING INFORMATION "EESFTTBCMF'JSF"MBSN $POUSPM1BOFM 3FEDBCJOFU COMPATIBLE ANNUNCIATORS 6860:Y-$%SFNPUe fiSF BOOVODJBUPS MJOFTBOEVQUP DIBSBDUFST QFSTZTUFNGPVS QSPHSBNNBCMFCVUUPOT 5860:Y-$%SFNPUe fiSF BOOVODJBUPSJTHSBZ3JTSFE 6855:Y-$%SFNPUe fiSF BOOVODJBUPS 5865-3 or 5865-4:-&%BOOVODJBUPST DBOEJTQMBZVQUP-&%T SFEBOE ZFMMPX 5IFIBTLFZTXJUDIFT GPSTJMFODFBOESFTFU BOEBTZTUFN USPVCMF-&% 5880:5IF-&%*0NPEVMF IBTQSPHSBNNBCMF-&%PVUQVUT BOEFJHIUTVQFSWJTFEESZDPOUBDU JOQVUTXIJDIBSFVTFGVMGPSDVTUPN BQQMJDBUJPOT:PVDBOVTFVQUPFJHIU NPEVMFTPOPOFDPOUSPMQBOFMGPS NBYJNVm fl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mportant: :PV DBOOPU NJY 4, BOE 4% EFWJDFTJOUIFTBNFGJSFBMBSNTZTUFN Page 2 of 4 — 351607:B 9/26/2018 4,$0.1"5*#-&"%%3&44"#-& DEVICES SK-ACCLIMATE:.VMUJDSJUFSJB QIPUPFMFDUSJDTNPLFEFUFDUPSXJUIUIFSNBM m'GJYFEUFNQFSBUVSF SK-BEAM:3FGMFDUFECFBNTNPLFEFUFDUPS XJUIPVUUFTUGFBUVSF SK-BEAM-T:3FGMFDUFECFBNTNPLF EFUFDUPSXJUIUFTUGFBUVSF SK-CONTROL:4VQFSWJTFEDPOUSPMNPEVMF SK-CONTROL-6:4JYDJSDVJUTVQFSWJTFE DPOUSPMNPEVMF SK-DUCT:1IPUPFMFDUSJDEVDUTNPLF EFUFDUPSXJUIFYUFOEFEBJSTQFFESBOHF SK-FIRE-CO:'PVSDSJUFSJBGJSFBOEDBSCPO NPOPYJEFEFUFDUPS SK-HEAT:'JYFEUIFSNBMEFUFDUPS m' 4,)&"58'JYFEUIFSNBMEFUFDUPS m' XIJUF SK-HEAT-ROR:'JYFESBUFPGSJTFEFUFDUPS m' 4,)&"53038'JYFESBUFPGSJTFEFUFDUPS m' XIJUF SK-HEAT-HT:'JYFEIJHIUFNQFSBUVSF UIFSNBMEFUFDUPS m' 4,)&"5)58'JYFEIJHIUFNQFSBUVSF UIFSNBMEFUFDUPS m' XIJUF SK-ISO:'BVMUJTPMBUPSNPEVMF SK-MINIMON:.JOJNPOJUPSNPEVMF SK-MONITOR:.POJUPSNPEVMF SK-MONITOR-2:%VBMJOQVUNPOJUPS NPEVMF SK-MON-10:JOQVUNPOJUPSNPEVMF SK-PHOTO:1IPUPFMFDUSJDTNPLFEFUFDUPS 4,1)05081IPUPFMFDUSJDTNPLF EFUFDUPS XIJUF SK-PHOTO-T:1IPUPFMFDUSJDTNPLFEFUFDUPS XJUIUIFSNBM m'GJYFEUFNQFSBUVSF 4,1)050581IPUPFMFDUSJDTNPLF EFUFDUPSXJUIUIFSNBM m'GJYFE UFNQFSBUVSF XIJUF SK-PHOTOR:1IPUPFMFDUSJDEFUFDUPSXJUI SFNPUFUFTUDBQBCJMJUZ 4,1)050381IPUPFMFDUSJDEFUFDUPS XJUISFNPUFUFTUDBQBCJMJUZ XIJUF SK-PULL-SA:"EESFTTBCMFTJOHMFBDUJPO QVMMTUBUJPO SK-PULL-DA:"EESFTTBCMFEVBMBDUJPOQVMM TUBUJPO SK-RELAY:"EESFTTBCMFSFMBZNPEVMF SK-RELAY-6:"EESFTTBCMF4JYSFMBZDPOUSPM NPEVMF SK-RELAYMON-2:"EESFTTBCMF%VBMSFMBZ NPOJUPSNPEVMF SK-ZONE:"EESFTTBCMF[POFJOUFSGBDF NPEVMF SK-ZONE-6:4JY[POFJOUFSGBDFNPEVMF # *7 CBTFGPS4,84FSJFT B210LP:NPVOUJOHCBTF # #- *7 8)*5& GMBOHFMFTTCBTF B501:'MBOHFMFTTNPVOUJOHCBTF #4 *7 8) *OUFMMJHFOUTPVOEFSCBTF B200S:*OUFMMJHFOUTPVOEFSCBTF #4-' *7 8) -PX'SFRVFODZ JOUFMMJHFOUTPVOEFSCBTF B200S-LF:-PXGSFRVFODZJOUFMMJHFOU TPVOEFSCBTF #3# *7 8) 3FMBZCBTF B224RB:3FMBZCBTF ##* *7 8) *TPMBUPSCBTF B224BI:*TPMBUPSCBTF SD COMPATIBLE ADDRESSABLE DEVICES SD505-6AB:"EESFTTBCMFCBTF SD505-6IB:"EESFTTBCMFTIPSUDJSDVJU JTPMBUPSCBTF SD505-6RB:"EESFTTBCMFSFMBZCBTF SD505-6SB:"EESFTTBCMFTPVOEFSCBTF SD500-AIM:"EESFTTBCMFJOQVUNPEVMF TXJUDIJOQVU SD500-ANM:"EESFTTBCMFOPtifiDBUJPO NPEVMF SD500-ARM: "EESFTTBCMF SFMBZ NPEVMF SD505-DTS-K: 3FNPUF UFTU TXJUDI BOE-&%JOEJDBUPSGPSUIF4%%6$53 SD505-DUCT:"EESFTTBCMF%VDU4NPLF %FUFDUPS SD505-DUCTR:"EESFTTBCMF%VDU %FUFDUPSIPVTJOHXJUISFMBZCBTF SD505-HEAT:"CTPMVUFUFNQFSBUVSFIFBU EFUFDUPS5SJQQPJOUSBOHFGSPN m'ŗm' m$ŗm$ SD500-LIM:"EESFTTBCMF-JOFJTPMBUPS NPEVMF SD500-MIM:"EESFTTBCMF.JOJJOQVU NPOJUPSNPEVMF TXJUDIJOQVU SD505-PHOTO:1IPUPFMFDUSJDTNPLF EFUFDUPS SD500-PS/-PSDA:"EESFTTBCMF4JOHMFPS EVBMBDUJPOQVMMTUBUJPO SD500-SDM:"EESFTTBCMFTNPLFEFUFDUPS NPEVMF AUDIBLE/VISIBLE DEVICES 5IFTF"7EFWJDFTBSFBMMXJSF$PMPSş3Š JOEJDBUFTSFEş8ŠEFOPUFTXIJUF'PSB DPNQMFUFMJTUJOHPG4JMFOU,OJHIU"7EFWJDFT HPUPXXXTJMFOULOJHIUDPN CHSRL/CHSWL:8BMMDIJNFTUSPCF CHSCRL/CHSCWL:$FJMJOHDIJNFTUSPCF CHRL/CHWL:8BMMDIJNF HRL/HWL:8BMMIPSO P2RL/P2WL:8BMMIPSOTUSPCF PC2RL/PC2WL:$FJMJOHIPSOTUSPCF SRL/SWL:8BMMTUSPCF SCRL/SCWL:$FJMJOHTUSPCF SPSCRL/SPSCWL:$FJMJOHTQFBLFSTUSPCF SPSRL/SPSWL:8BMMTQFBLFSTUSPCF SPRL/SPWL:8BMMTQFBLFS SPCRL/SPCWL:$FJMJOHTQFBLFS SWIFT WIRELESS DEVICES SWIFT is only compatible with System Sensor (SK) devices. It is not compatible with Hochiki (SD) devices. 84,8(*8JSFMFTT(BUFXBZ 84,1)0508JSFMFTT1IPUPFMFDUSJD TNPLFEFUFDUPS WSK-PHOTO-T:8JSFMFTT.VMUJDSJUFSJB QIPUPFMFDUSJDTNPLFEFUFDUPSXJUIUIFSNBM EFUFDUJPO m'GJYFEUFNQFSBUVSF BOE #8CBTF WSK-HEAT:8JSFMFTT)FBU m'GJYFE UFNQFSBUVSF BOE#8CBTF WSK-HEAT-ROR:8JSFMFTTIFBU 303 m'GJYFEUFNQFSBUVSF BOE#8 CBTF WSK-MONITOR:8JSFMFTTNPOJUPSNPEVMF WSK-RELAY:8JSFMFTTSFMBZNPEVMF W-USB:48*'55PPMT64#USBOTDFJWFSVTFE GPSDPNNVOJDBUJPOXJUI48*'5EFWJDFT SBUS ACCESSORIES 5496:"BNQOPUJGJDBUJPOQPXFSFYQBOEFS XJUIGPVSQPXFSMJNJUFEOPUJGJDBUJPO BQQMJBODFDJSDVJUPVUQVUT 5883:3FMBZJOUFSGBDF1SPWJEFT'PSN$ SFMBZT 5824:4FSJBM1BSBMMFMQSJOUFSJOUFSGBDF NPEVMFGPSQSJOUFSDPOOFDUJPO 5895XL:1PXFSTVQQMZXJUITJY'MFYQVUk DJSDVJUT BOEUXP'PSN$SFMBZT.BYQFS TZTUFN 5815RMK:3FNPUFNPVOUJOHLJU %JNFOTJPOTŠ8YŠ)YŠ% COMMUNICATION OPTIONS CELL-CAB-SK:$FMMVMBSDPNNVOJDBUPS NFUBMFODMPTVSFXJUIMPDLLFZ CELL-MOD:$FMMVMBSDPNNVOJDBUPS QMBTUJD FODMPTVSF 4PMFQBUI QPXFSFECZQBOFM IPGSM-4G:%VBMQBUIGJSFBMBSN DPNNVOJDBUPS DFMMVMBSBOEPS*1 QSJNBSZPS CBDLVQ TFMFDUBCMF SK-IP-2:3FNPUFSFQPSUJOHWJBUIF*OUFSOFU 3FRVJSFTB7JTPS"MBSNkSFDFJWFSBUUIFDFOUSBM TUBUJPO MISC. ACCESSORIES SK-NIC:/FUXPSL*OUFSGBDF$BSE1SPWJEFTB DPNNPODPNNVOJDBUJPOTMJOLGPSUIF SK-NIC-KIT:*OTUBMMBUJPO"DDFTTPSZ,JU SK-FML:'JCFS0QUJD.VMUJ.PEF USBOTNJUUFS BOESFDFJWFS SK-FSL:'JCFS0QUJD4JOHMF.PEF RBB:3FNPUFCBUUFSZCPYBDDFTTPSZDBCJOFU GPSCBUUFSJFTUIBUBSFUPPMBSHFUPGJUJOUIF '"$1DBCJOFU%JNFOTJPOTŠ8YŠ)Y Š% NN8YNN)YNN% SK-SCK: 4FJTNJD $PNQMJBODF ,JU VTFE UP TFDVSFMZGBTUFOCBUUFSJFTUPUIFGJSFQBOFM 1BHFPGŘ# 'MFYQVUk )POFZXFMMk +VNQ4UBSUk 4JMFOU,OJHIUk 48*'5k BOE4ZTUFN 4FOTPSkBSFSFHJTUFSFE USBEFNBSLTPG)POFZXFMM *OUFSOBUJPOBM*OD )PDIJLJkJTBSFHJTUFSFE USBEFNBSLPG)PDIJLJ $PSQPSBUJPO.JDSPTPGUk BOE8JOEPXTkBSF SFHJTUFSFEUSBEFNBSLTPG .JDSPTPGU$PSQPSBUJPO 5IJTEPDVNFOUJTOPU JOUFOEFEUPCFVTFEGPS JOTUBMMBUJPOQVSQPTFT8F USZUPLFFQPVSQSPEVDU JOGPSNBUJPOVQUP EBUFBOEBDDVSBUF8F DBOOPUDPWFSBMMTQFDJGJD BQQMJDBUJPOTPSBOUJDJQBUF BMMSFRVJSFNFOUT"MM TQFDJGJDBUJPOTBSFTVCKFDU UPDIBOHFXJUIPVUOPUJDF 'PS5FDIOJDBM4VQQPSU DBMM 5FDIOJDBM4QFDJGJDBUJPOT PHYSICAL Overall Dimensions:Š8YŠ)YŠ% Weight:MCT Color:3FE ENVIRONMENTAL Operating Temperature:m'UPm' m$UP m$ Humidity:UPSFMBUJWFIVNJEJUZ OPO DPOEFOTJOH ELECTRICAL 6700 Primary AC:7"$!)[ "5PUBM "DDFTTPSZ-PBE"!7%$QPXFSMJNJUFE Standby Current:N" Alarm Current:N" Battery Charging Capacity:UP") Battery Size:")NBYBMMPXFEJODPOUSPMQBOFM DBCJOFU-BSHFSDBQBDJUZCBUUFSJFTDBOCFIPVTFEJO 3##BDDFTTPSZDBCJOFU ]#] g)POFZXFMM*OUFSOBUJPOBM*OD Honeywell Silent Knight $MJOUPOWJMMF3PBE /PSUIGPSE $5 XXXTJMFOULOJHIUDPN NOTIFICATION APPLIANCE CIRCUITS (NACS) Two programmable circuits which can be programmed individually as: NACs:"!7%$QFSDJSDVJU QPXFSMJNJUFE XJUIBQBOFMNBYJNVNDVSSFOUPG" Auxiliary Power Circuits:"!7%$QFS DJSDVJU QPXFSMJNJUFE 4VQQPSUT$MBTT# 4UZMF BOE$MBTT" 4UZMFPS DPOfiHVSBUJPOGPSUIF4-$ WIRING:4FFUIFQSPEVDUNBOVBMGPSXJSJOHEFUBJMT 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 SK-PHOTO-W SERIES Addressable Photoelectric Smoke Detectors The Silent Knight® SK-PHOTO-W Series feature a modern design and expanded color options support a variety of contemporary aesthetic demands. In addition, each detector is constructed for exceptional installation and maintenance efficiency. The SK-PHOTO-W Series intelligent plug-in smoke detectors are designed for both performance and aesthetics, and are direct replacements for the SK-PHOTO Series detectors. A new modern, sleek, contemporary design and enhanced optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources in accordance with more stringent code standards. The SK-PHOTO-W Series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. Dual electronic thermistors add 135°F (57°C) fixed temperature thermal sensing on the SK-PHOTO-T-W. The SK-PHOTO-R-W is a remote test capable detector for use with DNR Series duct detector housings. FEATURES AND BENEFITS • Designed to meet UL 268 7th Edition • Sleek and stylish contemporary design • Stable communication technique with noise immunity • Addressable by device • Rotary, decimal addressing (Refer to the Silent Knight panel manuals for device capacity) • Two-wire SLC connection • LEDs blink every time the unit is polled • 360°-field viewing angle of the visual alarm indicators (two bi-color LEDs); LEDs blink green in Normal condition and turn on steady red in Alarm • Integral communications and built-in device-type identification • Remote test feature from the panel • Built-in functional test switch activated by external magnet • Walk test with address d351634isplay (an address of 121 will blink the detector LED 12-(pause)-1) • Low standby current • Built-in tamper-resistant feature • Designed for direct-surface or electrical- box mounting • Sealed against back pressure • Plugs into separate base for ease of installation and maintenance • Expanded color options • SEMS screws for wiring of the separate base • Optional remote, single-gang LED accessory • Optional sounder, relay, and isolator bases Page 2 of 3 — 351634:C • 5/28/2020 INSTALLATION The SK-PHOTO-W Series plug-in intelligent thermal detectors use a separate base to simplify installation, service, and maintenance. Installation instructions are shipped with each detector. Mount base (all base types) on an electrical backbox which is at least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes, see SK-61045. Note: Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring “T-taps” or branches are permitted for Class “B” wiring. Note: When using relay or sounder bases, consult the SK-ISO installation sheet I56-3627 for device limitations between isolator modules and isolator bases. OPERATION Each SK-PHOTO-W Series detector uses one of the panel’s addresses (total limit is panel dependent) on the Signaling Line Circuit (SLC). It responds to regular polls from the control panel and reports its type and the status. If it receives a test command from the panel (or a local magnet test), it stimulates its electronics and reports an alarm. It blinks its LEDs when polled and turns the LEDs on when commanded by the panel. The SK-PHOTO-W Series offers features and performance that represent the latest in smoke detector technology. PRODUCT LINE INFORMATION Note: “-IV” suffix indicates ivory color. SK-PHOTO-W: White, low-profile photoelectric sensor SK-PHOTO-T-W: White, same as SK-PHOTO-W but includes a built-in 135°F (57°C) fixed-temperature thermal device SK-PHOTO-R-W: White, low-profile intelligent photoelectric sensor, remote test capable, for use with DNR/DNRW B300-6: White, standard flanged low-profile mounting base B300-6-BP: Bulk pack of B300-6, package contains 10 B300-6-IV: Ivory, standard flanged low-profile mounting base B501-WHITE: White, standard European flangeless mounting base B501-BL: Black, standard European flangeless mounting base B501-IV: Ivory, standard European flangeless mounting base B501-WHITE-BP: Bulk pack of B501-WHITE, contains 10 B200S-WH: White, Intelligent, programmable sounder base B200S-IV: Ivory, Intelligent, programmable sounder base B200SR-WH: White, Intelligent sounder base for retrofit applications B200SR-IV: Ivory, Intelligent sounder base for retrofit applications B200S-LF-WH: White, Low Frequency Intelligent, programmable sounder base B200S-LF-IV: Ivory, Low Frequency Intelligent, programmable sounder base B200SR-LF-WH: White, Low Frequency Intelligent sounder base for retrofit applications B200SR-LF-IV: Ivory, Low Frequency Intelligent sounder base for retrofit applications B224RB-WH: White, plug-in System Sensor® relay base B224RB-IV: Ivory, plug-in System Sensor relay base B224BI-WH: White, plug-in System Sensor isolator detector base B224BI-IV: Ivory, plug-in System Sensor isolator detector base ACCESSORIES TR300: White, replacement flange for B210LP or B300-6 bases TR300-IV: Ivory, replacement flange for B210LP or B300-6 bases RA100Z(A): Remote 3 – 32 VDC LED annunciator, mounts to a U.S. single-gang electrical box, for use with B501 and B300-6 bases only M02-04-00: Test magnet M02-09-00: Test magnet with telescoping handle CK300: White, detector color kit, pack of 10 CK300-IV: Ivory, detector color kit, pack of 10 CK300-BL: Black, detector color kit, pack of 10 SK-PHOTO-W SERIES TECHNICAL SPECIFICATIONS 351634 | C | 05/20 ©2020 Honeywell International Inc. Honeywell Silent Knight 12 Clintonville Road Northford, CT 06472-1610 203.484.7161 www.silentknight.com Silent Knight® and System Sensor® are registered trademarks of Honeywell International, Inc. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. Country of origin: Mexico PHYSICAL/ENVIRONMENTAL Sensitivity: -UL Applications: 0.5% to 4.0% per foot obscuration. -ULC Applications: 0.5% to 3.5% per foot obscuration Size: 2.0" (51mm) high; base determines diameter -B300-6: 6.1" (15.6 cm) diameter -B501: 4" (10.2 cm) diameter For a complete list of detector bases, see SK-61045. Shipping weight: 3.4 oz. (95 g) Operating temperature range: • SK-PHOTO-W: 32°F to 122°F (0°C to 50°C) • SK-PHOTO-T-W: 32°F to 100°F(0°C to 38°C) • SK-PHOTO-R-W installed in a DNR/DNRW: -4°F to 158°F (-20°C to 70°C) UL/ULC Listed Velocity Range: 0-4000 ft/ min. (1219.2 m/min.), suitable for installation in ducts Relative humidity: 10% – 93% non- condensing Thermal ratings: fixed-temperature set point 135°F (57°C), rate-of-rise detection 15°F (8.3°C) per minute, high temperature heat 190°F (88°C) ELECTRICAL SPECIFICATIONS Voltage range: 15 - 32 volts DC peak Standby current (max. avg.): 200µA @ 24 VDC (one communication every 5 seconds with LED enabled) Max current: 4.5 mA @ 24 VDC (“ON”) DETECTOR SPACING AND APPLICATIONS Silent Knight recommends spacing detectors in compliance with NFPA 72. In low airflow applications with smooth ceiling, space detectors 30 feet (9.1m). For specific information regarding detector spacing, placement, and special applications refer to NFPA 72. A System Smoke Detector Application Guide, document SPAG91, available at www.systemsensor.com. AGENCY LISTINGS AND APPROVALS These listings and approvals apply to the modules specified in this document.In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. •UL Listed: S6173 • FM Approved •CSFM: 7272-0559:0512 FEATURES & BENEFITS • Installer can open station without causing an alarm condition • Dual-color LED is visible through handle of station blinks green to indicate normal operation and remains steady red in an alarm condition • Key operated test and reset lock using lock plate actuator • Key matches compatible FACP locks • Meets ADA requirement for 5 lbs maximum pull force to active • Meets the Americans with Disabilities Act Accessibility Guidelines (ADAAG) controls and operating mechanisms guidelines (Section 4.1.3[13]) • Shell, door, and handle molded from durable LEXAN® • Reliable analog communications for trouble-free operation • Braille text on station handle • Rotary address switches for fast installation • Handle latches in down position and the word Activated appears, clearly indicating the station has been pulled • UL Listed, including UL 38, Standard of Manually Actuated Signaling System • CSFM Listed • MEA Listed SK-PULL-SA / SK-PULL-DA Intelligent Pull Stations The SK-PULL-SA is a single action pull station requiring only one motion to activate the station. The SK-PULL-DA is a dual action pull station requiring two motions to active the station. The SK-PULL-SA and SK-PULL-DA are for use with Honeywell Silent Knight Series fire control panel (FACP). Extremely easy to operate, the SK-PULL-DA and SK-PULL-SA provide a fast and practical means of manually initiating a fire alarm signal. The FACP recognizes each manual pull station by its specific address saving precious seconds in determining the location of an alarm. INSTALLATION The SK-PULL-SA and SK-PULL-DA can be surface mounted to an SB-I/O surface back box or semi-flush mounted on a standard single-gang with a minimum depth of 2.13”(5.40 cm) or double gang or 4” (10.61 cm) square electrical box. You can also use the optional (System Sensor® PN BG-TR) trim ring if the station is being semi-flush mounted. SK-PULL-SA SK-PULL-DA For a complete listing of all compliance approvals and certifications, please visit www.silentknight.com. Microsoft, Windows, and the Windows Logo are registered trademarks or trademarks of Microsoft Corporation. Silent Knight®, System Sensor® and Honeywell® are registered trademarks of Honeywell International, Inc. This document is not intended to be used for installation purposes. We try to keep our product information up-to date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For Technical Support, call 800-446-6444. SK-PULL-SA / SK-PULL-DA Technical Specifications PHYSICAL Dimensions: 5.5” H x 4" W x 1.45" D (14 x 10.2 x 3.7cm) Housing Material: LEXAN polycarbonate resin Bi-Colored LED: Blinking Green: Normal Steady Red: Alarm Switch: Single pole, single throw (SPST) normally open (N/O) switch which closes upon activation of the pull station ELECTRICAL Operating Voltage: 15 – 32VDC SLC Standby and Alarm Current: 350μ A Wire Gauge: Up to 12AWG (3.1 mm2) ENVIRONMENTAL Operating Temperature: 32ºF – 120ºF (0ºC – 49ºC) Humidity: 10% – 93% non-condensing ORDERING INFORMATION SK-Pull-SA: Single Action Pull Station SK-Pull-DA: Dual Action Pull Station ACCESSORIES BG-TR: Optional trim ring. SB-I/O: Surface backbox, indoor/outdoor. * Unless otherwise noted, specifications apply to SK-Pull-SA and SK-Pull-DA COMPATIBILITY The SK-PULL-SA AND SK-PULL-DA are compatible with the following Honeywell Silent Knight fire alarm control panels: 6820: Addressable fire alarm control panel 6820EVS: Addressable fire alarm control panel with an emergency voice system. 6808: Addressable fire alarm control panel 6700: Addressable fire alarm control panel 5700: Addressable fire alarm control panel 5808: Addressable fire alarm control panel 5820XL: Addressable fire alarm control panel 5820XL-EVS: Addressable fire alarm control panel with an emergency voice system Doc 350135 | Rev E | 11/17 © 2017 Honeywell International Inc. For more information Learn more about Honeywell Silent Knight and other products by visiting www.silentknight.com Honeywell Silent Knight 12 Clintonville Road Northford, CT 06472 800-328-0103 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 7300-1653:0525 7135-1653:0503 7135-1653:0526 Horn Strobes and Strobes: S5512, S4011 3057072 FM23FPUS0195 Horns: S4011 Agency Listings AVDS916-01 • 10/03/2023 • Page 1 Features • LED technology provides lower current draw • Digital Voltage Meter (DVM) diagnostic test points for Horn Strobes and Strobes • Common aesthetics across the L-Series platform • Standard and compact sizes • Tamper-resistant construction • Field-selectable candela settings on wall units: 15, 30, 75, 95, 110, 135, and 185 • Field-selectable candela settings on ceiling units: 15, 30, 75, 95, 115, 150, and 177 • Rotary switches for candela, tone and volume selections • Mounting plate provides plug-in design for easier installation and shorting springs to check wiring continuity • Electrically compatible with legacy SpectrAlert, SpectrAlert Advance and L-series devices • Synchronization through use of UL approved power supplies that support System Sensor Sync protocol or System Sensor MDL3 Sync Module • Horns, Strobes and Horn Strobes listed for wall or ceiling use The System Sensor L-Series and L-Series with LED platform offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry with lower current draw and modern aesthetics. LED lighting technology offers significantly lower current draw compared to older Xenon bulbs across a full candela range. This improves design flexibility for notification appliance circuits (NACs) while also reducing power supply requirements allowing for simpler and lower cost installations. Flexible design options meet virtually any application requirement: wall or ceiling mount, standard or compact sizes, red or white color choices, bezel kits for alternate markings and languages, and LED color lenses for distinctive visual signaling. In addition, installers can easily adapt devices using field selectable candela, tone and volume settings using rotary switches. The L-Series and L-Series with LED line is developed to simplify installation. All devices feature plug-in designs with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. The universal mounting plate includes an onboard shorting spring, so installers can test wiring continuity before the device is installed. In addition, the System Sensor L-Series with LED notification appliances offer a new diagnostic test point feature that allows you to measure device voltage with a digital voltage meter (DVM) without removing the appliance from the wall or ceiling. The DVM test points are discreetly located on the face of the notification appliance which enable faster troubleshooting and end of line (EOL) voltage checks while greatly reducing the risk of misplacing or damaging appliances during troubleshooting. L-Series and L-Series with LED Indoor Selectable Horns, Strobes and Horn Strobes System Sensor L-Series and L-Series with LED audible visible notification products are rich with features guaranteed to cut installation times and maximize profits with lower current draw and modern aesthetics. Horns: S4011 AVDS916-01 • 10/03/2023 • Page 2 L-Series and L-Series with LED Specifications Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage, LED Strobes and Horn Strobes Regulated 24 VDC Nominal Voltage, Horns Regulated 12 VDC or regulated 24 DC/FWR Operating Voltage Range, LED Strobes and Horn Strobes 16 to 33 V (24 V nominal) Operating Voltage Range, Horns 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG UL/ULC Maxmimum Strobe Current Draw (mA) Candela Rating 16–33 Volts Wall Ceiling Candela Range 15 18 18 30 22 22 75 70 70 95 75 75 110 85 — 115 —90 135 105 — 150 —110 177 —115 185 120 — UL/ULC Current Draw Data, Horn Tones, and Sound Output Data UL/ULC Maximum Horn Strobe Current Draw (mA) and Sound Output (dBA) Switch Pos.Sound Pattern Volume Setting Current Draw (mA RMS), Horn Strobe, Candela Range (15-185 cd) Sound Output (dBA) 16-33 Volts 16-33V 15cd 30cd 75cd 95cd 110cd WALL 115cd CEILING 135cd WALL 150cd CEILING 177cd CEILING 185cd WALL DC 1 Temporal 3 High 35 38 87 92 94 120 189 189 190 190 87 2 Temporal 3 Low 35 38 87 92 94 120 135 135 145 145 79 3 Non-Temporal High 50 52 87 92 94 120 127 127 135 135 87 4 Non-Temporal Low 35 38 87 92 94 120 125 125 130 130 79 5 3.1KHz Temporal 3 High 35 38 87 89 91 115 155 155 165 165 86 6 3.1KHz Temporal 3 Low 35 38 87 89 91 115 128 130 135 135 80 7 3.1KHz Non-Temporal High 40 42 87 89 91 115 125 125 135 135 86 8 3.1KHz Non-Temporal Low 35 38 87 89 91 115 120 120 130 130 80 UL/ULC Maxmimum Horn Current Draw (mA RMS) Sound Pattern dB 8–17.5 Volts 16–33 Volts DC DC FWR Temporal High 39 44 54 Temporal Low 28 32 54 Non-Temporal High 43 47 54 Non-Temporal Low 29 32 54 3.1 KHz Temporal High 39 41 54 3.1 KHz Temporal Low 29 32 54 3.1 KHz Non-Temporal High 42 43 54 3.1 KHz Non-Temporal Low 28 29 54 Coded High 43 47 54 3.1 KHz Coded High 42 43 54 AVDS916-01 • 10/03/2023 • Page 3 L-Series with LED Dimensions: Wall-Mounted Equipment Compact Strobe, Horn Strobe for Wall Compact Horn Strobes, Horn Strobes for Walls Surface Mount Back Box for Walls ( SBBRL/SBBWL) 4.82" (12.24 cm)1.85" (4.69 cm) 5.78" (14.68 cm) 1.55" (3.9 cm) 3.57" (9.1 cm) 5.38" (13.7 cm) Compact Surface Mount Back Box for Walls (SBBGRL, SBBGWL) 4.7" 119 mm 5.67" 144 mm 1.25" 32 mm 3.46" 88 mm 1.25" 32 mm 5.27" 133.9 mm 4.7" 119 mm 5.67" 144 mm 1.25" (31.8 mm) 2.07" (53 mm) 3.46" 88 mm 5.27" 133.9 mm 1.25" (31.8 mm) 2.07" (53 mm) Horn A0549-00A0613-00 A0554-01 A0617-00 A0557-00A0547-00 Strobes and Horn Strobes for Ceilings Surface Mount Back Box for Ceilings (SBBCRL, SBCWL) 6.83" diam. (173.5 mm) 1.25" (31.8 mm) 2.07" (52.6 mm) 6.92" diam. (175.77 mm) 2.5" (64 mm) A0608-00 A0546-00 L-Series with LED Dimensions: Ceiling-Mounted Equipment System Sensor® is a registered trademark of Honeywell International, Inc. 3825 Ohio Avenue • St. Charles, IL 60174 USA Phone: 800-SENSOR2 • Fax: 630-377-6495 www.systemsensor.com 3333 Unity Drive, Mississauga, ON L5L 3S6 Canada Phone: 800-SENSOR2 • Fax: 905-812-0771 www.systemsensor.ca ©2023 System Sensor. Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet. AVDS916-01 • 10/03/2023 Model Description L-Series with LED Horn Strobes P2RLED 2-Wire, Horn Strobe, Wall, Red P2RLED-B 2-Wire, Horn Strobe, Wall, Red, Bilingual P2WLED 2-Wire, Horn Strobe, Wall, White P2WLED-B 2-Wire, Horn Strobe, Wall, White, Bilingual P2GRLED 2-Wire, Compact Horn Strobe, Wall, Red P2GRLED-B 2-Wire, Compact Horn Strobe, Wall, Red, Bilingual P2GWLED 2-Wire, Compact Horn Strobe, Wall, White P2GWLED-B 2-Wire, Compact Horn Strobe, Wall, White, Bilingual P2RLED-P 2-Wire, Horn Strobe, Wall, Red, Plain P2WLED-P 2-Wire, Horn Strobe, Wall, White, Plain P2RLED-SP 2-Wire, Horn Strobe, Wall, Red, FUEGO P2WLED-SP 2-Wire, Horn Strobe, Wall, White, FUEGO PC2RLED 2-Wire, Horn Strobe, Ceiling, Red PC2RLED-B 2-Wire, Horn Strobe, Ceiling, Red, Bilingual PC2WLED 2-Wire, Horn Strobe, Ceiling, White PC2WLED-B 2-Wire, Horn Strobe, Ceiling, White, Bilingual L-Series with LED Strobes SRLED Strobe, Wall, Red SRLED-B Strobe, Wall, Red, Bilingual SWLED Strobe, Wall, White SWLED-B Strobe, Wall, White, Bilingual SGRLED Strobe, Compact, Wall, Red SGRLED-B Strobe, Compact, Wall, Red, Bilingual SGWLED Strobe, Compact, Wall, White SGWLED-B Strobe, Compact, Wall, White, Bilingual SRLED-P Strobe, Wall, Red, Plain SWLED-P Strobe, Wall, White, Plain SRLED-SP Strobe, Wall, Red, FUEGO SWLED-CLR- ALERT Strobe, Wall, White, ALERT SWLED-ALERT Strobe, Wall, White, ALERT, Amber Lens SCRLED Strobe, Ceiling, Red SCRLED-B Strobe, Ceiling, Red, Bilingual SCRLED-P Strobe, Ceiling, White, Plain SCWLED Strobe, Ceiling, White SCWLED-B Strobe, Ceiling, White, Bilingual SCWLED-P Strobe, Ceiling, White, Plain SCWLED-CLR- ALERT Strobe, Ceiling, White, ALERT L-Series Horns HRL*Horn, Red HRLA*Horn, Red, Plain, ULC HWL*Horn, White HWLA*Horn, White, Plain, ULC HGRL*Compact Horn, Red HGRLA*Compact Horn, Red, Plain, ULC HGWL*Compact Horn, White HGWLA*Compact Horn, White, Plain, ULC L-Series with LED: Ordering Information Model Description LED Lenses LENS-A3 Lens LED Amber Wall/Ceiling LENS-B3 Lens LED Blue Wall/Ceiling LENS-G3 Lens LED Green Wall/Ceiling LENS-R3 Lens LED Red Wall/Ceiling Accessories TR-2 Universal Wall Trim Ring Red TR-2W Universal Wall Trim Ring White SBBRL Wall Surface Mount Back Box, Red SBBWL Wall Surface Mount Back Box, White SBBGRL Compact Wall Surface Mount Back Box, Red SBBGWL Compact Wall Surface Mount Back Box, White TRC-2 Universal Ceiling Trim Ring, Red TRC-2W Universal Ceiling Trim Ring, White SBBCRL Ceiling Surface Mount Back Box, Red SBBCWL Ceiling Surface Mount Back Box, White Bezels† BZR Wall Red Bezel Kit BZW Wall White Bezel Kit BZGR Compact Wall Red Bezel Kit BZGW Compact Wall White Bezel Kit BZRC Horn Strobe Ceiling Red Bezel Kit BZWC Horn Strobe Ceiling White Bezel Kit Notes for L-Series With LED Horn Strobes and Strobes: All -P models have a plain housing (no “FIRE” marking on cover). All -SP models have “FUEGO” marking on cover. All -ALERT models have “ALERT” marking on cover. All -B models have “FIRE/FEU” marking on cover for use in Canadian applications. Amber lenses are not for use in Canadian applications Notes for L-Series Horns: *Horn-only models are listed for wall or ceiling use. Notes for Bezels: †Each bezel pack ships in a package of 5. Add one of the following extensions for print/language options: -F (FIRE), -AL (ALERT), -EV (EVAC), -AG (AGENT), -P (Plain), -FR (FEU), -PG (FOGO), -SP (FUEGO), -SPE (FUEGO/FIRE). Agency Listings Features • Weatherproof per NEMA 4X, IP56 • Listed to UL 1638 (strobe) and UL 464 (horn) • Compatible with System Sensor synchronization protocol and legacy SpectrAlert products • Field-selectable candela settings: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185 • Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela • Rotary switch for horn tone and three volume selections • Horn rated at 88+ dBA at 16 volts • Rated from –40°F to 151°F • Universal mounting plate with an onboard shorting spring that tests wiring continuity before devices are installed • Plug-in design with minimal intrusion into the back box • Tamper-resistant construction • Listed for ceiling or wall mounting SpectrAlert Advance offers the broadest line of outdoor horns, strobes, and horn strobes in the industry. With white or red plastic housings, wall or ceiling mounting options, and plain or FIRE-printed devices, SpectrAlert Advance can meet virtually any application requirement, including indoor, outdoor, wet, and dry applications in temperatures from −40°F to 151°F. Like the entire SpectrAlert Advance line, outdoor horns, strobes, and horn strobes for wall applications include a variety of features that increase application flexibility and simplify installation. First, field-selectable settings, including candela, automatic selection of 12- or 24-volt operation, horn tones, and three volume options enable installers to easily adapt devices to meet requirements. Next, SpectrAlert Advance devices use a universal mounting plate for both wall and ceiling applications. This mounting plate includes an onboard shorting spring that ensures wiring continuity before devices are installed, so installers can verify proper wiring without mounting the devices and exposing them to potential construction damage. Once the plates are mounted, all SpectrAlert Advance devices utilize a plug-in design with a single captured screw to speed installation and virtually eliminate costly ground faults. Outdoor devices ship with weatherproof plastic back boxes (metal back boxes are available separately) that accommodate in-and- out wiring for daisy chaining devices. Plastic back boxes feature removable side flanges and improved resistance to saltwater corrosion. Knock-outs located on the back eliminate the need to drill holes for screw-in mounting. Plastic and metal weatherproof back boxes come with ¾-inch top and bottom conduit entries and ¾-inch knock-outs at the back. A screw-in NPT plug with an O-ring gasket for a watertight seal is included with each back box. Outdoor Selectable- Output Horns, Strobes, and Horn Strobes for Wall Applications SpectrAlert® Advance outdoor audible visible products are rich with features that cut installation times and maximize profits. MEA452-05-E3023572 7300-1653:187 (outdoor strobes) 7125-1653:188 (horn strobes, chime strobes) 7135-1653:189 (horns, chimes) S4011 (chimes, horn strobes, horns) S3593 (outdoor and alert strobes) AVDS01201 SpectrAlert Advance Outdoor Horn, Strobe, and Horn Strobe Specifications Architect/Engineer Specifications General SpectrAlert Advance outdoor horns, strobes, and horn strobes shall mount to a weatherproof back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products, when used with the Sync•Circuit™ Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 9 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 17 and 33 volts. Outdoor SpectrAlert Advance products shall operate between −40 and 151 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL. The strobe shall be suitable for use in wet environments. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options shall be set by a multiple position switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn or horn strobe models shall operate on a coded or non-coded power supply. The horn strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL. The horn strobe shall be suitable for use in wet environments. Physical/Electrical Specifications Operating Temperature –40°F to 151°F (–40°C to 66°C) Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Range2 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions (including lens)5.6˝ L × 4.7˝ W × 2.5˝ D (142 mm L × 119 mm W × 64 mm D) Horn Dimensions 5.6˝ L × 4.7˝ W × 1.3˝ D (142 mm L × 119 mm W × 33 mm D) Wall-Mount Weatherproof Back Box Dimensions (SA-WBB)5.7˝ L × 5.1˝ W × 2.0˝ D (145 mm L × 130 mm W × 51 mm D) Notes: 1. Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs. 2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 cd. AVDS01201 Horn and Horn Strobe Output (dBA) Switch Position Sound Pattern dB 8–17.5 Volts 16–33 Volts 24-Volt Nominal Reverberant Anechoic DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 74 74 80 80 86 86 96 96 3 Temporal Low 71 73 76 76 83 80 94 89 4 Non- Temporal High 82 82 88 88 93 92 100 100 5 Non- Temporal Medium 78 78 85 85 90 90 98 98 6 Non- Temporal Low 75 75 81 81 88 84 96 92 7†Coded High 82 82 88 88 93 92 101 101 8†Coded Medium 78 78 85 85 90 90 97 98 9†Coded Low 75 75 81 81 88 85 96 92 †Settings 7, 8, and 9 are not available on 2-wire horn strobe. UL Max. Strobe Current Draw (mA RMS) Candela 8–17.5 Volts 16–33 Volts DC FWR DC FWR Standard Candela Range 15 123 128 66 71 15/75 142 148 77 81 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High Candela Range 135 NA NA 228 207 150 NA NA 246 220 177 NA NA 281 251 185 NA NA 286 258 UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, Standard Candela Range (15–115 cd) DC Input 8–17.5 Volts 16–33 Volts 15 15/75 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, High Candela Range (135–185 cd) DC Input 16–33 Volts FWR Input 16–33 Volts 135 150 177 185 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 UL Max. Horn Current Draw (mA RMS) Sound Pattern dB 8–17.5 Volts 16–33 Volts DC FWR DC FWR Temporal High 57 55 69 75 Temporal Medium 44 49 58 69 Temporal Low 38 44 44 48 Non-Temporal High 57 56 69 75 Non-Temporal Medium 42 50 60 69 Non-Temporal Low 41 44 50 50 Coded High 57 55 69 75 Coded Medium 44 51 56 69 Coded Low 40 46 52 50 UL Current Draw Data Horn Tones and Sound Output DataCandela Derating For K series products used at low temperatures, listed candela ratings must be reduced in accordance with this table. Strobe Output (cd) Listed Candela Candela rating at –40°F 15 Do not use below 32°F15/75 30 75 44 95 70 110 110 115 115 135 135 150 150 177 177 185 185 3825 Ohio Avenue • St. Charles, IL 60174 Phone: 800-SENSOR2 • Fax: 630-377-6495 ©2012 System Sensor. Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet. AVDS01201 • 3/12 SpectrAlert Advance Diagrams Model Description Wall Horn Strobes P2RK*†2-Wire Horn Strobe, Standard cd, Red, Outdoor (includes plastic weatherproof back box) P2RHK*†2-Wire Horn Strobe, High cd, Red, Outdoor (includes plastic weatherproof back box) P2WK*†2-Wire Horn Strobe, Standard cd, White, Outdoor (includes plastic weatherproof back box) P2WHK*†2-Wire Horn Strobe, High cd, White, Outdoor (includes plastic weatherproof back box) P4RK†4-Wire Horn Strobe, Standard cd, Red, Outdoor (includes plastic weatherproof back box) P4WK 4-Wire Horn Strobe, Standard cd, White, Outdoor (includes plastic weatherproof back box) P2RHK-120 2-Wire Horn Strobe, High cd, Red, Outdoor, 120 V (includes plastic weatherproof back box) Wall Strobes SRK*†Strobe, Standard cd, Red, Outdoor (includes plastic weatherproof back box) SRHK*†Strobe, High cd, Red, Outdoor (includes plastic weatherproof back box) SWK*†Strobe, Standard cd, White, Outdoor (includes plastic weatherproof back box) SWHK*†Strobe, High cd, White, Outdoor (includes plastic weatherproof back box) Horns HRK†Horn, Red, Outdoor (includes plastic weatherproof back box) Accessories SA-WBB Red, Metal Weatherproof Back Box SA-WBBW White, Metal Weatherproof Back Box SpectrAlert Advance Ordering Information Notes: * Add “-P” to model number for plain housing (no “FIRE” marking on cover), e.g., P2RK-P. † Add “-R” to model number for weatherproof replacement device (no back box included), only for use with weatherproof outdoor flush mounting plate, WTP and WTPW. “Standard cd” refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. “High cd” refers to strobes that include 135, 150, 177, and 185 candela settings. When replacing standard outdoor units both the device and back box must be replaced. 4.7˝ 5.6˝ 6.8˝ Dia. 2.5˝ 2.5˝ Wall-Mount Horn Strobes Wall Plastic Weatherproof Back Box Wall-Mount Horn Strobe with Plastic Weatherproof Back Box 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 FEATURES & BENEFITS • Single contact monitor • Support for Class A and Class B wiring • Fully supervised • Panel controlled status LED that flashes green in normal state and is solid red in alarm • SEMS screws for easy wiring • UL Listed • Rotary address switches for fast installation SK-MONITOR Intelligent Monitor Module The SK-MONITOR is an addressable monitor module for use with Honeywell Silent Knight Series fire alarm control panels (FACPs). The SK-MONITOR is intended for use in intelligent, two-wire systems, where individual address of each module is selected using the built-in rotary switches. The SK-MONITOR supports Class A supervised or Class B supervised wiring to the load device. Conventional 4-wire smoke detectors can be monitored for alarm and trouble conditions. INSTALLATION The SK-MONITOR mounts directly into a 4” square electrical box. The box must have a minimum depth of 2-1/8”. A surface mount electrical box (System Sensor® PN SMB500) is available from Silent Knight.SK-MONITOR For a complete listing of all compliance approvals and certifications, please visit www.silentknight.com. Microsoft, Windows, and the Windows Logo are registered trademarks or trademarks of Microsoft Corporation. Silent Knight®, System Sensor® and Honeywell® are registered trademarks of Honeywell International, Inc. This document is not intended to be used for installation purposes. We try to keep our product information up-to date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For Technical Support, call 800-446-6444. SK-MONITOR Technical Specifications PHYSICAL Height: 4.5”H x 4” W x 1.25”D (11.4 X 10.2 X 3cm) Shipping Weight: 6.3 oz (196 g) ELECTRICAL Operating Voltage: 15 – 32VDC Current Draw (LED on): 5.0mA max Operating Current (LED flashing): 375 μ A Standby Current: 400 μ A max @ 24 VDC (one communication every 5 sec with 47K EOL); 550 μ A max @ 24 VDC (one communication every 5 sec with EOL <1K) 5.5 mA (with LED latched on) LED Current: 5.5 mA (with LED latched on) End-of-Line Resistance: 47K W Initiating Device Circuit Wiring Resistance: 1,500 W max SLC Loop Resistance: 40 W max. ENVIRONMENTAL Operating Temperature: 32ºF – 120ºF (0ºC – 49ºC) Humidity: 10% – 93% non-condensing ORDERING INFORMATION SK-MONITOR: Monitor Module ACCESSORIES. SMB500: 4” Square surface mount electrical box COMPATIBILITY The SK-MONITOR is compatible with the following Honeywell Silent Knight fire alarm control panels: 6820: Addressable fire alarm control panel 6820EVS: Addressable fire alarm control panel with an emergency mass notification system. 6808: Addressable fire alarm control panel 6700: Addressable fire alarm control panel 5700: Addressable fire alarm control panel 5808: Addressable fire alarm control panel 5820XL: Addressable fire alarm control panel 5820XL-EVS: Addressable fire alarm control panel with an emergency mass notification system Doc 350131 | Rev G | 11/17 © 2017 Honeywell International Inc. For more information Learn more about Honeywell Silent Knight and other products by visiting www.silentknight.com Honeywell Silent Knight 12 Clintonville Road Northford, CT 06472 800-328-0103 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868 500 Cherry Street SE 360.353.3157 Olympia WA 98501 LIC# BETSCEC157BP | UBI: 600-535-868