20160114 Energy Calcs 04182016�Envelope Summary Zones 4c/5b ENV-SUM_;
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Oct 2013
Project Info
Project Address 2016 -09 Yelm High III
Date 4/18/2016
Compliance forms
1315 Yelm Ave. West
For Building Department Use
Yelm, WA 96597
do not require a
password to use.
Instructional and
Applicant Name: Modern Building Systems, Inc.
calculating cells are
write - protected.
Applicant Address: 9493 porter Rd., Aumsville, OR 97325
Applicant Phone: 503- 749 -4949
Project Description
❑ New Building ❑ Addition ❑ Alteration ❑ Change of Occupancy /Conditioning
Compliance Path
O Prescriptive p * Component Performance O Total Building Performance
Selection required to enable forms.
Occupancy Group
OQ Commercial O Group R - R2 & R3 over 3 stories and all R1
Selection required to enable forms.
Vertical Fenestration and
Total Vertical Gross Exterior
Skylight Area Calculation
Fenestration Above Grade % Vertical
If complying via the Prescriptive path,
(rough opening) divided by Wall Area times 100 equals Fenestration
192.0 — 3592.0 X 100 — 5.3%
enter values for vertical fenestration,
skylights, gross walls and roof on this
ENV -SUM worksheet. If complying via
the Component Performance path, enter
Gross Exterior
these values in the ENV -UA worksheet.
Total Skylight divided by Roof Area times 100 equals % Skylight
These values auto -fill from ENV -UA and
are write - protected on ENV -SUM.
0.0 8283.0 X 100 = 0.0%
Fenestration Area
Vertical VERTICAL FENESTRATION AREA COMPLIES
Fenestration Area
Compliance
Skylight Area SKYLIGHT AREA COMPLIES
Vertical Fenestration
O 50% or more of the floor area is within a daylight zone per C402.3.1.1
Alternates
O High Performance Fenestration U- factors and SHGC per C402.3.1.3
Compliance Method
❑ Skylight area 3% or greater, VT -0.40 or greater
Single Story Spaces
❑ Skylight effective aperture 1 % or greater, provide calculation
Requiring Skylights
❑ Space eligible for exception
Requires a minimum of 50% of floor area to be within a skylight daylight zone for specific
space types. Refer to C402.3.2 for requirements.
❑ Project has semi - heated spaces as defined per C402.1.4
❑ Applying wall exception to semi - heated spaces
1. Semi - heated spaces may comply under Prescriptive or Component Performance compliance
Semi - Heated Spaces
path.
2. Semi - heated spaces shall be documented separately from other conditioned spaces — provide
separate compliance forms for each conditioned space type.
3. Envelope elements separating semi - heated from other conditioned spaces shall comply with
exterior thermal envelope requirements.
❑ Walk -in Cooler ❑ Walk -in Freezer
❑ Refrigerated Warehouse Cooler 1:1 Refrigerated Warehouse Freezer
Refrigerated Spaces
Refrigerated spaces shall comply under the Prescriptive Path only. Compliance documentation for
these areas may be combined with non - refrigerated areas in the ENV - PRESCRIPTIVE form. Refer
to C402.5 and C402.6 for requirements.
Mixed Occupancy
Project includes more than one occupancy type and /or level of space conditioning. Multiple
and/or
compliance forms may be required. Select all that apply to scope of project:
Space Conditioning
❑ Commercial ❑ R2 & R3 over 3 stories and all R1 ❑ Refrigerated Space
❑ Fully Conditioned ❑ Semi - Heated ❑ Low Energy*
❑ R2 & R3 - 3 stories or less
*Low energy areas are exempt from all thermal envelope provisions and compliance forms for
these areas are not required. Refer to C101.5.2 for exemption.
L
G r, for Commercial RAldinas includina R2 & R3 over 3 stories and all R1 Revised Oct 2013
1uiz4vvasnmgiuli OWRi CHUIYY l uc vviiiF ui v v.... _. _. _. -_ _
Date 04/ 6
Project Address 2016 -09 Yelm High 111
For Building Department Use
Occupancy Group * Commercial O Group R
Change in occupancy or space conditioning O
Note - Proposed UA may exceed Target UA by 10% per C101.4.4 and C101.4.5
Fenestration Area as % gross above -grade wall area 5.31-o Max. Target: 30.0%
Skylight Area as % gross roof area 0.0 % Max. Target: 5.0%
Vertical Fenestration Alternates: None Selected on ENV -SUM
Notes: 1: If vertical fenestration or skylight area exceeds maximum allowed per C402.3.1, then Target Area Adjustment of all applicable envelope
elements will be calculated by the compliance form. Refer to Target Area Adjustments worksheet for this calculation.
2: U- factors shall come from Appendix A, Chapter C303, or calculated per approved method as specified in C402.1.2.
Building Component
Proposed UA
Target UA
Provide source of U- factor, page /plan # of assembly detail & ID
U- factor x Area (A) = UA (U x A
U- factor x Area (A) = UA (U x A)
R=38 ID: Sht. A3.1, Calculated U- Factor, See Attached
0.029 8283 240.2
0.034 8283 281.6
Above Deck Insulation U -0.034
Y
R- ID:
0
R= ID:
-6
R= ID:
0.031
Metal Building U -0.031
w
o
m
R- ID:
R= ID:
R= ID:
0.021
Single raft, attic, other U -0.021
R- ID:
0
R= ID:
R= ID:
0.055
Steel /metal frame U -0.055
u
R= ID:
R= ID:
a�
o
R= ID:
0.052
Metal Building U -0.052
m
ID:
Q
R=
R= ID:
�
O
R= 21 ID: Sht. A3.1, Calculated U- Factor, See Attached
0.050 3316 165. B
o .054 3316 179.1
Wood Frame, other U -0.054
a)
o
R= ID:
CU
o
3:
R= ID:
R= ID:
U -0.104
U)
R- ID:
2i
R= ID:
rAssumed
t°
R= ID:
o be Mass Wall U -0. 104
o �
R= ID:
Z a)
m
R= ID:
CD
R= ID:
R= ID:
0.031
Mass Floor U -0.031
m
R= ID:
o
R= ID:
-o
R=30 ID: Sht. A3.1, T.A105.1(1) Default (Joists,
0.029
9283
240.2
0.029 e2s3 240.2
Joist/Framing U -0.029
u
E
R= ID: 0 Perimeter)
LL
R= ID:
F- factor
x Perimeter
= UA(U x A)
F- factor x Perimeter = UA (U x A)
R= ID:
0.540
Slab -On -Grade U -0.54
is
ID:
r
R=
DS
R= ID:
o
a
R= ID:
0.550
Heated Slab -On -Grade U -0.55
�n
a
R- ID:
=
R= ID:
`Proposed non - residential CMU walls meeting Table C402.1.2 Area UA Area UA
Footnote D requirements can use the target U -value of 0.104 rather Page 19 8 8 2 646
1 �88 701
than Appendix A values. Show footnote requirements in plans. Subtotal
Component Performance Compliance (UA) UA COMPLIES
• • • • • • • •
n, In, ... ti,..,.�..., et .,+e V:or rnr e Comnlinnra Fnrmc fnr Cnmmercial Buildinas Includlncl R2 & R3 over: Revised Oct 2013
Project Address 2016 -09 Yelm High 111
Date 04/18/2016
Fenestration Area as % gross above -grade wall area 5.3% Max. Target: 3 0.0 %
For Building Department Use
Skylight Area as % gross roof area Max. Target: 5.0%
Notes: 1: If vertical fenestration or skylight area exceeds maximum allowed per C402.3.1, then Target
Area Adjustment of all applicable envelope elements will be calculated by the compliance form.
Refer to Target Area Adjustments worksheet for this calculation.
2: Provide NFRC rated U- factor or default U- factor from Appendix A for the fenestration assembly
thermal performance (combination of frame and glazing).
3: Fenestration that separates conditioned space from a non - conditioned or semi - conditioned
Building Component
Proposed UA
Target UA
Provide source of U- factor, page /plan # of assembly detail & ID
U- factor x Area (A) = UA (U x A
U- factor x Area (A) = UA (U x A)
U= 0 .3e ID: Door 1, Sht. A3.1, NFRC Certified
0.380
4z 16.0
0.37 94 31.1
Opaque Swing Doors U -0.37
�
0
U= 0.38 ID: Door 2, Sht. A3.1, NFRC Certified
0.380
42 16.0
m
U= ID:
3
U= ID:
U)
U= ID:
a N
U= ID:
0.37
Opaque rollup & sliding U -0.37
o
U- ID:
U= ID:
@
U= 0.34 ID: Window & B, Sht. A3.1, NFRC Certified
0.34
192
65.3
0.30 192 57.6
Non -Metal Frame U -0.30
W
U= ID:
0
U= ID:
Z
U= ID:
�
U= ID:
0.38
Metal Frame, Fixed U -0.38
4
--
U= ID:
m
U= ID:
m
a)
U= ID:
L
U= ID:
0.40
Metal Frame, Operable U -0.40
Cc
°-
U= ID:
Z
U= ID:
U= ID:
U= ID:
0.60
Metal Entrance Door U -0.60
U= ID:
U= ID:
U= ID:
U= ID:
0.50
All types U -0.50
o
n
U= ID:
U= ID:
u)
Q
U= ID:
Area UA Area vri
Page 2 Subtotal 276 97 276 89
To comply: Page 1 Subtotal 19882 646 19882 701
1) Proposed Total UA shall not exceed Target Total UA.
2) Proposed Total Area shall equal Target Total Area. Total 20158 743 2 015 8 790
Component Performance Compliance (UA) UA COMPLIES
4
If vertic�nl fenestration area exceeds maximum allowed per Section C402.3.1, then Target Area Adjustment of all applicable envelope elements is
�,equired. This worksheet automatically calculates these adjustments and updates target areas in the ENV -UA and ENV -SHGC worksheets. Information
shown in this worksheet is for reference only and is write - protected. Submit this Target Area Adjustment form with ENV -UA and ENV -SHGC forms.
VF = Vertical fenestration NW = Net above qrade wall (excludes fenestration and doors.) I
DR = Opaque doors Gross Exterior Above -Grade Wall Area= VF + NW + DR
A(; = Ahnve -grade
Proposed Areas
Total Vertical Excess Vertical Target Vertical
Fenestration Fenestration Fenestration
192.0 - = 192.0
Net AG Wall Area Excess Fenestration Target Net Wall Area
3316.0 + = =3316 .0
UA Adjustments
Vertical Fenestration
Non -metal frame
Metal frame, fixed
Metal frame, operable
Metal frame, entrance door
Above -grade Wall
Steel Frame
Metal Building
Wood / Other frame
Mass
Sum of Proposed
SHGC x A Adjustments
Non -North Vertical Fenestration
PF < 0.2
0.2 s PF < 0.5
PF ? 0.5
North Vertical Fenestration
PF < 0.2
0.2!5 PF < 0.5
PF > 0.5
-885.6 Multiplier applied to all
Total Vertical
Vertical Fenestration ->
VF=
192.0
Target VF Multiplier
MM
- 192.0
Opaque >
NW=
3316.0
DR=
84. 0
Gross Exterior
Max Vert. Fen. %
Proposed Opaque Above-
Grade Wall Areas to
Maximum Target
AG Wall Area
(C402.3.1)
Vert. Fen. Area
3592.0
30.0%
100 =
1077.6
X -
I otal Vertical
Delta Vertical
0
Excess Vertical
Fenestration
Maximum Target
Fenestration
Fenestration
192.0
-
1077.6
=
-885.6
greater
=
Total Vertical Excess Vertical Target Vertical
Fenestration Fenestration Fenestration
192.0 - = 192.0
Net AG Wall Area Excess Fenestration Target Net Wall Area
3316.0 + = =3316 .0
UA Adjustments
Vertical Fenestration
Non -metal frame
Metal frame, fixed
Metal frame, operable
Metal frame, entrance door
Above -grade Wall
Steel Frame
Metal Building
Wood / Other frame
Mass
Sum of Proposed
SHGC x A Adjustments
Non -North Vertical Fenestration
PF < 0.2
0.2 s PF < 0.5
PF ? 0.5
North Vertical Fenestration
PF < 0.2
0.2!5 PF < 0.5
PF > 0.5
-885.6 Multiplier applied to all
Total Vertical
Proposed Vertical
Fenestration
Target VF Multiplier
Fenestration Areas to
calculate Target Vertical
- 192.0
= 1. 0 0
Fenestration Area
Net Wall
Target Net Wall Mult.
Multiplier applied to all
3316.0
= 1. 0 0
Proposed Opaque Above-
Grade Wall Areas to
calculate Target Above-
Proposed Area Target VF Mult. Target Area
192.0 X 1.00 = 192.0
X _
X _
X I Target areas in shaded
Proposed Area Target Net Wall Mult. Target Area boxes are applied to
_ target areas on ENV -UA
X
3316.0 X 1.00 = 3316.0
X
Sum of target above -grade
3 5 0 8. 0 Sum of Target 3508.0 wall and vertical
fenestration areas are
calculated to equal the
sum of proposed
Proposed Area Target VF Mult. Target Area
192.0 X 1.00 = 192.0
X
X
SHGC target areas in
shaded boxes are applied
to target areas on ENV -
SHGC
'kvliaht Taraet Area Adiustment Calculations
If skylight area exceeds maximum allowed per Section C402.3.1, then Target Area Adjustment of all applicable envelope elements is required. This
worksheet automatically calculates these adjustments and updates target areas in the ENV -UA and ENV -SHGC worksheets. Information shown in this
[SKY= Ckvliaht I NR - Net roof (excludes skylight) I Gross Exterior Roof Area = SKY + NR
Proposed Areas
Skylight (Horizontal Fenestration) -I SKY=
Opaque Roof -> NR= 8283. 0
Gross Exterior
Max Skylight %
Maximum Skylight
Roof Area
(0402.3. 1)
Fenestration Area
8283.0 X
5.0% — 100 = 414.2
Total Skylight Area
Maximum Target Delta Skylight Area
0 Excess Skylight
-414.2
:j greater =
-414.2
Total Skylight E Skylight Target Skylight A Total Skylight Area Target SL Multiplier Multiplier applied to all
)I9 ht Area Excess Area Proposed Skylight Areas
to calculate Target
SkylightArea
Net Roof Area Excess Skylight Target Net Roof Area Net Roof Target Net Roof Mult.
8283.0 = 8283.0 — 8283.0 = 1.00 Multiplier applied to all
Proposed Opaque Roof
Areas to calculate Target
UA and SHGC x A Adjustments
Skylight
All
Roof
Insulation Above Deck
Metal Building
Attic/ All Others
Proposed Area Target SL Mult. Target Area
X
Proposed Area Target Net Wall Mult. Target Area
8283.0 X 1.00 = 8283.0
X
X
Sum of target roof and
skylightareas are
8283.0 calculated to equal the
sum of proposed
Sum of Proposed 8283 . 0 Sum of Target
on10 W—hi., tr,n Fnornv f'nric C m—li —ro Fnrmc fnr r:nmmarrial Ri ilriinns inchiriinn Ri & R3 over 3 stories and all R1 Revised Oct 2013
Project Address 2016 -09 Yelm High III
Date 04/18/2016
0 5. 3 % Max. Target: 30%
Fenestration Area as /o gross above -grade wall area 9
For Building Department Use
Skylight Area as % gross roof area Max. Target: 5%
Vertical Fenestration Alternates: None Selected on ENV -SUM
Notes: 1 - Proposed vertical fenestration and skylight areas entered in ENV -SHGC must match proposed
fenestration areas in ENV -UA.
192 76.8
2 - If Target Area Adjustment is required per ENV -UA, then target areas will be automatically
0
adjusted in ENV -SHGC. Refer to Target Area Adjustments worksheet for this calculation.
0.2 :5PF <0.5 0.48
3 - Provide NFRC rated SHGC or default from Table C303.1.3(3) for fenestration assembly SHGC.
PF ? 0.5 0.64
4 - Fenestration that separates conditioned space from a non - conditioned or semi - conditioned
ID:
space shall be included in this worksheet.
Skylights Proposed SHGC
Target SHGC
Provide source of SHGC, page /plan # of assembly detail & ID SHGC x Area (A) = SHGC x I
SHGC x Area (A) = SHGC x A
ID:
0.35
SHGC 0.35
ID:
ID:
0
ID:
SHGC will sum fenestration area by PF
category.
ID:
0
i
Totals
ID:
Totals
All Non -North Vertical Fenestration+ Proposed SHGC
Target SHGC ++
Provide source of SHGC, page /plan # of assembly PF SHGC* x Area (A) = SHGC x A
detail & ID
PF SHGC x Area (A) = SHGC x A
Category
ID: Window A, Sht. A3.0, NFRC Certified
0 0.30 192
58
PF < 0.2 0.40
192 76.8
ID:
0
0.2 :5PF <0.5 0.48
PF ? 0.5 0.64
ID:
0
++ If projection factor (PF) credits are
ID:
0
ID:
0
applied to the proposed design, Target
ID:
0
SHGC will sum fenestration area by PF
category.
ID:
0
i
ID:
0
ID:
0
ID:
0
+ If projection factor credit is applied, then vertical Totals
192.0
57.6
Totals
192.0
76.8
fenestration must be entered in the correct table according to
orientation. It credit is not applied Men all vertical
fenestration can be entered in either table.
* Note: Fenestration that separates conditioned space from a
non - conditioned or semi - conditioned space shall be listed
here with a proposed SHGC equal to the target value.
North Vertical Fenestration+ Proposed SHGC Target SHGC ++
Provide source of SHGC, page /plan # of assembly PF SHGC* x Area (A) = SHGC x A PF SHGC x Area (A) = SHGC x A
detail & ID Category
ID: 0 PF <0.2 0.40
ID: 0 0.2 <_PF <0.5 0.44
ID: 0 PF ? 0.5 0.48
ID: 0 ++ If projection factor (PF) credits are applied
ID: 0 1 to the proposed design, Target SHGC will
ID: 0 sum fenestration area by PF category.
ID: 0
North Total
Area I SHGC x Al Area I SHGC x A
To comply, the Proposed total SHGC x A for all fenestration (vertical Grand I Grand
& skylights) shall not exceed the Target total SHGC x A. Total 192.0 57 .6 Total 192.0 76.8
Component Performance Compliance (SHGC) SHGC COMPLIES
Y
,$uilding Permit Plans Checklist, ••
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1
Project Address 2016 -0e Yelm High iii Date 4/18/2016
The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy
Code, Commercial Provisions.
Applicability
Code
Location in
Building
(yes,no,na)
Section
Component
Compliance information required in permit documents
Documents
Department Notes
SCOPE
na
C101.5.2
Low energy spaces
Low energy spaces identified on plans
na
C101.5.2.1
Semi - heated spaces
Semi - heated spaces identified on plans
C402.1.4
C402.5
Cooler and freezer
Walk -in and refrigerated warehouse cooler and freezer spaces identified on
na
C402.6
spaces
plans
na
C101.4.6
Mixed occupancy
Spaces with different occupancy requirements identified on plans
Change of
Existing F, S and U- occupancy building spaces undergoing a change of
na
C101.4.4
occupancy /space
occupancy or space conditioning that require compliance are identified on
C101.4.5
conditioning
plans
ENVELOPE PROVISIONS
yes
C303.1
Insulation
Indicate identification mark shall be applied to all insulation materials
Ao o
identification
.
C303.1.3
Fenestration product
Fenestration products shall be labeled with rated U- factor, SHGC, VT, and
yes
C402.4.3
rating
leakage rating
A0.0
Indicate installation methods, thicknesses, densities and clearances to achieve
C303.1.1
General insulation
the intended R -value of all insulation materials;
yes
C402.2
installation
Where two or more layers of rigid insulation will be used, indicate that edge
joints between layers are staggered
A3.0 S3.0
Indicate R- value(s) of cavity /continuous insulation on roof sections,
Indicate framing materials on roof sections;
Indicate method of framing for ceilings below vented attics and vaulted ceilings
yes
C402.2.1
Roof assembly
per At 02.2 (std, adv);
insulation
Provide area - weighted calculations for sloped insulation installed entirely above
deck;
Indicate R- values for thermal spacers and each insulation layer, and liner
system (LS) method for metal building roofs
A3.0 a S3.0
Skylight curb
Indicate curb insulation R -value on roof section if not included in skylight NFRC
na
C402.2.1
insulation
rating
Indicate R- value(s) of cavity /continuous insulation on wall sections,
Indicate framing materials on wall sections;
Indicate method of framing for wood const per At 03.2 (std, int, adv);
C402.2.3
Above /below grade
yes
C402.2.4
Indicate mass of masonry walls;
C303.2.1
wall insulation
Indicate loose -fill core insulation material, percentage of cores filled, and
frequency of grouted cores and bond beams for masonry walls;
Indicate method of protection of exposed exterior basement/crawlspace wall
insulation
Indicate insulation R- values of ceilings, walls, doors, floors on sections;
Walk -in /refrigerated
na
C402.5
warehouse cooler
Indicate method of minimizing door infiltration;
C402.6
and freezer insulation
Indicate type(s) of transparent doors and windows
-
Indicate rated U- factor (swinging) or R -value (roll -up /sliding) on wall sections -
yes
C402.2.7
Opaque doors
applies to doors with less than 50% glazed area
A3.0
Indicate R- value(s) of cavity /continuous insulation on floor sections;
Floor over outdoor or
yes
C402.2.5
unconditioned space
Indicate framing material on floor sections,
insulation
Indicate mass of masonry floors
A3.0 a S3.0
Indicate R -value of continuous insulation on wall section or foundation detail;
C402.2.6
Slab -on -grade floor
Indicate insulation extends down vertically and /or horizontally the required
na
C303.2.1
insulation
distance from top of slab;
Indicate method of protection of exposed exterior slab edge insulation
Indicate R -value of continuous insulation on wall section or foundation detail;
C402.2.6
Radiantly heated slab
Indicate insulation extends down vertically from top of slab and then horizontally
na
on -grade floor
C303.2.1
insulation
under the entire slab,
Indicate method of protection of exposed exterior slab edge insulation
Radiant heating
Indicate insulation R -value behind radiant panels, U- bend /headers and bottom
na
C402.2.8
system insulation
surface of radiantly heated floors (other than radiantly heated slab -on- grade)
RZOlding Permit Plans Checklist, ••
2 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1
F201
ject Address 2016 -09 Yelm High ul
Date 4/18/2016
licability
Code
Location in
Building
s,no,na)
Section
Component
Compliance information required in permit documents
Documents
Department Notes
Vertical fenestration
Provide calculation for total vertical fenestration area as percentage of gross
yes
C402.3.1
maximum area
above grade wall area
ENV SUM
na
C402.3.1.2
Skylight maximum
Provide calculation for total skylight area as percentage of gross roof area
area
Indicate U- factors, SHGC and VT values in fenestration schedules;
C402.3.3
U- factors, SHGC and
An area - weighted U -value may be used for all fenestration elements that qualify
yes
C402.3.1.3
VT for all fenestration
within the same fenestration category per Table C402.3;
C303.1.3
assemblies
Indicate if values are NFRC or default. If default then specify frame type,
glazing layers, gap width, low-e coatings, gas -fill.
A3.0
Provide calculations showing that percentage of overall conditioned floor area
C402.3.1.1
Increased max.
in the daylight zone is equal to or greater than 50 %;
na
Chap.2
vertical fenestration
area with daylighting
Indicate method of daylighting control in lighting equipment schedules;
Definition
controls
Indicate VT of vertical fenestration is at least 1.1 times the rated SHGC
Increased max.
Indicate high performance U- factors and SHGC values in fenestration
vertical fenestration
schedules;
na
C402.3.1.2
area with high-
An area - weighted U -value may be used for all fenestration elements that qualify
performance glazing
within the same fenestration category per this section
-
C402.3.3
Permanent shading
Provide projection factor calculations (Equation C4 -2) and associated SHGC
na
C402.3.3.1
devices
multipliers for north and non -north orientations
_
Provide calculations for percentage of conditioned floor area located within a
skylight daylight zone,
Provide calculations for percentage of skylight area to daylight zone under
na
C402.3.2
Single story spaces
skylights, hts, OR;
Yl 9
requiring skylights
Provide calculations for percentage of overall skylight effective aperture
(Equation C4 -1);
Indicate haze factor of skylight glazing material or diffuser
_
AIR LEAKAGE
Indicate location of continuous air barrier on plans and sections;
C402.4.2
Air barrier
yes
construction and
Provide details for all joints, transitions in materials, penetrations in air barrier
C402.4.2
sealing
and note method of sealing (caulked, gasketed, or other approved method)
A3.0
Indicate locations of all stairway and shaft vents;
Provide leakage rating of motorized dampers in mechanical equipment
na
C402.4.5.1
Stairway and shaft
schedules;
vents
Indicate method of emergency operation - activation of fire alarm or interruption
of power
Indicate locations of all outside air intakes, exhausts and relief outlets, includina
Outdoor air intakes,
those integral to mechanical equipment;
yes
C402.4.5.2
exhausts and relief
Provide in mechanical equipment schedules leakage rating of dampers, identify
openings
whether motorized or gravity, and note any exceptions taken
M1.0
Recessed lighting in
Indicate IC rating of fixtures in lighting equipment schedules;
na
C402.4.8
building envelope
Indicate method of sealing between light fixture housing and wall or ceiling
na
C402.4.6
Loading dock seals
Indicate weather seal at cargo and loading dock doors
-
Indicate locations and dimensions of vestibules;
na
C402.4.7
Vestibules
For unconditioned vestibules, indicate which envelope assembly (interior or
exterior) complies with the requirements for a conditioned space
Indicate air barrier test method in accordance with ASTM E779 or approved
equivalent;
C402.4 -
Air barrier building
include the following requirements in project documents: (1) air barrier test
yes
report shall be submitted to jurisdiction once test is completed; (2) if test results
1.2.3
test
exceed 0.4 cfm /ft2 at 0.3 in. wg then visually inspect air barrier and seal noted
sources of leakage; (3) submit a follow -up report to jurisdiction noting corrective
measures taken
1A0.0
If "no" is selected for any question, provide explanation:
End of Building Permit Plans Checklist
Roof U -Value
At Fra ing Members with Insulation Below(7.5 %)
Layers
A B C D E F
`o `o
Zb
w c
Layer
Description
Detail
R -Value
Exterior Surface
Moving Air 15 MPH
= 0.023
0.170
A
Roofing
Fiberglass Comp. Shingles
0.440
B
Felt
(2) Layers 15# Felt
0.060
C
Sheathing
7/16" O.S.B.
1.155
D
Rafters /Blocks
2x10 DF at 24" O.C.
9.805
E
Insul. Below
Framing
R9 Cellulose (2.5 ")
9.000
F
Interior Surface
Still Air
0.610
Total R- Values
21.240
[-U-Value (1 /R- Value)
0.047
At Framing Members with Insulation Blocks Below (2.5 %)
Layers
A B C I D I E F
`o_ `o_
w E
Layer
Description
Detail
R -Value
Exterior Surface
Moving Air 15 MPH
0.170
A
Roofing
Fiberglass Comp. Shingles
0.440
B
Felt
(2) Layers 15# Felt
0.060
C
Sheathing
7/16" O.S.B.
1.155
D
Rafters /Blocks
2x10 DF at 24" O.C.
9.805
E
Insul. Blocks
(5) at 2 x4 x 9" Long
3.710
F
Interior Surface
Still Air
0.610
Total R- Values
15.950
U -Value (1 /R- Value)
0.063
At Insulation (90 %)
Layers
A B C D E F
o `o
X c
Layer
Description
Detail
R -Value
Exterior Surface
Moving Air 15 MPH
0.170
A
Roofing
Fiberglass Comp. Shingles
0.440
B
Felt
(2) Layers 15# Felt
0.060
C
Sheathing
7/16" O.S.B.
1.155
D
Insulation
R -38 Cellulose (10.6 ")
38.000
E
F
Interior Surface
Still Air
0.610
Total R- Values
40.435
U -Value (1
/R- Value)
0.025
U -Value at Framing /Insul
U -Value at Framing with Blk
U -Value at Insulation
0.047 x
0.075
= 0.004
0.063 x
0.025
= 0.002
0.025 x
0.900
= 0.023
Total Roof U -Value
0.029
2012 Washinaton State Enerqv Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Info
Project Address 2016 -09 KCDA Yelm High III
Date 4/14/2016
Compliance
1315 Yelm Ave. West
For Building Department Use
forms do not
require a
Yelm, WA 98597
Applicant Name: Modern Building Systems, Inc.
password to
use.
Applicant Address: 9493 Porter Rd, Aumsville, OR 97325
Instructional and
calculating cells
Applicant Phone: 503 - 749 -4949
are write-
Project Description
0 New Building ❑ Addition ❑ Alteration ❑ Plans Included
Lighting Compliance Path
Lighting Power Density Calculations ❑ Total Building Performance
is
(If Total Building Performance then only LGT -CHK required.)
Lighting Power Allowance
0 Building Area Method O Space -By -Space Method
Method Selection required to
enable LPs, forms
Interior Lighting System
Lay -in and surface mount ceiling fluorescent fixtures with electronic ballasts controlled by
Description
occupancy sensors, daylight sensors and /or wall switches.
Briefly describe lighting
system type and features.
Additions and Change of Space Use (C101.4.3 & C101.4.4)
❑ Addition area or Change of Space Use area complies with all applicable provisions as stand alone project
❑ Addition area is combined with existing building lighting systems to demonstrate compliance with all applicable
provisions per C101.4.3
Provide Building Area Method (LTG - INT -BLD) or Space -By -Space Method (LTG -INT- SPACE) Compliance Form. Document maximum
allowed and proposed (including existing if applicable) lighting wattage of Addition or Change of Use space. Provide applicable lighting
controls per C405.2 and commissioning of lighting controls per C405.13.
Alterations, Renovations and Repairs (C101.4.3.1)
❑ 60% or more of luminaires in space replaced
Provide Building Area Method (LTG -INT -BLD) or Space -By -Space Method (LTG -INT- SPACE) Compliance Form. Document maximum
allowed wattage within the lighting retrofit space in Maximum Allowed Wattage table and proposed (including existing) lighting wattage in
Proposed Wattage table. Retrofit and non - retrofit spaces shall be documented separately using multiple forms.
❑ Less than 60% of luminaires in space replaced
Provide a separate Space -By -Space Method (L TG-INT-SPA CE) Compliance Form for this retrofit area. Document existing total wattage
within the lighting retrofit space in cell provided in the Maximum Allowed Wattage table. Document proposed (including existing) lighting
wattage in the Proposed Wattage table.
❑ Lamp and /or ballast replacement within existing luminaires only — existing total interior building wattage not increased
❑ New wiring installed to serve added fixtures and /or fixtures relocated to new circuit
Provide applicable manual lighting controls (C405.2.1), occupancy sensors (C405.2.2.2), daylight zone controls (C405.2.2.3), specific
application controls (C405.2.3), and commissioning of lighting controls per C405.13
❑ New or moved lighting panel
Provide all applicable lighting controls as noted for New Wring, automatic time switch controls (C405.2.2.1), and commissioning of lighting
controls per C405.13.
❑ Space is reconfigured - luminaires unchanged or moved only
Provide all applicable lighting controls as noted for New Wring and commissioning of lighting controls per C405.13.
❑ No changes are being made to the interior lighting and space use not changed.
2012 Washington State Enerov Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 2016 -09 KCDAYelm High III
Date 4/14/2016
Lighting Alterations, Renovations & Building Additions
For Building Department Use
O Less than 60% O 60% or more O Stand alone O Addition
Watts
Proposed
Notes:
Page E2.0
a. Lighting fixtures in a building addition may comply as a stand alone project, or they may be
79
combined with the overall existing bldg lighting to demonstrate compliance. Refer to C101.4.3.
6952
b. For retrofits and building additions, provide Building Area types and gross interior areas in the
Page E2.0
Maximum Allowed Lighting table. If a builidng addition will comply as combined with the overall
3
existing builidng, include all applicable existing Building Area types and gross interior areas.
174
c. Document new fixtures and all existing to remain fixtures in the Proposed Lighting table.
d. If less than 60% of existing fixtures will be replaced, use LTG -INT -SPACE form.
Maximum Allowed Lighting Wattage
Building Area*
Location (plan #,
room #, or ALL)
Area Description
Allowed
Watts per ft2
Gross Interior
Area in ft2
Wafts Allowed
(watts /ft2 x area)
School /university
Page E2.0
Classrooms, Restroom, Mech,
0.99
8283
8200
* Select Table C405.5.2(1) Building Area from drop down menu. Totall
8283
Proposed Lighting Wattage
Building Area*
Location (plan #,
room #)
Fixture Description **
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
School /university
Page E2.0
3 -Tube T8 32W Flouresent Lay -in with Elect.
Ballast
79
88
6952
School /university
Page E2.0
2 -Tube T8 32W Flouresent Lay -in with Elect.
Ballast
3
58
174
Select Table C405.5.2(1) Building Area from drop down menu.
** Include existing to remain lighting and exempt lighting equipment per notes below.
Compliance by Building Area
Building Area
Warnings
Total Allowed
Watts
Total Proposed
Watts
Interior Lighting Power
Allowance
School /university
8200
7126
COMPLIES
Total 8200 7126
Notes:
1. Proposed Wattage for each Building Area type shall not exceed the Allowed Wattage for that Building Area type. Trading wattage between
Building Area types is not allowed under the Building Area Method compliance path.
2. Proposed fixtures must be listed in the building area in which they occur. Include ALL proposed lighting fixtures.
3. For proposed Fixture Description, indicate fixture type, lamp type (e.g. T -8), number of lamps in the fixture, and ballast type (if included). For
track lighting, list the length of the track (in feet) in addition to the fixture, lamp, and ballast information.
4. For proposed Watts/Fixture, use manufacturer's listed maximum input wattage of the fixture (not simply the lamp wattage) and other criteria
as specified in Section C405.5.1. For line voltage track lighting, list the greater of actual luminaire wattage or length of track multiplied by 50,
or as applicable, the wattage of current limiting devices or of the transformer. For low voltage track lighting list the transformer rated wattage.
5. For lighting equipment eligible for exemption per C405.5.1, note exception number and leave Watts/Fixture blank.
6. Document existing to remain fixtures in Proposed Lighting table in the same manner as new fixtures. Identify as existing in fixture description.
• • • Summary
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Info Project Address: 2016 -09 KCDA Yelm High III Date 4/14/2016
1315 Yelm Ave. West For Building Department Use
Yelm, WA 98597
Applicant Name: Modern Building Systems, Inc.
Applicant Addr: 9493 Porter Rd, Aumsville, OR 97325
Applicant Phone: 503- 749 -4949
Project Description ❑ New Building ❑ Addition ❑ Alteration ❑ Plans Included
Lighting Zone
As specified by jurisdiction. Zone selection ❑ Zone 1 0 Zone 2 Zone 3 0 Zone 4
required to enable LTG -EXT form
Compliance Option * Lighting Power Density Calculations 0 Total Building Performance
Building Grounds
Applies to luminaires > 100 Watts
❑ Efficacy> 60 Iumens/W ❑ Controlled by motion sensor
❑ Exemption (list)
Exterior Lighting Alterations No changes are being made to the existing exterior lighting
❑ New wiring installed to serve added fixtures and /or fixtures relocated to new circuit
Provide applicable exterior lighting controls per C405.2.4 and commissioning per
Tradable Maximum Allowed Lighting Wattage Base Site Allowance: 750
Allowed a s Area (ft), perimeter Allowed Watts
Tradable Surfaces Surface Description per fe or per If (If) or # of items x ff (or x If)
Main Entry Door Door #1 30W /LF door 6 180
width
Other Entry Door Door #2 20W /LF door 6 120
width
Total Allowed Tradable Watts: 300
Tradable Proposed Lighting Wattage (Use mfgr listed maximum input wattage for luminaire.)
Tradable Surface
Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Main Entry Door
42W Compact Fluorescent Wall Pack
1
42
42
Other Entry Door
42W Compact Fluorescent Wall Pack
1
42
42
Total proposed tradable watts may not exceed the sum of total allowed tradable Total Proposed Tradable Watts:
. — -11 sti_ ti--- -;r - -, u,...,.,..,.,, A., , I. - ;fo nnf no Hl q fn mn4a
84
tradable watts comply can be applied to individual non- tradable categories.
Non - Tradable Maximum Allowed Lighting Wattage Base Site Allowance Remaining:
750
Non - Tradable Surfaces
Surface Description
Allowed Watts
per ftz or per If
Area (ft), perimeter
(If) or # of items
Allowed Watts
x fe (or x If)
Non - Tradable Proposed Lighting Wattage
Non - Tradable Surface
Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Non - tradable proposed watts may not exceed allowed watts for any individual Total excess Non - Tradable watts: 0
surface unless the total excess watts for all non - tradable surfaces are less than the
Site Allowance Balance: 750
remaining site allowance.
Exterior Lighting COMPLIES WITH SITE ALLOWANC
MIA
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 2016 -09 KCDA Yelm High III
Date 4/14/2016
The following information is necessary to check a permit application for compliance with the lighting, motor, and transformer requirements in the
Washington State Energy Code, Commercial Provisions.
Applicability
Location in
Building Department
(yes, no,na)
Code Section
Component
Compliance information required in permit documents
Documents
Notes
LIGHTING CONTROLS (Section C405.2)
Indicate on plans the manual control type & locations served;
E0.1, & E2.0
Yes
C405.2.1.1
Manual interior
Indicate of plans the 50% lighting load reduction method
Exception 2
C405.2.1.2
lighting controls
provided or identify exception taken
Indicate lighting system automatic shut -off capability - identify
E2.0
lighting zone areas served on plans;
Automatic time
--
Indicate locations of override switches on plans and the areas
NIA
Yes
C405.2.2.1
switch controls and
served, include area sq. ft.;
override switching
Indicate locations where automatic shutoff is provided by other
methods (occupancy sensor, daylight controls, etc)
E2.0
Yes
C405.2.2.2
Occupancy sensors
Indicate on plans the locations served by occupancy sensors
E2.0
Daylight zones -
Indicate vertical fenestration primary and secondary daylight
E2.0
Yes
C405.2.2.3
Vertical fenestration
zone areas on plans, include sq. ft.;
Indicate skylight daylight zone areas on plans, include sq. ft.
and skylights
N/A
Indicate on plans the locations served by daylight zone controls;
E0.1 & E2.0
Yes
C405.2.2.3.2
Daylight zone
controls
Indicate in plans the lighting load reduction (dimming) method -
stepped or continuous dimming
E0.1
Specific application
Indicate on plans the locations served by specific application
NA
C405.2.3
lighting controls -
lighting controls
General
Indicate lighting control method for display and accent lighting,
and display case lighting;
NA
C405.2.3 -
Display and accent
- -
Indicate these fixtures are controlled independently from both
—
Items 1 &2
lighting
general area lighting and other lighting applications within the
same space
Provide a lighting control device at each guest room entry for all
NA
C405.2.3 -
Hotel /motel guest
permanently installed fixtures in guest room;
—
-
Item 3
rooms
-- -
-- -
Indicated whether lighting control is manual or automatic
C405.2.3 -
Supplemental task
Provide automatic shut -off vacancy controls for supplemental
NA
Item 4
lighting
task lighting, including under -shelf or under - cabinet lighting
Identify eligible non - visual applications and method of lighting
control;
NA
C4052.3 -
Lighting for non -
Indicate these fixtures are controlled independentl y from both
Item 5
visual applications
general area lighting and other lighting applications within the
same space
Indicate lighting control method for lighting equipment for sale
Lighting equipment
or demonstration;
NA
C405.2.3 -
for sale or
Indicate these fixtures are controlled independently from both
Item 6
demonstration
general area lighting and other lighting applications within the
-
same space
If egress lighting power density is greater than 0.05W /ftz,
indicate method of automatic shut -off during unoccupied
NA
C405.2.3 -
Means of egress
periods;
Item 7
lighting
--
Identify on plans the egress fixtures that function as both normal
and emergency means of egress illumination
Provide vacancy device or timer to turn off fixtures within 15
NA
C405.10
Cooler and freezer
minutes of unoccupancy for cooler and freezer lighting fixtures
C405.11
lighting
with lamp efficacy less than 40 1 umens per watt
Exterior lighting
Indicate on exterior lighting plans the automatic lighting control
E2.0
Yes
C405.2.4
controls
method and locations served
Exterior building
Provide motion sensor controls for building grounds fixtures
NA
C405.6.1
grounds lighting
rated at greater than 100 watts with lamp efficacy less than 60
controls
lumens, or identify exception taken
Identify applicable commissioning documentation requirements
A0.0
per Section C408 or el igibility for exception;
Provide written procedures for functional testing of all automatic
Lighting system
A0.0
Yes
C408.3
functional testing
controls and describe the expected system response,
Identify in construction documents the party responsible for
AO .0
functional testing of automatic lighting controls
INTERIOR
LIGHTING POWER & EFFICACY Sections C405.5, C405.10, C405.11
2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 & R3 over 3 stories and all R1 Revised Jan 2014
Project Address 2016 -09 KCDA Yelm High III
Date 4/14/2016
The following information is necessary to check a permit application for compliance with the lighting, motor, and transformer requirements in the
Washington State Energy Code, Commercial Provisions.
Applicability
Location in
Building Department
(yes,no,na)
Code Section
Component
Compliance information required in permit documents
Documents
Notes
Provide fixture schedule with fixture types, lamps, ballasts, and
LTG -INT -SPACE
rated watts per fixture;
Identify spaces eligible for lighting power exemption on plans
C405.5.1
C405.5.1.1
Total connected
and in compliance forms;
P
N/A
- _-
Yes
C405.5.1.2
interior lighting power
Identify lighting equipment eligible for exemption in fixture
NIA
C405.5.1.3
schedule and in compliance forms;
C405.5.1.4
N/A
Indicate that exempt lighting equipment is in addition to general
area lighting and is controlled independently
Provide exit sign types and rated watts per fixture in fixture
N/A
NA
C405.4
Exit signs
schedule (maximum 5 watts per fixture)
For lighting in walk -in coolers and freezers, and refrigerated
NA
C405.10
Cooler and freezer
warehouse coolers and freezers, provide rated lamp efficacy (in
-
C405.11
lighting
lumens per watt) in fixture schedule
Lighting Power Calculation - Indicate compliance path taken
Complete required compliance forms - proposed wattage per
NA
C405.5.2
Building Area Method
building area does not exceed maximum allowed wattage per
Attached
building area. Identify locations of building areas on plans
Complete required compliance forms - total proposed wattage
Space -By -Space
does not exceed maximum allowed wattage. Identify locations
Yes
C405.5.2
Method
of space types on plans, including retail display areas as
applicable
EXTERIOR LIGHTING POWER & EFFICACY Section C405.6
Provide fixture schedule with fixture types, lamps, ballasts, and
LTG -EXT
rated watts per fixture;
_.
Total connected
Identify exterior applications eligible for lighting power
NIA
Yes
C405.6.2
exterior lighting
exemption on plans and in compliance forms;
power
-
Indicate that exempt exterior lighting is controlled independently
N/A
from non -exem pt exterior lighting
Yes
Table
Exterior lighting zone
Indicate building exterior lighting zone as defined by the AHJ
LTG -EXT
C405.6.2(1)
For building grounds fixtures rated at greater than 100 w atts,
NA
C405.6.1
Exterior building
provide rated lamp efficacy (in lumens per watt) in fixture
grounds lighting
schedule
Complete required compliance form - proposed wattage for
Yes
C405.6.2
Exterior lighting
exterior lighting plus base site allowed does not exceed
Attached
power calculations
maximum allowed
MOTORS & TRANSFORMERS (Sections C405.8, C405.9)
For motors not part of an HVAC system, provide electric motor
NA
C405.8
Electric Motors
schedule on electrical plans with hp, rpm, and rated efficiency
Provide distribution transformer schedule on electrical plans
NA
C405.9
Transformers
with transformer size and efficiency
2012 Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3
2012 Washin ton State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised June 2013
Project Info
Project Address 2016 -09 RCDA Yelm High III
Date 4/19/2016
1315 Yelm Ave_ West,
For Building Dept. Use
Yelm, WA 98597
Applicant Name: Modern Building Systems, Inc.
Applicant Address: 9493 Porter Road, Aumsville, OR 97325
Applicant Phone: 503- 749 -4949
Project Description
Briefly describe mechanical
system type and features.
D Includes Plans
(9) 3.5 Ton Wall -hung (GAS) Heat Pumps and economizers.
Drawings must contain notes requiring compliance with commissioning provisions per Section C408
Compliance Option
Simple System O Complex System O Systems Analysis
Equipment Schedules
Ftheplans. llowing information is required to be incorporated with the mechanical equipment schedules on
For projects without plans, fill in the required information below.
Coolin g Equipment Schedule
Equip.
ID
Equip
Type
Brand Name'
Model No.'
Capacity2
Btu /h
OSA CFM
or Econo?
SEER
or EER
IPLV3
Econmizer
Option or
Exceptions
Heat
Recovery
Y/N
A
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
B
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
c
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
D
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
E
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
F
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
G
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
H
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
J
SPVHP
Bard
W42G3 -B
42000
Yes
10.0 EER
-
Econo
N
Heatin g E ui ment Schedule
Equip.
ID
Equip
Type
Brand Name'
Model No.'
Capacity2
Btu /h
OSA cfm
or Econo?
Input Btuh
Output Btuh
Efficiency
Heat
Recovery
Y/N
A
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
B
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
C
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
D
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
E
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
F
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
G
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
H
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
J
SPVHP
Bard -Gas
W42G3 -B
50000
Yes
61000
50000
82% EFF
N
Fan Equipment Schedule
Equip.
ID
Equip
Type
Brand Name'
Model No.'
CFM
SID
HP /BHP
Flow Controls
Location of Service
EF -1
Exh.
Fan
Panasonic
FV -11VQ5
110
0.04
CV
Restrooms
EF -2
Exh.
Fan
Panasonic
FV- 40NLFI
440
0.17
CV
Restrooms
?n12 Washington State Enerav Code ComDliance Forms for Commercial, Group R1, and > 3 story R2 and R3
1 If available. 2 As tested according to Table C403.2.3(1)A thru C403.2.3(8). 3 If required. 4 COP, HSPF, Combustion Efficiency, or AFUE, as
applicable. 5 Flow control types: variable air volume (VAV), constant volume (CV), or variable speed (VS). 6 Economizer exception number per
Service Water Heating Equipment Schedule
Equip.
ID
Equip
Type
Brand Name'
Model No.'
Input
Capacity
Sub -
Category
EF'
Location of Service
WH -50
WH
Elect.
AO -Smith
ECT -52
<12kW
Resist.
0.91
Restrooms
1 If available. 2 As tested according to Table C403.2.3(1)A thru C403.2.3(8). 3 If required. 4 COP, HSPF, Combustion Efficiency, or AFUE, as
applicable. 5 Flow control types: variable air volume (VAV), constant volume (CV), or variable speed (VS). 6 Economizer exception number per
2012'Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised .rune 2013
Project Address 2016 -09 KCDA Yelm High I I I Date 4/19/2016
The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012
WSEC. NOTE: Define print area in Excel orior to cirinting MECH -CHK pages.
Applicability
Code Section Code Provision Information Required
Location
Building Department
(yes,no,na)
on Plans
Notes
GENERAL PROVISIONS
Equipment Sizing & Performance
Yes
C403.2.1
Load calculations
Load calculations performed per ASHRAE Std 183 or equivalent per
Attached
Chapter 3
Equipment and system
Output capacity of heating and cooling equipment and systems do not
Yes
C403.2.2
sizing
exceed calculated loads note exceptions taken
Ventilation (natural or mechanical) provided per IMC; indicate mechanical
Yes
C403.2.5
Minimum ventilation
ventilation is capable of being reduced to minimum requirement per IMC
A0.0 & M 1.0
C403.2.3 &
Provide equipment schedules or complete MECH -SUM tables with type,
C403.2.3.2 &
Equipment minimum
capacity, efficiency, test standard (or other efficiency source) for all
Yes
C403.2.12.1
efficiency
mechanical equipment
MECH -SUM
N/A
C403.2.13
Electric motor efficiency
Provide equipment schedule with hp, rpm, efficiency for all motors; note
-
except.
Fan system motor hp or bhp does not exceed limits per Table
N/A
C403.2.10
Fan power limitation
C403.2.10.1 1
-
C403.2.10.3
hp fan
Indicate fan motors 1/12 to 1 hp are ECM type or meet minimum efficiency
N/A
& C403.2.13
Fractional motors
re q.
N/A
C403.2.3
Maximum air cooled chiller
Indicate air - cooled chiller capacity does not exceed air - cooled chiller limit
-
ca capacity
Non - standard water - cooled
Full -load and NPLV values forwater - cooled centrifugal chiller adjusted for
N/A
C403.2.1
chillers
non- standard operational conditions
-
Centrifugal fan cooling
Large capacity cooling towers with centrifugal fan(s) meet efficiency
N/A
C403.2.12.1.
towers
requirements for axial fan open circuit cooling towers
-
C403.2.3
Forced air fumace and unit
Indicate intermittent ignition or IID, flue /draft damper &jacket loss
-
N/A
heaters
Yes
C403.2.3.3
Packaged electric
List equipment required to be heat pumps on schedule
M1.0
heating/cooling equipment
Indicate method of humidification (note requirements for systems with
N/A
C403.2.3.4
Humidification
economizer)-
HVAC System Controls & Criteria
Yes
C403.2.4.1
Thermostatic controls
Indicate locations of thermostatic control zones on plans, including
M1
enmeter systems
.0
Yes
C403.2.4.1.1
Heat pump supplementary
Indicate staged heating (compression /supplemental) & outdoor lock -out
T -stat Specs
heat
tern
Yes
C403.2.4.2
Setpoint overlap
Indicate 5 °F deadband minimum for systems controlling both heating &
T -stat Specs
deadband
cooling
Automatic setback and
Indicate zone t -stat controls with required automatic setback & manual
Yes
C403.2A.3
shutdown
override
T -stat Specs
Yes
C403.2.4.3.3
Automatic (optimum) start
Indicate system controls that adjust equip start time to match load
T -stat S eCS
conditions
p
C402.4.5.2 &
Dampers
Indicate location of OSA, exhaust, relief and return air dampers; include
A0.0 & M1.0
Yes
C403.2.4.4
AMCA rated leakage and control type motorized or ravit note
N/A
C403.2A 1
Heating outside a building
Indicate radiant heat system and occupancy controls
-
N/A
C403.2A.5
Snow melt systems
Indicate shut -off controls based on outdoor conditions
-
N/A
C403.2A.6
Combustion heating
Indicate modulating or staged control
-
equipment
N/A
C403.2.4.7
Group R1 hotel /motel
Indicate method for guest room automatic setback & set -up of 5 °F
systems
minimum
N/A
C403.2.4.8 / S
Group R2 /R3 dwelling unit
Indicate 5 -2 programmable thermostats in primary spaces with minimum of
-
systems
two setback eriods note exceptions taken
N/A
C403.2.5.1
Demand controlled
Indicate high- occupancy spaces and systems requiring DCV
-
ventilation
Yes
C403.2.5.2
Occupancy sensors
p y
Indicate spaces requiring occupancy -based system control and method; or
T -stat Specs
alternate means provided to automatically reduce OSA when artiall
Enclosed loading
Indicate enclosed loading dock and enclosed parking garage ventilation
N/A
C403.2.5.3
dock/parking garage
system activation and control method
-
ventilation
N/A
C403.2.5.4.1
Kitchen exhaust hoods
Indicate kitchen hoods requir ng make -up air; indicate make -up air source
-
and conditionin method
Indicate lab exhaust systems requiring heat recovery, method & efficiency;
C403.2.5.4.2
Laboratory exhaust systems
or altemative method taken (VAV, semi-conditioned makeup, or CERM
N/A
calculation)-
Energy recovery -
Indicate ventilation systems requiring ER, method & efficiency; note
N/A
C403.2.6A
ventilation systems
exceptions
_
N/A
C403.2.6.2
Energy recovery -
Indicate on -site steam heating systems requiring energy recovery
-
condensate s stems
N/A
C403.2.6.3
Energy recovery -
Indicate remote refrig. condensers requiring ER and use of captured
-
condensers stems
ener
Mechanical P- rmit Plans Checklist - Page 2 of
2012'Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised June 2013
Project Address 2016 -09 KCDAYelm High III Date 4/19/2016
The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012
WSEC. NOTE: Define print area in Excel prior to printing MECH -CHK pages.
Applicabildy
Code Section Code Provision
Information Required
Location
on Plans
Building Department
Notes
(yes,no,na)
GENERAL PROVISIONS, CONTINUED
HVAC System Controls & Criteria, Continued
Variable flow control -
Indicate fan & pump motors requiring VF control & method (VSD or equiv
N/A
C403.2.12
fans/pumps
controls
C403.2.12.1
Variable flow control -
Indicate cooling tower fans requiring variable flow control and method
_
N/A
cooling towers
Indicate fan systems requiring airflow reduction based on heating and
N/A
C403.2.12.2
Large volume fan systems
cooling demand; or exception taken
-
Indicate method of cooling demand -based fan control for sys. > 110,000
C403.2.12.2
Single zone AC systems
btuh
N/A
_
Identify all DDC system input/output control points and indicate capability
N/A
C403.2.4.10
DDC system capabilities
Ducting Systems
C403.2.7.1 &
Indicate all ductwork constructed and sealed per IMC, C402 leakage
N/A
C403.2.7.3
Dud construction
requirements and IBC vapor retarder requirements
403.2.7.3.1-
Dud pressure
Identify location of low, medium and high pressure ductwork on plans
M1.0
Yes
classifications
High pressure duct leakage
Indicate high pressure dud leakage testing requirements on plans, provide
N/A
C403.2.7.3.3
test
test results to jurisdiction when completed
-
Yes
C403.2.7.1 !
Dud insulation
Indicate R -value of insulation on ductwork
M1.0
Piping Systems
N/A
C403.2.8
Piping insulation
Indicate R -value of insulation on piping
_
N/A
C403.2.8.1
Piping insulation exposed to
Indicate method of protection from damage /degredation
_
weather
SIMPLE SYSTEMS
Qualifying Systems
C403.3
Qualifying single zone
Verify unitary or packaged equipment does not exceed capacity limits, does
Mech Unit Specs
Yes
systems
not have active humidification or simultaneous heating/cooling
C403.3
Qualifying 2 -pipe heating
Verify 2 -pipe heating -only system does not exceed capacity limits
_
N/A
systems
N/A
C403.3.2
Hydronic system controls
Refer to Complex Systems Section C403.4.3
_
Simple System Economizers
C403.3.1
Air economizer required
Indicate cooling systems requiring economizer controls; note in equip
M1.0
Yes
shed.
Yes
C403.3.1.1.1
Air economizer capacity
Indicate modulating OSA control capability up to 100% OSA, or exception
A0.0
C403.3.1.1.3
Air economizer high limit
Indicate high limit shut -off control method per Table C403.3.1.1.3(2)
A0.0
Yes
controls
Integrated air economizer
Indicate capability for partial air economizer operation for systems with
N/A
C403.1.1.2
o eration
ca acit > 65,000 btuh
-
Indicate eligible exception(s) taken and provisions to comply with
N/A
C403.3.1
Air economizer exceptions
-
COMPLEX SYSTEMS
Complex System Economizers
Indicate cooling systems requiring economizer controls, note in equip
N!A
C403.4.1
Air economizer required
sched.
-
Economizer heating system
Verify control method of HVAC systems with economizers does not
N/A
C403.4.1.4
impact
increase building heating energy usage during normal operation
_
Integrated economizer
Indicate capability for partial economizer operation for air or water econo
N/A
C403.4.1.3
o eration
systems
-
Indicate water econo capable of 100% cooling capacity at 50 °F db /45 °F wb
N/A
Moved
Water economizer capacity
OSA
-
Water economizer
Indicate precooling coils and heat exchangers do not exceed pressure drop
N/A
C403.4.1.2
maximum pressure drop
limit
-
Indicate eligible exception(s) taken and provisions to comply with
N/A
C403.3.1
Air economizer exceptions
Mechanical Permit Plans Checklist - Page
2012 Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised June 201
Project Address 2016 -09 KCDAYelm High III Date 4/19/2016
The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012
WSEC. NOTE: Define print area in Excel prior to printing MECH -CHK pages.
Al plicabilty
Code Section Code Provision Information Required
Location
on Plans
Building Department
Notes
(yes,no,na)
COMPLEX SYSTEMS, CONTINUED
Specific System Requirements
N/A
C403.4.2 &
Variable flow control - fans
Indicate fans requiring variable flow control and method
C403.2.12
VAV fan static pressure
Indicate sensor locations on plans, include at least one sensor per major
N/A
C403.4.21
sensors
dud branch
-
VAV fan static pressure
Indicate fan system static pressure setpoint based on zone requiring most
N/A
C403.4.2.2
setpoint
pressure
Indicate supply air systems serving multiple zones that are required to be
C403.4.5
VAV systems serving multi-
VAV, method of primary air control, and zones served, note exceptions
N/A
zones
taken
-
to controls that automatically reset supply air temp in response to
N/A
C403.4.5.4
VAV system supply air reset
loads
-
Large capacity cooling
Indicate method of multi -stage or variable control for building cooling
N/A
C403.4
systems
system capaoity capacity > 300 tons
-
N/A
C403.4.7
Hot gas bypass limitation
Indicate cooling equipment unloading or capacity modulation method
_
N/A
C403.4.3
Large capacity boiler
s stems
Indicate multi -stage or modulating burner for single boilers > 500,000 btuh
_
N/A
C4014.3
Boiler sequencing
Indicate automatic controls that sequence operation of multiple boilers
_
Chiller / boiler plant pump
Indicate capability to automatically reduce overall plant flow and shutoff
N/A
C403.4.3.5
isolation
flow through chillers & boilers when not in use
-
N/A
C403.4.2 &
C403.4.3.6
Variable flow control -
pumps
Indicate pumps requiring variable flow control & method
-
C403.2.12.1
Variable flow control -
Indicate cooling tower fans requiring variable flow control and method
N/A
& C403.4.4
cooling towers
Hydronic system part load
Indicate heating & chilled water systems have the capability to automatically
N/A
C403.4.3.4
controls
reset supply water temp AND reduce flow by ? 50% fors stems > 300,000
-
Two -pipe changeover
Indicate deadband, heating /cooling mode scheduling and changeover
N/A
C403.4.3.2
systems
temperature range
Water loop heat pump -
Indicate capability of central equipment to provide min. 20 °F water supply
N/A
C403.4.3.3.1
deadband
temp deadband between heat rejection and heat addition modes
-
Water loop heat pump -
Provide heat exchanger that separates cooling tower and heat pump loop
N/A
C403.4.3.3
heat re edion
in Climate Zone 5
Water loop heat pump -
Indicate 2 -way isolation valve on each heat pump and variable flow control
N/A
C403.4.3.3.3
isolation
fors stems with total pump power > 10 hp
-
I
N/A
C403.4.6
Condenser water heat
Indicate system provided to pre -heat service water and efficiency
_
recovery
Cooler / freezer - anti -sweat
Indicate w /sf & control method for walk -in cooler /freezer door anti -sweat
N/A
C403.5
heaters
heaters
N/A
C403.5 / 6
Cooler / freezer - evaporator
Indicate motor type for evaporator and condenser fans < 1 hp
-
SERVICE WATER HEATING
Service Water Systems
C404.2
Water- heating equip min.
Provide equipment schedule or complete MECH -SUM table with type,
MECH -SUM
Yes
efficient
ca a ity, efficiency, test standard or other efficient source
Yes
C404.3
Temperature controls
Indicate temperature controls have required setpoint capability
P1.0
Indicate piping connected to equipment have heat traps on supply &
P1.0
Yes
C404.4
Heat traps
discharge
C404.5
Insulation underwater
Indicate R -10 insulation under tank
_
N/A
heater
C404.6
Service water piping
Indicate R -value of insulation on piping, note exceptions taken
P1.0
Yes
insulation
Circulation systems and
Indicate shutoff capability based on occupancy and periods of limited
N/A
C404.7 / g
heat trace shut -off
demand
-
Group R -2 service hot water
Indicate method of usage metering for dwell. units served by central HW
N/A
C404.9
Imeters
-
Pools & In- Ground Permanently Installed Spas
Provide equipment schedule or complete MECH -SUM table with type,
C404.10.1
Pool heating equip min.
capacity, efficiency, test standard (or other eff. source), heat pump heaters
N/A
efficiency
> 4 COP
Indicate automatic on /off control based on scheduling & accessible on /off
N/A
C404.10.1 / 2
Pool heater on / off controls
switch on heater that operates independent of thermostat setting; or
-
N/A
C40410.3
Pool covers
Indicate vapor retardant cover and insulation rating as required
_
N/A
C40410.3
Pool assembly insulation
Indicate rating of insulation on sides and bottom of pools heated to > 90 °F
_
Indicate method, exhaust air temperature reduction and recovered energy
N/A
C404.10.4
Heat recovery
]use
-
I
Air Handler #1- Two Lennox 5 Ton Split Sytem Heat Pumps Total Load
Summary
Air Handler Description: Two Lennox 5 Ton Split Sytem Heat Pumps Constant Volume - Proportion
Supply Air Fan: Blow -Thru with program estimated horsepower of 1.1 u hr
Fan Input: 0% motor and fan efficiency with 0 in. water across the fan
Sensible Heat Ratio: 0.78 -- This system occurs 1 time(s) in the building. —
Air System Peak Time: 4pm in July.
Outdoor Conditions: Clg: 88° DB, 67° WB, 66.47 grains, Htg: 21° DB
Indoor Conditions: Clg: 75° DB, 50% RH, Htg: 72° DB
Summer: Ventilation controls outside air, - - -- Winter: Exhaust controls outside air.
Zone Space sensible loss:
107,061
Btuh
Infiltration sensible loss:
0
Btuh
Outside Air sensible loss:
334,418
Btuh
Supply Duct sensible loss:
0
Btuh
Return Duct sensible loss:
0
Btuh
Return Plenum sensible loss:
0
Btuh
Total System sensible loss:
Total Heating Required With Outside Air:
441 479
Heating Supply Air: 107,061 / (.986 X 1.08 X 16) _
Winter Vent Outside Air (100.0% of supply) _
Zone space sensible gain: 271,577 Btuh
Infiltration sensible gain: 0 Btuh
Draw -thru fan sensible gain: 0 Btuh
Supply duct sensible gain: 0 Btuh
Reserve sensible gain: 0 Btuh
Total sensible gain on supply side of coil:
Cooling Supply Air: 271,577 / (.986 X 1.1 X 20) _
Summer Vent Outside Air (22.2% of supply) _
Return duct sensible gain: 0 Btuh
Return plenum sensible gain: 0 Btuh
Outside air sensible gain: 39,239 Btuh
Blow -thru fan sensible gain: 2,957 Btuh
Total sensible gain on return side of coil:
Total sensible gain on air handling system:
0 CFM
6,160 CFM
6,160 CFM
6,160 CFM
12,524 CFM
2,784 CFM
2,784 CFM
441,479 Btuh
271,577 Btuh
42,197 Btuh
313,774 Btuh
Zone space latent gain: 76,204 Btuh
Infiltration latent gain: 0 Btuh
Outside air latent gain: 2,284 Btuh
Total latent gain on air handling system: 78 487
Total system sensible and latent gain: 92,261 Btu
Total Air Handler Supply Air (based on a 20° TD): 12,524 CFM
Total Air Handler Vent. Air (22.23% of Supply): 2,784 CFM
Total Conditioned Air Space:
8,283
Sq.ft
Supply Air Per Unit Area:
1.5121
CFM / Sq.ft
Area Per Cooling Capacity:
253.4
Sq.ft/Ton
Cooling Capacity Per Area:
0.0039
Tons /Sq.ft
�
Heating Capacity Per Area:
53.30 Bt h /Sq.ft
O OR
Total Heating Required With Outside Air:
441 479
Btu
usF'C9� 3 S -M
Total Cooling Required With Outside Air:
32.69
ons
. 14
(/& : 3 I. r Twlr s
\\ DISKSTATION \Desgin\Don\CHVAC_Area- 1\2016 -09 Yelm High School.CHV Tuesday, April 19, 2016, 10:09 AM
THE WALL- MOUNTTm GAS /ELECTRIC
Climate Control Solutions
Models: W24G3 to W60G3 Up to 10.5 EER GREENREFRIGEF
26,000 to 57,500 BTUH Cooling Capacity
34,000 to 102,500 BTUH Heating Capacity 1
The Bard Wall -Mount Electric Air Conditioner with gas fired heating is a self- contained
energy efficient system which is designed to offer maximum indoor comfort at a minimal
cost without using valuable indoor floor space or outside ground space.
This unit is the ideal product for versatile applications such as: new construction, modular
offices, school modernization, portable structures, correctional facilities, retail stores or
other commercial applications. Factory or field installed accessories are available to meet
specific job requirements.
Features
Eno*"
Air Conditioner Compressor: Pre - Painted 20 Gauge Zinc Coated
Scroll compressors are used on all models Steel Cabinet:
and no crankcase heaters are required. Cleaned, rinsed, sealed and dried before
the polyurethane primer is applied. The
R-410A Refrigerant: cabinet is handsomely finished with a
Designed with R-410A (HFC) non -ozone baked on textured enamel, which allows
depleting refrigerant in compliance with it to withstand 1000 hours of salt spray
the Montreal protocol and 2010 EPA tests per ASTM B117 -03.
requirements.
Liquid Line Filter Drier:
Protects system against moisture.
Aluminum Finned Copper Coils:
Grooved tubing and enhanced louvered
fin for maximum heat transfer and energy
efficiency.
High & Low Pressure Switches are Auto-
Reset:
Built -in lockout circuit resets from the
room thermostat. Provides commercial
quality protection to the compressor.
Compressor Control Module:
Standard on all units. Built -in off -delay
timer adjustable from 30 seconds to 5
minutes. 2- minute on -delay if power
interrupt. 120 - second bypass for low
pressure control, and both soft and manual
lockouts for high and low pressure controls.
Alarm output for alarm relay.
Phase Rotation Monitor:
Standard on all 3 phase scroll compressors.
Protects against reverse rotation if power
supply is not properly connected.
Twin Blowers:
Move air quietly. All models feature
multispeed blower motors providing
airflow adjustment for high and low static
operation.
Electrical Components:
Are easily accessible for routine inspection
and maintenance through a right side
service panel opening. Features a lockable,
hinged access cover to the circuit breaker.
16 Gauge Zinc Coated Unit Base.
Heat Exchanger.
Heavy duty 18 -gauge stainless steel
tubular heat exchanger. Mechanically
joined construction. Ten -year warranty.
In -Shot Burners:
Advanced burner design, quiet
operation.
Built -in Circuit Breakers:
Standard on all single (230/208
volt) and three phase (230/208 volt)
equipment. Toggle disconnects are
standard on all three phase (460 volt)
equipment.
Integrated DSI Control:
Direct spark ignition control and remote
sensor delivers smooth, proven ignition
sequence. Timed blower control
and diagnostics are also features of
integrated control.
Gas Controls:
Honeywell gas valve and burner orifices
are factory standard for natural gas.
High altitude kits available. Field
convertible to LP gas with certified
conversion kit.
Filter Service Door:
Separate service door provides easy
access for filter change.
Condenser Fan and Motor Shroud
Assembly:
Slides out for easy access.
Air Filters:
Two-inch pleated air filters are standard equipment.
Optional 1 -inch washable filter available.
Factory or field installed.
Barometric Fresh Air Damper:
Standard on all units. Allows up to 25% outside
fresh air.
Ventilation Options:
Several ventilation options are available and can be
factory or field installed.
Slope Top:
Standard feature for water run -off.
Top Rain Flashing:
Standard feature on all models.
Full Length Mounting Brackets:
Built into cabinet for improved appearance and easy
installation. NOTE: Bottom mounting bracket
included to assist in installation.
Evaporator Freezestat:
Standard on dehumidification models.
• Complies with efficiency requirements of ANSI /ASHRAE/IESNA 90.1 -2010.
a Certified to ANSI /ARI Standard 390 -2003 for SPVU (Single Package Vertical Units).
Intertek ETL Listed to Standard for Safety Heating and Cooling Equipment ANSI /UL
1995 /CSA 22.2 No. 236 -05, Fourth Edition.
• Intertek ETL Listed to Standard for Gas -Fired Central Furnaces ANSI Z21.47 -2006,
CSA 2.3 -2006 Fifth Edition, Addenda A dated 10 -01 -2007, Addenda B dated 06 -01 -2008.
Commercial Product - Not intended for Residential application.
t�tl[RY,px.
C us
Intertek
Form No. 53500 -615
Supersedes NEW
Page 1 of 16
_r
Operating Voltage Range
197 -253
187 -253
414 -506
197 -253
187 -253
414 -506
197 -253
187 -253
414 -506
Minimum Circuit Ampacity
21
16
10
23
17
11
27
20
11
*Field Wire Size
10
12
14
10
12
14
8
14
Ground Wire Size
10
12
14
10
12
14
10
10
14
** Delay Fuse - Max.
30
25
15
35
25
15
40
25
15
ornpressor
Voltage
230/208
230/208
460
230/208
2301208
460
230/208
230/208
460
Rated Load Amps
9.9/10.9
6.4/7.1
3.9
11.8/12.9
7.5/8.2
4.7
12.4/14.0
7.8/8.8
4.9
Branch Circuit
12.8
8.3
5.1
141
9
5.6
16.7
10.5
5.8
Selection Current
Lock Rotor Amps
64/64
58/58
28
77!77
71171
38
79/79,
73/73
38
Compressor Type
Scroll
Scroll
Scroll
Scroll
Scroll
Scroll
Scroll
Scroll
Scroll
an Mofpr & Corxinnser
ti,
_ a >:;.
Fan Motor -HP- RPM -SPD
1/5- 1050 -1
�
1/5- 1050 -1
1/5 -105 0 1
1/5 1050 -1
1/5 1050 1
1/5-1050-1
1/5 -1050 1
1/5-1050-1
1/5-1050-1
Fan Motor -Amps
1.5
120'
1.5
8
1.5
120 1
1.5
8
120
1.5
1.5
.8
Fan D1A/CFM
20 2400
- 2400
20 2400
2400
20 2400
20 - 2400
2400
20 - 2400
201-2400
Blower Motor HP -RPM -SPD
1/4 -950 -3
1/4 -950 -3
1/4 -950 -3
1/3- 1075 -3
1/3-'1'075-3
1/3- 1075 3
1/3- 1075 -3
1/3- 1075 -3
1/3- 1075 -3
Blower Motor -Amps
1.8
1.8
.8
2.2
2.2
1.1
2.2
2.2
1.1
CFM Cooling & E.S.P.
800-15 .15
800 - .15
800-15 .15
1000 - .35
1000 - .35
1000 1000-35
1100-25 .25
1100 - .25
1100-25
Filter Size
20x25x2
20x25x2
20x25 x2
20x25x2
20x25x2
20x25x2
20x25x2
20x25x2
20x25x2
30k 3 PE�c
J
*Based on 75'C copper wire. All wiring must conform to the National Electrical Code and all local codes. 35A t p
C -L&
* *Maximum time delay fuse or HACR type circuit breaker.
Form No. S35OG -615
Supersedes NEW
Page 2 of 16
Input 90,000 81,000 68,000 61,000 45,000 41,000
Output 74,000 66,500 55,500 50,000 37,000 34,000
Thermal Efficiency (T.E.)
82.0
82.0
82.0
82.0
82.0
82.0
Temp. Rise Range
50-80
W24G3; W30G3 W35G3` -'
W42G3
W48G3'
) W60G3`
s Capacity BTUH ®
26,000
32,000
940
35,000
42,000
48,000
57,500
COW
10.0
10.0
730-1275
10.2
10.0
10.5
10.1
EER m
800
1000
Mid -Rise Range Airflow
1100
1300
1550
1650
Rated CFM
Airflow Range
680-920
850-1150
935-1265
1030 - 1500
1280 - 1750
1340-1910
Acceptable
90,000
90,000
1120
90,000
125,000
125,000
125,000
68,000
68,000
1290
68,000
100,000
100;000
100,000
Available Heating Inputs ®
45,000
45,000
790
45,000
75,000
75,000
75,000
1030
D Capacity is cert'rfied in accordance with ANSI/P RI Standard 390 -2003.
.40
1150
990
® EER = Energy Efficiency Ratio and is certified in accordance with ARI Standard 390 -2003.
1190
1030
1190
All ratings based on fresh air intake being 100% closed (no outside air introduction).
860
.50
910
710
0 Any one of the heating inputs shown is available for each basic cooling model as indicated.
Each input can be field derated
10% from factory standard and main
burner orifices are included with each unit to accomplish this. See table below for additional
information.
.50
Input 90,000 81,000 68,000 61,000 45,000 41,000
Output 74,000 66,500 55,500 50,000 37,000 34,000
Thermal Efficiency (T.E.)
82.0
82.0
82.0
82.0
82.0
82.0
Temp. Rise Range
50-80
50-80
40-70
40-70
25-55
25-55
Mid -Rise Range Airflow
1040
940
925
825
830
740
Acceptable Airflow Range
845-1350
765-1220
730-1275
650 - 1135
610-1330
540-1185
Heating ratings certified in accordance with ANSI 221.47 -2006_
40-70
30-60
30-60
Mid -Rise Range Airflow
1410
Heating ratings certified in accordance with ANSI 221.47 -2006.
t t t 1 t t! t E ! ! 4.1 `
W24G cooling airflow is rated 800 CFM 0 .15 ESP, and wet coil range is 700 - 910 CFM. W30G cooling airflow is rated 1000 CFM 0 .35 ESP, and wet coil range is 880 - 1150 CFM.
See Heating Airflow Ratings Chart for heating details. See Heating Airflow Ratings Chart for heating details.
.10
gar stoma
ale Fmys`tanaa<ae1a
tlerate fir saa ate
Input
125,000
113,000
100,000
90,000
75,000
68,000
Output
102,500
93,000
82,000
74,000
61,500
56,000
Thermal Efficiency (T.E.)
82.0
82.0
82.0
82.0
82.0
82.0
Temp. Rise Range
50-80
50-80
40-70
40-70
30-60
30-60
Mid -Rise Range Airflow
1410
1270
1365
1230
1250
1135
Acceptable Airflow Range
1145-1830
1 1030 - 1650
1075 - 1875
965-1700
940-1875
850-1700
Heating ratings certified in accordance with ANSI 221.47 -2006.
t t t 1 t t! t E ! ! 4.1 `
W24G cooling airflow is rated 800 CFM 0 .15 ESP, and wet coil range is 700 - 910 CFM. W30G cooling airflow is rated 1000 CFM 0 .35 ESP, and wet coil range is 880 - 1150 CFM.
See Heating Airflow Ratings Chart for heating details. See Heating Airflow Ratings Chart for heating details.
.10
820
1260
1060
1060
870
.10
10001
1260
1 10601
1260 1
1060
.20
950
770
1200
1010
1200
1010
.20
1160
950
1370
1200
1 1010
1200
1010
.30
880
700
1120
1120
940
.30
1080
880
1290
1120
940
1120
940
.40
790
1030
1030
860
.40
1150
990
1190
1030
1190
1030
860
.50
910
710
950
.50
1050
910
1090
950
1090
950
.60
800
840
.60
940
980
980
840
ESF
00 mg Mode
Iv1Aif{1ALFANand HEATING MODE
ESP
Cooling "Mode
11
MANUAi FAN and 'HEATI+jG
MODE:
inches
Wet Oo[I
6$,000 BTU input',
61;000 BTU
Input
Inches
Wet Cdjl
68,000 BTU Input::.
61,000 BTU, ]nput ,
HzQ
Higti,
Med
Med
Ldw
high`'
Med `
Low
Hz0
High :
Low
High ;
law;
tilgh
`Me`d .
;Low
.10
820
1260
1060
870
1060
870
.10
1000
1260
1060
1060
.20
950
770
1200
1010
1010
810
.20
1160
950
1200
1010
1010
.30
880
700
1120
910
1120
940
.30
1080
880
1120
940
1120
940
.40
790
1030
1030
860
.40
1150
990
1190
1030
860
1030
860
.50
910
710
950
950
780
.50
1050
910
1090
950
780
1090
950
780
.60
800
840
.60
940
980
840
980
840
660
ESP
MANUALfANand HEATING MODE
ESp
Oooling Mode
MANIJAt FAN and hEATI.tJ6 Mi3OE "
inches
45O(i0 BTUtnp ..
41, OD BTII input
ncs
Wetol
, p.
;BTU
InputHZO
Med
idw
High =
Med ::
low
HzO:
High
.10
it
1260
1060
870
1660
870
.10
1000
1260
1060
1060
.20
1200
1010
810
1200
1010
810
.20
1160
950
1200
1010
1200
1010
.30
1120
910
1120
940
750
.30
1080
880
1290
1120
940
1120
940
.40
1030
860
1030
860
680
.40
1150
990
1190
1030
860
1030
860
.50
910
710
950
780
950
780
.50
1050
910
1090
950
780
1090
950
780
.60
800
1
840
840
.60
940
980
840
1 660
1 980
840
1 660
Voltage adjustment
- Reduce
airflow by
100 CFM
for 208
Volt
Voltage adjustment
- Reduce airflow by 100 CFM
for 208
Volt
Dehumidification coil adjustment - Reduce
airflow by 35 CFM for dehumidification
coil installed
Dehumidification coil adjustment - Reduce
airflow by 35 CFM for dehumidification
coil installed
Top outlet
adjustment - Increase airflow by 50 CFM for top outlet
models
Top outlet adjustment - Increase airflow by 50 CFM for top outlet models
SG -3, RG -3, non - ducted application adjustment - Reduce airflow
by 100 CFM for SG -3
SG -3, RG -3, non -ducted application adjustment - Reduce airflow by 100 CFM for SG -3
and RG -3
installations
and RG -3
installations
Form No.
S3500-615
-
Supersedes
NEW
Page
3 of 16
4
25
4. 'P
f--
C-1
L
Cif w
CM
rC
04
z
ir.,
L a�
1.4
ti
M
z
tta
>
ix
0
L
C)
ED,
4:71
>
U5
0
;r-
tv
i
1,4
'3
CA !Te-9 11-1
rn
Va
>
ilz
G!
>
iw#O
Ge
04
z
ir.,
L a�
1.4
ti
O
J
LOY
z
0.0
TZ
LA
Yt
CO
m M
X. M.
m
W
M
z
tta
ix
0
L
C)
ED,
4:71
CO
'3
Va
ilz
G!
O
J
LOY
z
0.0
TZ
LA
Yt
CO
m M
X. M.
m
W
ztt�io�s
A
Item 1 Of 4 1 Next
Product Into Literature
VisionPRO® 8000 with Red LINKTM technology for residential or commercial use
PmtPace 1 1 SHARE 3 a•
TH8321R1001JU
VisionpRM 8000 with Red LI 1K"-' technology for residential or commercial use. Stages up
to Up to 3 beat 12 Cool.
Accessories & Replacement Parts
Overview
VisionP 09.8000 with RedLINKT"' is a 7 dayprogramnmable touenscreen thermostat that is selectable for residential or dgttt c om nerciat
use. The thermostat can be wired directly to the equipment, used with the THM5421 R 1021 Equipment Interlace Module or used with the
THM4000R1000 TrueZONE Wreless Adapter, Works with the RedLINKT° accessories including the RedLINKTf1 Internet Gateway,
Portable Comfort Control, Wreless Outdoor Sensor. Wireless indoor Sensor, Wreless Enhy/ExitRemote and Wreless Vent and Filter
Boost Remote.
Features
• Thermostat works standalone or Wth the THM5421R1021 Equipment Interface Module or with the TrueZONE Wreless
Adapter,
• Smart Schedule - programs in seconds for any lifestyle.
• Patented interview based programming and installer setup.
• RedLINK"-1 wireless communication.
• Increase profit per job by including RedLINKT}" accessories that provide comfort and convenience. RedLINKT' accessories
include the RedLINKT"' Internet Gateway, Portable Comfort Control (PCC), Wireless Outdoor Sensor, Wireless IndoorSensw,
Wireless Entry/Exit Remote, Wireless Vent and Filter Boost Remote, TrueSTEAM 110 humidifier with Wireless Adapter and
TrueZONE@ zoning panel with Wireless Adapter.
• Selectable for residential and light commercial applications. Meets commercial code and is title 24 compliant.
• Light commercial - commercial language (occupied and unoccupied), schedule holidays and custom events, remote setback,
economizer and time of day. Remote Setback requires the THM5421RIO21 Equipment Interface Module.
• Plain language setup, no manual needed.
• Alerts and User Interactions Log - Keeps a searchable history of alerts and setting changes to the thermostat to determine if
there is a system malfunction or if the issue was caused by a user error. Saves time in troubleshooting and points the
technician in the right direction. The Alert and User Interaction Logs are viewable on a computer after you download them
from the thermostat to a microSD card.
• Customizable Service Reminders allow dealers to remind their customers when its time to call for service, when their
warranty is expiring and to provide customized alerts.
• MicroSD port for copying the Installer Setup, Customizable Reminders, Custom Events and Holidays to multiple thermostats.
• MicroSD port for adding the dealer's contact information on the screen.
• 1 assignable output on the TH8321 model to control humidification, dehumidification, ventilation or a stage of heating /cooling.
• 3 assignable outputs on the Equipment interface Module to control humidification, dehumidification, ventilation or a stage of
heating /cooling. The TH8110 and TH8320 models require the use of a Wireless Indoor Sensor to control humidification and
dehumidification.
• 1 assignable input can be used with a wired outdoor; indoor or discharge sensor.
• 4 assignable inputs on the. Equipment Interface Module can be used with 1.Vred outdoor, indoor or discharge sensors,
occupancy sensor for resole setback and dry contact devices to trip pre- packaged or custom alerts such as a full drain pan
or water leak.
• Extend wireless range of the Equipment Intetace Module by connecting a THM4000R1000 Wireless Adapter to the ADCD
tenninals:
• Dual powered battery or hardwired (C Wre).
• Precise temperature control ( +l- 1` F) for reliable and consistent temperature.
• Multiple staging options to provide comfort or energy savings.
Product Specifications
Hazmat lnformafton
UN 3091 Lithium metal batteries packed iniwith equipment
Application
Up to 31-112C heat pump or up to 2Iir2C conventional
Dimensions (in.)
4 518 in. High; 4 15,116 in. Wde,1 118 in. Deep
Dimensions (min)
118 mm. High, 126 mm. Wde, 29 rnm. Deep
Includes
VisionPRO@ 8000 thermostat
Used With
Works standalone orwith optional TI IM5421 R1021 Equipment
Interface Module and RedLINKT' accessories.
Item Type
Product
tlttps :llcustorner.honeywell.com /en -US /pages /Pi-oduct.aspx? cat= HonECC %2OCatalog &pid= TH8321R 1001 /U W
Y
1 a-,*
7102015-
Electrical Relinas
Frequency
Stages
Electrical Connections
Operating Humidity Range ( RH)
Supply Voltage
Switch Positions (Systern)
Switch Positions (Fan)
Operating Temperature Range (F)
Operating Temperature Range (C)
Color
Programmability
Power Method
Terminal Designations
Display Size
Chenueover
Setting Temperature Range (F)
Setting Temperature Range (C)
Humidification Setting Range
Dehumidification Setting Range
terms & conditions I privacy statement I site map
VSIonPROO 8000 with Redl-INKTI' technology for residential or commercial use
18 to 30 Vac or 750 mV
50 Hz, 60 Hz
Up to 3 Flea! 12 Cool Heat Pump or Up to 2 Heat 12 Cool
Conventional when used standalone; Up to 4 Heat / 2 Cool Heat
Pump of Up to 3 Heat /2 Cool Conventional when used with the
Equipment Interface Module.
Screw- terminals
5 to 90% RH, non - condensing
18 to 30 Vac or 750 rr:V
HEAT- OFF - COOL- AUl'O -E:M.H EA T
AUTO- ON- CIRC,FOLLOW SCHEDULE
32 F to 120 F
0C to48.9C
Arctic tNhite
7 -Day Multiple Day Programming or Non - Programmable
Battery or Hardwired
R, RC, C: W-O /B. V,12- AUX/E, Y, Y2, G, A -LA, K, U 1 U1, S1 S1
10 sq in.
Auto or tvlanual
Heal: 40 F to 90 F Cool 50 F to 99F
Heat: 4.5 C to 32L C. Cool: 10 C to 37.0 C
Cooling: 40 to 30% Rf L Heating: 10 to 60:i. PH,
40 to 80% RH.
tits"! r lkwatn
choose region & language honeywell international inc. 2015
https:Jtcustomer.ttoneywell .coin/en- USlpages/Product.aspx? cat= HonECC %20Catalog&pid= TH8321R10011U 212